Generic
-
Stamped SS Keeper For 3/4" Door, 1-7/8" Between Screws
Partition Strike And Keeper For 3/4" Door, 1-7/8" Between Screws Stamped Stainless Steel
Stamped stainless steel .075" thick construction. The strike and keeper measure 2-7/8" high by 2" wide with a 1-7/8" hole spacing. The stop posts are 5/8" wide by 7/8" tall with rubber inserts. For use with 3/4" square edge posts. Also known as a Bathroom Stall Strike and Keeper Outswing 3/4". Manufacture part # 6379.
Shipped with mounting screws.
9A6379 -
Stamped SS Keeper In swing 1-7/8 & Bet Screws
Toilet Partition Keeper For Inswing Doors 1-7/8" Between Screws Stainless Steel
14 gauge (.075" thick) stainless steel construction. Keeper is 2-7/8" high x 1-13/16" wide with 1-7/8" hole spacing. Lip is 9/16" and the slot or cut out is 7/32" x 1". Also known as Bathroom Stall Keeper Inswing. Manufacture part # 6319.
Shipped with screws.
9A7056 -
Double Prong Locker Hook
Double prong ceiling hooks are mounted to the inside top of a locker to hang a jacket, hat or other items. The locker hook is made of steel wire then zinc plated for a shiny finish 3/16" diameter. The dimensions top to bottom are 2-5/16" and 3-5/8" overall width. Between hole spacing is 1/2"-1" slot. Also known as 91001, 9005, 81007, bu0112, lu125.
200197 -
Chrome Plated Keeper Bumper For 1-1/4" Outswing Round Edge
Chrome Plated Keeper Bumper For 1-1/4" Outswing Round Edge Post
Zamac die cast and polished chrome plate construction. The strike and keeper measure 2-1/2" high by 1-7/8" wide with a hole spacing of 1-1/2" on center. The stop is 2-1/2" tall by 3/4" wide with a rubber insert. Commonly known as a Bathrrom Stall Strike and Keeper Outswing 1-1/4". Manufacture part # 5410
Shipped with mounting screws.
9G015E -
Chrome Plated Keeper Bumper For 1-1/4" Inswing Round Edge
Chrome Plated Keeper Bumper For 1-1/4" Inswing Round Edge Post
Zamac die cast and polished chrome plate construction. The strike and keeper measure 2-1/2" high by 1-7/8" wide with a hole spacing of 1-1/2" on center. The stop is 2-1/2" tall by 3/4" wide with a rubber insert. The slot measures 1-9/16" high by 5/16" deep. Commonly known as a Bathrrom Stall Strike and Keeper Inswing 1-1/4". Manufacture part # 5310
Shipped with mounting screws.
9G0151 -
-
-
-
-
Locker Number Tags, 1-3/4" Hole Spacing
Locker Number Plates fits most lockers except Lyon. Make sure to add what numbers you are looking for. 1-600 in stock. Pop rivets included. Overall size 2-5/16" x 1-1/16". Manufactured in the USA. Also known as 99001, 70072, bu0110, lu122. Hole spacing 1-3/4".
Note: Blank number plates are available and in stock, with no numbers on them. Each number plate you need is quantity one. Ten plates equal qty 10 for ordering.
*** Note we only sell 1-600, no special orders. ***
#PLATES -
7/8" Q-Ball Floor Protector with Felt Base
7/8" Q-Ball Floor Protector with Felt Base for use on 7/8" outside diameter chair and table legs.The adaptor shown on the right fits over your existing glide, and then the Q-Ball slides over the adaptor. Constructed of Gray Plastic. Kit includes: Adaptor for 7/8" Leg, and Q-Ball with Felt Base
CGQ87F -
7/8" Q-Ball Floor Protector
The 7/8" Q-Ball Floor Protector is for use on 7/8" outside diameter chair and table legs. The adapter shown on the right fits over your existing glide, and then the Q-Ball slides over the adapter. Constructed of Gray Plastic.
CGQ87 -
3/4" Q-Ball Floor Protector with Felt Base
The 3/4" Q-Ball Floor Protector with Felt Base is for use on 3/4" outside diameter chair and table legs. The adaptor shown on the right fits over your existing glide, and then the Q-Ball slides over the adaptor. Constructed of Gray Plastic. Kit includes: Adaptor for 3/4" Leg, and Q-Ball with Felt Base
CGQ75F -
3/4" Q-Ball Floor Protector
The 3/4" Q-Ball Floor Protector is for use on 3/4" outside diameter chair and table legs. The adaptor shown on the right fits over your existing glide, and then the Q-Ball slides over the adaptor. Constructed of Gray Plastic.
CGQ75 -
5/8" Q-Ball Floor Protector with Felt Base
The 5/8" Q-Ball Floor Protector with Felt Base is for use on 5/8" outside diameter chair and table legs. The adaptor shown on the right fits over your existing glide, and then the Q-Ball slides over the adaptor. Constructed of Gray Plastic. Kit includes: Adaptor for 5/8" Leg, and Q-Ball with Felt Base.CGQ62F -
5/8" Q-Ball Floor Protector
The 5/8" Q-Ball Floor Protector is for use on 5/8" outside diameter chair and table legs. The adaptor shown on the right fits over your existing glide, and then the Q-Ball slides over the adaptor. Constructed of Gray Plastic.
CGQ62 -
1-1/8" Q-Ball Floor Protector
The 1-1/8" Q-Ball Floor Protector is for use on 1-1/8" outside diameter chair and table legs. The adaptor shown on the right fits over your existing glide, and then the Q-Ball slides over the adaptor. Constructed of Gray Plastic.
CGQ112 -
1" Q-Ball Floor Protector with Felt Base
1" Q-Ball Floor Protector with Felt Base
The 1" Q-Ball Floor Protector with Felt Base is for use on 1" outside diameter chair and table legs. The adaptor shown on the right fits over your existing glide, and then the Q-Ball slides over the adaptor. Constructed of Gray Plastic.
Kit includes: Adaptor for 1" Leg, and Q-Ball with Felt Base
CGQ100F -
1" Q-Ball Floor Protector
The 1" Q-Ball Floor Protector is for use on 1" outside diameter chair and table legs. The adapter shown on the right fits over your existing glide, and then the Q-Ball slides over the adapter. Constructed of Gray Plastic.
CGQ100 -
-
-