Manufacturers

Yale 2100 Series Dogging Assembly

yale Part # 60-2100-1001-999

The Cal-Royal 2000 and 9000 Dogging Assembly is used on the 2200 and 9800 Series Exit Devices which include the 2200, 2260, 9800 and 9860.  The assembly uses a 7/32 inch dog key.

The Cal-Royal 221 Bottom Strike is used on the 2000, 5000, 7000 and 9000 Panic Bars with Surface Vertical Rods. Strike measures 2-7/16 inches long with a 5/16 inch projection.  The hole spacing is 1-7/8 inches.

The Dorma Surface Vertical Rod Top Strike 426 is used on the 8400, 8400F, 9400 and 9400F devices. Shims and mounting screws included.

The Cal Royal 938 Surface Strike is used on the 6600, 7700 and 5000 Series Rim Devices.  The strike includes all the mounting screws.

Yale 7000 Exit Device Dogging Assembly

Dogging assembly uses a 5/32" dog key

Yale Part # 60-7000-406-999
Sometimes call the 60-7000-0406-048

Adams Rite End Cap

On this Adams Rite End Cap we sometimes find the number HX0471 cast into the Black Plastic construction.

Adams Rite Part # 25-0471

This package connects to the rods on the Dorma 9400 Surface Vertical Rod Devices. Plate measures 3/4 x 1/2 inch, finger sticks up 3/4 of an inch. Package includes 2 plates and 2 screws.

Dorma 9400 Rod Guide and Screw Package, featuring two rod guides in the Stainless Steel finish.

The Monarch 4326 Spring Clip is used with the 4841 Spring in the older Monarch Lever Trims

Replacement Dorma 9000 Series End Cap, sometimes know as the EC9

Shown in Dark Bronze

Von Duprin 22 / 2227 Push Bar End Cap

Cap fits on the ends of the Von Duprin 22 Series Push Bar.

Von Duprin Part # 968598

Plastic end cap for all Adams Rite Concealed Vertical Rod and Mortise devices.

Plastic cap measures 2-3/8" high by 1-1/16" wide by 1-1/4" projection. The metal tab measures 1-3/16" wide by 5" long.

Adam Rite Part # 41-0901-05-IP

Von Duprin 2227 Center Case

Replaces worn out Von Durpin 2227 Center Cases. The Von Duprin 2227 is the 22 Series Device that has the Surface Vertical Rods.

Von Duprin Part # 109358

Von Duprin 2227 Rod Guide

Works on all of the Von Duprin 2227's, and replaces the older style that featured the plastic cap and the springs.

Von Durpin part # 112063

Von Duprin 2227 Latch Cover.

Package includes mounting screws

Von Duprin part # 050566

Von Duprin 2227 Top latch

This latch is used on devices shipped before October 1998, see related products for the new style latch if your device is newer. This is usually the problem if your bottom rod is dragging on the floor. Includes screws.

Von Duprin Part # 050091

Von Duprin 2227 Bottom latch.

Replaces and updates all 2227 bottom latches to the new style if you device was shipped before October 1998. If your device was shipped after October 1998 then use the G050401.

Includes screws and bracket

Von Duprin Part # 050090

Von Duprin 2227 Center Case Cover

The Von Duprin 2227 Center Case Cover comes in an Aluminum color or Dark Brown color.

Von Duprin Part # 968888

Von Duprin 22 Dogging Cover Plate. Plate covers the dogging assy, or hinge side of the exit device. This plate sides off when the plastic end cap breaks or goes missing.

Von Duprin Part # 968595

Von Duprin Exit Device 22 Center Case 109012

Von Duprin 22 Center Case. Replaces worn and broken Von Duprin 22 Center Cases

Von Duprin Part # 109012

Von Duprin Exit Device 22 Rim Center Case Cover

Replace your old or missing Von Duprin 22 Cover. This cover comes in aluminum or dark brown finishes.

