Windows

Angle Base 1-3/8" Window Handle

Angle base window is constructed of cast white bronze, and then nickel plated.

Right Hand shown in pictures.

Truth 22.19 Awning Operator

This Truth Awning Operator is usually used on vinyl clad or aluminum windows, and is fastened to the frame by two screws from the rear, which are 7" on center.

Truth Part Number 22.19.xx.212

Roto Casement Operator

This Roto Casement Operator features a hole spacing of 3-1/2" on thee outside mouting holes and 1-7/8" on the two inside mouting holes.  The housing is contructed of die case metal that is electro-statically painted.   The housing is 5-1/2" wide.  The optional handle fits the 5/16" Hex Shaft.

Left Hand Shown in picture

The Truth 50.60 Encore Dyad Operator has been in production since about 1999.   In the beginning Truth offered the Maxim and the Encore Systems.   The Maxim is being phased out and the Encore is the only one made now.   The Encore will replace all of the Maxim operators, and have the same hole spacings and operation, but they have the interchangeable handle and covers.

The Operator in the Picture is a Left Hand.

Window Operator Handing

Window Strike 1/8" Thick Offset

1-3/8" hole spacing x 1/8" thick

white bronze construction with nickel plating

Window Strike 5/32" Thick Inline

1-3/8" hole spacing x 5/32" thick
White bronze construction with nickel plating.

Window Strike 7/32" Thick Inline

1-3/8" hole spacing x 7/32" thick
White bronze construction with nickel plating.

Truth Entrygard 11.42 Awning Operator

Numbers usually found on this operator are 31545

arms measure 12" across when in the closed postition

Truth part # 11.42.00.001

Pella Casement Window Operator

Left hand shown in picture

Truth Window Operator Surface Mount 11"

This Truth Surface Mounted Window Operator is usually used on commercial aluminum windows. It features an 11" long arm, measured from the center of the housing to the center of the metal roller. The outside mounting screw holes are 4-3/4" a part and the inter screws are 3-7/8" on center.

Right Hand Shown, in Aluminum

Right Hand Aluminum Wi36223AL
Left Hand Aluminum Wi36222AL
Right Hand Bronze Wi36223BR
Left Hand Bronze Wi36222BR
Right Hand White Wi36223W
Left Hand White Wi36222W

Truth Universal With Pole Hook 30325

Use to convert elevated windows and skylights for use with the Pole Wi10638

Truth part # 30325

Truth Manual Skylight Sprocket Gear

The hex measures 3/4", and made of 1/8" cadmium plated steel. This Gear is what pushes the chain.

Truth Part # 30654

Truth 22.17 Awning Window Operator

Surface mounted Truth Awning Window Operator.  The arms span 13-1/4” from rivet to rivet.  The mounting holes measure 6-7/8” on the outside screws center to center, and 6” center to center on the two inside mounting screws.

Truth Part # 22.17

Defender Window Hinge 10” Sold in Pairs

This hinge is used on aluminum, vinyl and wood windows.  They are fitted with a unique plastic raiser block which guarantees a sure fit.  This hinge is 10” long,  has a 1/2” stack height and measures 11/16” wide and is constructed of Stainless Steel.  We sometimes see Securistyle or made in the UK stamped on the hinge.

Truth 12511 Right Hand Bracket

This bracket is usually used with Truth Split Arm or Dyad Operators.

Truth 21088 Casement Window Keeper

This Truth Window Casement Strike is 4-5/8" long and made of stamped steel.

Angle Base 1-3/8" Window Handle-1/4" Drop

Cast white bronze with a brushed nickel finish

Truth Replacement Clip.

Used on Truth operators and hinges

Acorn Sweep Lock 2-1/4"

This sweep latch has a hole spaceing of 2-1/4" between screws. Also known as a Window Lock or Double Hung Window Lock. Acorn Sweep Lock.

White only

A.W. Anderberg 301AL 4 Bar Window HInge, aluminum construction.

29/32" width x 5/8" stack height

Found in commercial aluminum framed hopper windows.

