Door Hardware

2-1/4" knob pinned to a straight spindle. The inside kob is attached
with two case hardened set screws. 3/8-20 tread on knob and spindle.

Install A Lock Cylindrical

Repair and reinforce existing doors with this wrap around trim. A great way to repair doors that have been pried or forced open. Select your back set, the distance from the edge of the door to the center of the bore, door thickness, and color. Available in Stainless Steel, and Polished Brass.

2-1/8" bore x 9" tall x 4-1/4" wide.

Zipper Pile Weatherstrip .270" Backing - .300" Pile Height - 100' Roll

Replaces Old or Worn-Out Pile Weatherstripping in Doors and Windows. New Zipper Tooth Design Allows Pile to Easily Snap in from Above the Extrusion Slot. High Density Gray Pile with Double Center Fin.

• Use with 7212, 7212V or 7222 3/4 Offset Pivot
• Handed
• Vertical adjustment 3/16", include positive locking.

Handing diagram

Standard duty brass 2-1/4" knob is pinned to swivel spindle for 1-3/4" door.
Outside spindle is 3/8" solid center and inside spindle is 9/32". Inside knob
threaded 3/8-20 with two case hardened set screws.

Install A Lock Lock And Deadbolt

Repair and reinforce existing doors with this wrap around trim. A great way to repair doors that have been pried or forced open. Select your back set, the distance from the edge of the door to the center of the bore, door thickness, and color.

2-1/8" holes with 3-5/8" centers

• Handed
• Top, header mount
• Bottom, base plate mount
• Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
• Maximum door load 200 pounds
• Vertical adjustment range 3/16", with positive locking

Handing diagram

Heavy duty knob set. Replaces the Corbin #1419 with #32 spindle.
Outside knob is pinned to spindle and inside knob is held by
two 5/16" case hardened set screws. Spindle is on 3/8" diameter
center on outside half and inside spindle is threaded 3/8-20

• Use with 7212, 7212V or 7222 3/4 Offset Pivot
• Handed
• Vertical adjustment 3/16", include positive locking.

Handing diagram

Swivel spindle, 4-3/4" long,
plain centers, 20 tpi

Install A Lock Deadbolt

Repair and reinforce existing doors with this wrap around trim. A great way to repair doors that have been pried or forced open. Select your back set, the distance from the edge of the door to the center of the bore, door thickness, and color.

2-1/8" bore x 4-1/2" tall x 4-1/4" wide.

Swivel spindle, 9/32" square,
18 tpi, 4-3/4" long with two 3/8" solid centers

Swivel spindle, 9/32" square,
18 tpi, 4-3/4" long with two 3/8" solid centers
and three pinning holes

Standard duty 2-1/4" knob is factory pinned to swivel spindle
to 1-3/4" door. Spindle has two 3/8" centers. Inside knob has
two case hardened set screws and spindle is threaded 3/8-18

3-1/2" straight spindle thread is 18 tpi. 2-1/4" knob

2-1/4" knob pinned to a straight spindle. The inside kob is attached
with two case hardened set screws. 3/8-18 tread on knob and spindle.

Swivel spindle, 4-3/4" long
Two 3/8" solid centers
20 tpi

Reinforcing Pivot Hinge 4" - for use with a 4" wide butt hinge

1/2" to center line of 4" hinge.
Used to strengthen and reduce vibration
to your current full mortise butt hinges.
Made of Zinc Plated Steel

These hinges are not longer handed. Please select hand when checking out, until our system is updated.

4-3/4" long
9/32" square
16 tpi

Reinforcing Pivot Hinge - For use with 4-1/2" wide butt hinges

3/4" to center line of 4-1/2" hinge pin.
Pin uses large pin and bushing.
Used to dampen vibration and increase
strength to your full mortise butt hinges.
Constructed of heavy duty cold rolled steel.
Made of Zinc Plated Steel
Supports weights up to 300 lbs

Manufacturer part # B1923
Our part # DR1923 for Right Hand, DL1923 for Left Hand

These hinges are no longer handed, you can select right or left, but the hinges will work both ways.

Swivel, 9/32" square,
16 tpi, 4-3/4" long,
with stop pin

The reinforcing pivot hinge is a good way to solve door sag issues. And also be a preventative solutions for future isses with extra heavy or wide doors. The hinges comes in two sizes 4 or 4.5 inches, and two finishes, prime coat and satin chrome. The hinge uses a heavy duty ball-bearing to add extra life.  The base metal is steel.

Swivel spindle
9/32" square, 16 tpi
4-3/4" long, w/ two solid centers

Sargent inside/outside spindle

8100 Series rec'g prior to 1/1/1990

includes lever bushings, roll pin and set screws

Replacement spindle for the 8100 series, January 1990 to current.

Includes lever bushings, roll pin and set screws