Von Duprin part # 968603 SP28 or SP313

Replacement Chassis Cover for the Dorma 9300 Rim Device

The Adams Rite Metal End Cap is for the hinge side of the door and replaces the plastic version (25-0471).  This cap can be used on the 3100, 3300, 3600, 3700, 3900, 8100, 8200, 8300, 8400, 8500, 8600, 8700, 8800 and 8900.  We find the number 23-0600 cast in to the end cap.

Adams Rite Part Number 41-0903-IP or 41-0903-119

Von Duprin 230L Tailpiece Auxiliary Kit

The Von Duprin 230L Tailpiece Auxiliary Kit includes the Tailpiece, Tailpiece Guide, and the Pine Tree Clip.

Von Duprin Part # 900894

Detex EAX-300 Door Prop Alarm

The Detex EAX-300 Series is designed for applications where doors may be used for egress or ingress, but may not be held or propped open. Door open times from 1 second to 4 minutes (15 second default) are field selectable. The smaller size makes installation quick and easy.

Moritse Cylinder is not included
Powered by a 9 Volt Battery

Detex EAX-300 Installation Instructions

Monarch Trim Spring 4841

2-1/2" long x 3/16" diameter

Monarch part # 4841

Von Dupin 22 Plastic Cap Only

This is the end cap that goes on the hinge side of the door. When the cap breaks off the Dogging Cover Plate just slides off. Works on all of the Von Duprin 22 exit devices. If you need the bracket also, please order part # G22R10. Black plastic contruction. As of October 1, 2014, Von Duprin no longer sells just the Plastic Cap Only. The complete End Cap and Bracket 900981 will be shipped in its place.

Von Durpin Part # 968601

Von Duprin 22 Replacement End Cap and Bracket.

The bracket is constructed of zinc plated steel and the end cap is black plastic. Bracket also acts as mounting bracket that holds the exit device on the door.

Von Duprin part # 900981

The Cal-Royal CRCODE204 is for use with the 2200, 7700 and 9800 Rim and Surface Vertical Rod Devices. The Lever Mechanism features a Break Away Lever, for use with 1-3/4 inch to 2 inch thick doors, non-handed, Single Code User, Key Override, easy on the door code change, weather resistant, and more than 8000 non-sequential possible code combinations.

Installation and Programming Instructions

The Heavy Duty Cal Royal CRCODE101 is for use on the 7700 and 9800 Rim and Surface Vertical Rods. This lock features Single Code with up to 8000 code combinations, weather resistant, non handed, and code can be changed without removing the lock. Comes in Brushed Chrome finish only.

Installation and Programming Instructions

The Monarch 19-V Series Latch Cover is made of impact resistant black plastic.   The Monarch 19-V is now known as the Falcon 19-V.  The manufacture part # is 650388.

Yale 7100 Latch Cover

This latch cover is used on the Yale 7110 Surface Vertical Rod Device.  We stock these in Brushed Stainless Steel, other finishes will take longer.

Yale Part # 60-7010-7040

Monarch 19-V Series Chassis Assembly Cover

This is the cover for the Monarch Falcon 19-V Rim Device. The cover measures 5-7/8" tall by 2-1/2" wide with a projection of 1-7/8".

Monarch/Falcon part # 650385
Old Part # 6134

Monarch 19 Series Dogging Pin Package

Used on the Monarch 17,18 and 19 Series Panic Devices.  Pin measures 9/16" overall length with a 5/16" diameter head and 3/16" diameter shaft.  Sold as a package of 10.

Monarch Part # 060110
Old Part # 4086

Monarch 19 Series End Cap Bracket

This steel bracket holds the hinge side of the panic bar on the door. The end cap then fits over it for a finished look. Bracket measures 1-5/8" tall by 1-1/4" wide with a 15/16" projection. Sometimes shipped with a mounting barrel nut and screw.

Monarch Falcon Part # 650320 or old part # 600108