Search results for: 'screen door hardware latch steel last chair unit'

International Door Closer 522 Hold Open Arm

This is the New Style Hold Open Arm from International Door Closer. In July of 2014, the old style was discontinued. Look under "More Views" to see the Old Style. Shown in Dark Bronze, ships with all components in the picture.

International part # 522

International Door Closer 3020-VO Arm and Track

International Door Closer 3020-VO Arm and Track for Offset Top Arm Assembly Mortised Type (7/8" Depth of Top Rail). Track measures 12-5/8" long by 1/2" high by 1-1/4" wide.

International Door Closer 3010-DP Bottom Pivot

Adjustable dual purpose bottom pivot set

International Part # 3010-DP

Door Sweep 1" Long Rubber

Extruded aluminum rail with a 1" gray rubber seal. Available in aluminum or dark bronze. Screws included.

International Part # IDC-97V

International Door Closer 3010-K Arm

International Door Closer 3010-K Arm, K type end loading top arm assembly (5/8" depth top rail). All screws included with package.

International Door Closer 3010-JO Arm and Track

International Door Closer 3010-JO Arm and Track for Offset Top Arm Assembly Mortised Type (9/16" Depth of Top Rail). Track measures 15-1/4" long by 3/4" high by 15/16" wide.

International Door Closer 525 PA Bracket

International Door Closer 300 Series Adjustable Power

UL Listed, Barrier Free Operation to Comply with Federal Accessibility Standards (ADA) ANSI A117.1.   Spring Power adjustable for a range of sizes from 8-1/2 lbs t Medium Spring Tension, fully adjustable after installation.

Hydraulic Cylinder only

3000-B-310 105 with Hold Open
3000-B-311 105 with No Hold Open
3000-B-312 90 with Hold Open
3000-B-313 90 with No Hold Open

The International Door Closer 3010-S Side Load Arm is used with the 200, 300 and 500 Series Concealed Overhead Door Closer for Center Hung Doors.   The arm is constructed of cast iron and measures 10" long, and 7/16" thick.   The package includes all the mounting screws.

International Door Closer T1 Push Pull Mounting Screw is used PH-4000, PB-2000, and PP-2000.  The screw measures 2-9/16 inches long, with a 3/8 inch diameter and 18 threads per inch.

International Door Closer T5 Push Pull Back to Back Mounting Screw is used on the PB-2000, PP-2000 and the PH-4000. Overall length is 3-3/16 inches including the head, and has a 3/8 inch diameter. The head has a 7/16 diameter and stick out 5/8 inches.

International 521 Forearm

Arm measures 9-1/2" loop to loop in the shortest position, and 14" when it is the fully extended . The loop on the left side is 3/8" diameter. The hole spacing on the right hand side of the picture shoe is 1-3/4".

International part # 521

Intermediate Hinge IP-1901 and IP-1902

Cast aluminum construction with steel bearings. The hinge measures 5" high by 2-1/2" wide. This hinge has a 3/4" offset. We find this hinge in the middle section of the door between the top and bottom hinges. Available in the Aluminum color and Dark Brown. See the dimensional information under more views.

Manufacture Part # IP-1901 and IP-1902
IP-1901 is for Left Hand Doors
IP-1902 is for Right Hand Doors

Intermediate Hinge IP-2202 and IP-2201

Cast aluminum construction with steel bearings and axle. The set measures 3-1/2" tall with an 1-3/8" projection. This hinge is usually used an an intermediate hinge in between the top and bottom hinge.

Manufacture part # IP-2202 and IP-2201
IP-2202 is for Right Hand Doors
IP-2201 is for Left Hand Doors

The International Flushbolt Standard Guide is the piece that fits into the top or bottom of the door and acts as a guide for the Flushbolt Rod.  The piece measures 1-3/8" x 1-1/2".  The square hole in the piece is a 1/2" square.  The manufacture part number is FG-1200.

Plunger Type Holder / Stop DH6000

Zinc Alloy Construction
Non-Marking Rubber Tip
7" Body Height
1.142" throw
Mounting Screws Included
Made by International Door Closer

Aluminum Store Front Door Flush Bolt FB-1202

15/16" x 4-1/4" radius face, 5-7/32" hole spacing, 1/8" offset, 5/8" throw, 12" rod length, with a square nylon tip with beveled corners fits in a 1/2" square hole.

Rubber Shoe for DH6000

Replacement rubber shoe for the GDH6000

The International 8600 Dogging Assembly is used on the 8510S, 8710S, 8610S, 8810S, 8501S, 8710S, and many more.

One inch diameter solid push bar, 2-1/4 inch projection with 1-1/4 inch clearance and 33-1/16 inch centers.  One side is thru bolted the other is mounted on a surface mounted stud.

Sex Nut 1/4-20

1-3/4" Long X 3/8" diameter constructed of aluminum

screw not included