Von Duprin Strike 264
This strike measures 2-7/8" tall by 1-1/4" wide with a roller projection of 9/16". Used on the Von Duprin 22, 88, 98 and 99 when a lower profile strike is need in place of the Von Duprin 299 Strike. The hole spacing is 2-1/8" on center, and it ships with mounting screws and a shim. Also known as a Von Duprin Surface Roller Strike.264$97.67
Von Duprin Strike 385A
The Von Duprin 385A Strike is used on the floor for the Von Duprin 2227, 8827, 9827 and 9927 Surface Vertical Rods. The strike face plate outside dimensions are 2-1/4" x 2-1/4" with an inside dimension of 1-1/8" by 1". This floor strike features a bolt that can be cemented into the floor. Zinc plated finish.385A$112.00
Von Duprin Strike 1609
This strike is used when we have a double door application without a center post. By using this strike we can have one door with a surface vertical rod and one door a rim device, which will save money because vertical rods are usually expensive. This strike can be used with the Von Duprin 22/2227, 88/8827, 98/9827 and 99/9927 combinations, but not with the Fire Rated Versions. The strike base measures 1-1/16" wide by 3-1/4" high, the lip projects out 7/8". The three slots are 1-1/4" on center. This strike ships with the mounting screws.
Von Duprin Rim Strike 299
The Von Duprin 299 Strike is used on the 22, 88, 98, and 99 Rim Devices and also as a Top Strike on the 2227, 8827, 9927, and 9827 Surface Vertical Rod Panic Devices. The 299 strike measures 1-1/4" wide by 2-7/8" high with a slotted hole spacing of 2-1/8". The roller projects out 13/16".
Ships with shim and mounting screws299$55.39
Von Duprin Strike 299F
The Von Duprin 299F Strike is used on the 22, 88, 98, and 99 Fire Rated Rim Devices (no hex or cylinder dogging). The 299F strike measures 1-1/4" wide by 2-7/8" high with a slotted hole spacing of 2-1/8". The roller projects out 13/16". The non fire rated version would be the Von Duprin Strike 299.
Ships with shim and mounting screws299F$68.88
Von Duprin Strike 304L
This Von Duprin Strike is used for the bottom latch of the 2227, 8827, 9827 and 9927. The strike measures 1-7/8" by 1-7/8" outside dimension of the square flange, with an inside dimension of 1-1/8" by 1-1/8". The part that is inserted into the floor is 1-3/8" x 1-3/8" and drops down 13/16". Also known as a Von Duprin Floor Mounted Mortise Strike.304L$49.59
Von Duprin 88 and 55 Wedge Tite Screw.
This screw applies pressure to the wedge which then expands the wedge ring to key the Von Duprin 88 and 55's crossbars tite.
Von Duprin Part # 09008188R100$2.09
Von Duprin Exit Device 88 Tube Attaching Ring
Von Duprin 55 and 88 Tube Attaching Ring.
Used as a sleeve the wedge tite screw and wedge use to apply pressure to the crossbar. Measures 15/16" long by 13/16" diameter.
Von Duprin Part #090021
Old Part # 96567688R110$9.46
Von Duprin Exit Device 88 and 55 Cross Bar
Von Duprin 55 and 88 Cross Bar.
42" Cross bar is sent, you cut to size in the field.
Von Duprin Part # 050004
Old Part # 96773888R120-As low as $201.77
Von Duprin Exit Device 88 Mounting Screws
This mounting screw package is used on the 88 Exit Device, there description is 88C/C or E/C Mtg Pkg (CS and MS). The package includes 12 screws, 6 of each type.
Von Duprin Part # 900503
Von Duprin Exit Device 88 Axle Package
Von Duprin 88 Axle Package
New style axle snaps together, and replaces the old style which were screwed together with allen wrenches. This style of axle has been around since about 1990. The piece on the right is only used for taking the axle apart.
Von Duprin Part # 090006 or 09008288R40
Von Duprin Exit Device 88 Lever Arm Left Hand
Von Duprin 88 replacement lever arm for all the Von Duprin 88 exit devices. The arm includes the Wedge, Wedge Ring, Wedge Tite Screw and Dog Screw, and sometimes the axle.
Von Dupin part # 050439
Old Part # 10072988R70-As low as $170.00
Von Duprin Exit Device 88 Lever Arm Right Hand
Von Duprin 88 replacement lever arm for all the Von Duprin 88 exit devices. Includes the dog screw, wedge ring, wedge tite screw and wedge, and sometimes they come with the axle
Von Duprin Part # 050438
Old Part # 10074488R80-As low as $170.00
Von Duprin Exit Device 88 Wedge Ring
The Wedge Tite Screw applies pressure on the Wedge which expands the Tube Attaching Ring to grip the Cross Bar. Measures 5/8" on the flat edge.
Von Duprin Part # 090020
Old Part # 95652088R90$6.33
Von Duprin 8827 Top Latch Case for non fire rated doors. This is the part that may be causing your bottom latch to drag on the floor. The Top Latch does all the work on the Von Duprin 8827. When the Top Latch is retracted, it holds the rods in the retracted postion.
Von Duprin part # 050460
Old Part # 10175088VR10$187.86
Von Duprin Exit Device 8827 Center Case88VR120-As low as $320.05
Von Duprin 8827 Bottom Vertical Rod Assembly
This bottom vertical rod is used on non fire rated doors. The rod includes the bottom rod connector.
Von Duprin Part #050455
Old Part #101777 and 10323488VR150-As low as $100.82
Von Duprin 8827 Bottom Latch
Used on all Von Duprin 8827 non fire rated exits. Included mounting screws.