10" and 12" only, if you have an older larger size, please use the A.W. Anderberg 301ST or A.W. Anderberg 301SS as a replacement. You might have to shim the tracks in these cases, because the stack height is lower on the steel and stainless steel hinges. A.W. Anderberg no longer makes the larger sizes of the Aluminum Hinges due to the brittle nature of aluminum.

Sold individually, we recommend changing both hinges with you are replacing the hinge.

6-20-2012 No longer manufactured, what we have in stock, is what we have. You will have to replace with 301ST or 301SS Hinges

A.W. Anderberg 201ST 4 bar window hinge, cadmium plated steel construction.

Usually found on light commercial or residential buildings with hopper windows. This hinge is being discontinued, and replaced by the 201SS Hinge, which has the same hole spacing, length, and stack height.

23/32" track width x 1/2" stack height.

If you have a casement window with a 16" track length, please see 222SS Egress Window Hinge.

Sold individually, these hinges are non handed, we recommend that you change both hinges when you are replacing them.

85 Series Tube Balances, 5/8" Diameter.

This is the most common type of tube balance out there.

Truth Universal 30326

Female hex on one end, with the Truth female 11/32" spline.

Truth Celestory Pole Crank

Rigid aluminum tubing with flex cable inside. Recommended height range for floor 8' to 11', windows only!

Truth Window Bracket 10553

This bracket is usually used on the Truth split arm operators

Truth Entrygard Dual Arm Operator. We would expect you to find 20810 on the linkage arm, which measures 4-7/16" overall length. This is the most common size we find in use. Other common numbers we would expect to find are 31538, 31539, 30841, 30842, 30472, 30470, 20810, or 20544. Also known as a TH-23076 or TH-23077.

4-7/16" link dimension, offset up. For offset down, order Wi1561.

Order Wi1516 if your link dimension is 3-3/4" stamped 20755.
Order Wi1515 if your link dimension is 2-7/8" stamped 20748.

MOST POPULAR SIZE

To determine hand of operator, if your sash lock (window lock), is on the left, you would use a left hand operator. And if your sash lock is on the right, you would order the right hand operator.

PART # HAND
WI1510R RIGHT HAND
WI1510L LEFT HAND

Truth Entrygard Dual Arm Operator

Truth Entrygard Dyad Window Operator.

Common numbers found on this operator are 30636, 30637, and 20544 for the old style,
31368, 20810, and 45275 for the new style.  Call or email for quantity "Discount Codes".

For link off-set up version order Wi1562

See attached file of what the Original Version looked like

Left hand shown.

Truth Entrygard Dual Arm Operator. We would expect you to find 20810 or 20544 on the linkage arm, which measures 4-7/16" overall length. This is the most common size we find in use. Other common numbers we would expect to find are 31538, 31539, 30841, 30842, 30472, 30470, 20810, or 20544.  Call or email for quantity "Discount Codes".

For offset up, order Wi1510.

To determine hand of operator, if your sash lock (window lock), is on the left, you would use a left hand operator. And if your sash lock is on the right, you would order the right hand operator.

Part # Hand
WI1561R Right Hand
WI1561L Left Hand

Truth Entrygard Dual Arm Operator

Common numbers found on the older version of this operator are 40575 for the right hand operator, and 40574 for the left hand operator

To determine hand of operator, if your sash lock (window lock), is on the left, you would use a left hand operator. And if your sash lock is on the right, you would order the right hand operator.

Left hand shown.

Truth 23.03 Single Arm Operator

13-1/2" Arm length, Front Mounting, Ships with matching handle.

Truth 52.01 Maxim Single Arm Window Operator. Manufactured since 1999. Ships with matching handle.

Truth 10.10 Lever Operated Awning Window Operator.

Less than 2" projection.

Attaches to window at one point.

Includes sash hook.

Truth 10.10 Lever Operated Awning Window Operator.

More than 2" projection.

Attaches to window at one point.

Includes sash hook.

Truth 10.11 Lever Operator Awning window operator.

Handle assembly projects more than 2"

Truth 13.16 Awning Window Hinge.

Sold in Pairs