Von Duprin Part # 050461
Old part # 10175188VR170$187.86
Von Duprin 8827 replacement latch covers
Latch covers come with matching screws
Von Duprin Part # 050464
Old Part # 96054888VR30-As low as $75.14
Von Duprin 8827 Top Rod Connector
Inserts into rod so the latch can connect to the rod. The top vertical rod does not ship with the top rod connector!
Von Duprin Part # 050279
Old Part # 96057788VR50$19.00
Von Duprin Exit Device Dogging Spring
Von Duprin dogging assembly part 090041
#3 on diagram
Von Duprin part #090041
The Von Duprin Exit Device Dogging Adaptor Spring 090042 locks the Dogging Adaptor 090043 into the dogging mounting bracket.
Von Duprin dogging assembly part 090042
#2 on diagramG090042$9.75
The Von Duprin Dogging Adaptor is the female part that holds the dogging shaft in place.
Von Duprin dogging assebly part
#1 on diagram
Von Duprin part # 090043
Von Duprin 22, 33 and 99 dogging hook, 090044
#5 on diagram
Von Duprin part # 090044
Von Duprin 5547 Blind Fastener Kit
Connects the rods to the chassis assembly
Includes 2 nuts, 2 bolts 2 washers and 6 screws
Von Duprin Part # 900539G900539$40.36
Von Duprin Strike 248L-4
The Von Duprin 248L-4 Strike is used as a Top Strike on the 2227, 8827, 9927, and 9827 Surface Vertical Rod Panic Devices. The 248L-4 strike measures 9/16" wide by 2-1/2" high with a hole spacing of 1-7/8. The strike projects out 3/8".
Ships with shim and mounting screws
Von Duprin Strike 248L-4
Burnished steel construction248L-4$52.60
Exit Device Dog Key 5/32" X 2-1/8" Long
Used on Von Duprin 55 and 88 Exit Devices, Corbin Russwin Exit Device, Yale Exit Device and Dor-o-Matic exit devices. This Hex Dog Key is not long enough for the Von Duprin 33, 34, 33A, 35B, 98 or 99 Exit Devices.
also known as Hex Key, Dog Key, Allen Key, Dogging Key88R60-SHORT$4.31
Von Duprin Push Bar Guide 090049
Fits on the end of the push bar assembly, reduces noise and friction. Used on the Von Duprin 33A, and 99 / 98's
Von Duprin Part # 090049
Old Von Duprin Part # 971993G090049$15.31
Von Duprin Tail Piece Guide Lead Kit Package Of 10 - 050156
Used to guide rim cylinder tail piece into the back of the Von Duprin 22, 33A, 98, and 99 exit devices
Slot is 5/16" x 3/16" x 1" long
Von Duprin Part # 050156G050156$18.10
Von Duprin Exit Device 992L Hex Stud
This is the Hex Stud used on the 992L Lever Trim and the 991K Knob Trim. The threads are 1/4-20. Overall length is 1-3/4". Later versions of the 992L had a larger thread size.
Von Duprin Part # 971440G971440$12.53
Von Duprin Exit Device Keyed Mullion Retrofit Kit
Keyed Removable Steel Mullions makes removal faster and easier by a single operation of the mortise cylinder. Once mullion is removed, large equipment or furniture can freely pass through the opening. The unit will self lock when re-installed, without use of the cylinder key. Uses a 1-1/4´´mortise cylinder with a
straight cam (Schlage cam reference B502-191). Cylinders are sold separately. Prefix mullion model with “KR”.
Von Duprin Part # 050168KR54As low as $490.92
Von Duprin Exit Device Lever Trim Shear Pin Kit
This is the component that is designed to break, if the lever handle is forced to open , this pin snaps so your trim is not destroyed. 3/16" diameter shaft by 5/8" overall length. Retaining Ring included. This shear pin is used on the 230L, 360L, 992L, 994L and 996L Von Duprin Lever Trims.
Von Duprin Part # 050611 Old Part # 971583G050611$13.00
Von Duprin 7500 Mortise Body Only
This Von Duprin 7500 Mortise Body is used on the Von Durprin 8875, and Von Duprin 98-9975 panic hardware. The body measures 5-7/8" high by 4-1/2" deep and 1" thick. This is the body that has been used since about 1977.
Call or email for pricing on the SS7500, 7500-IN, and E7500 Mortise Bodies and replacement parts for the Lock.
We ship the 7500 in US32D, brushed stainless steel.G7500$555.21
Von Duprin 22, 33, and 9927 Top latch
This latch is used on the 2227, 3327A, and 9927 Surface Vertical Rod Devices. This latch is for use on devices shipped after October 1998. This is usually the problem if your bottom rod is dragging on the floor. Includes screws. The mounting bracket is sometimes included, and sometimes they are not. Call us and we will check.
Von Duprin Part # 050400G050400
Von Duprin Exit Devices 608/880/990TP Thumb Piece
Replace thumb piece only, rivet not included. Cast bronze construction, and then plated to the selected finish. 5-1/8" overall length, but note that the length is usually cut down in the field depending on the thickness of your door.
Von Duprin Part # 970488
Old Part # 960303G970488-As low as $68.19
Von Duprin Exit Devices 608/696/880/990 Trim Grip
Replacement Grip/Handle only, screws not included. Cast bronze construction, and then plated to the selected finish. The Grip measures 15/16" wide by 6" long. The center to center hole spacing is 5-1/2". This handle works on the Von Duprin 608, 696, 880, and 990 outside trim plates.
Von Duprin Part # 972466 and 972467
Old Part # 969925 and 959122G972466-As low as $122.45