Search results for: 'covers latch tread toilet acrylic stem t'
-
775 Epoxy Flooring Adhesive
775 EPOXY FLOORING ADHESIVE
The only recommended adhesive for use with Disc-O-Tile. May be used with other rubber stair treads, tile and flooring. Because of flame spread properties, other adhesives will not bond Disc-O-Tile to the floor. A two-part solvent-free adhesive; contains 1 can Part A 1 can Part B, and a stirring paddle. Covers approximately 150 square feet per unit. Enviromental Friendly!
775EPOXY- -
KT18 Vinyl Landing Tiles
KT18 Vinyl Landing Tiles
Landing tiles are .120" thick by 18" x 18" and designed to go with all the vinyl stair treads. Available colors are Shale and Amber. Shale is for use with the Black and Gray treads, and the Amber is for use with the Brown or Sand color treads.
KT18- -
Fluff-Cord Tile Adhesive
Adhesive specifically designed for the TT-12 Fluff Cord Tile.
1 gallon covers approximately 100 square feet
TT390 -
GSA3 Grit Strip Adhesive
Use adhesive where Grit Strip is applied to porous surfaces such as wood or concrete. Grit Strip adhesive is recommended as a sealer; will give a better, longer lasting bond. Recommended application temperature is 60 degrees and above. One quart covers approximately 50 square feet (single coat) of Grit Strip; available in quart and pint units.
GSA3 -
320 Carpet Tile Adhesive
320 CARPET TILE ADHESVIE
A special latex emulsion pressure sensitive adhesive formulated for installation of modular carpet tiles or carpet matting. Adhesive is non-flammable, water resistant and has excellent resistance to vinyl plasticizer migration. Adhesive remains tacky for an extended period - allows tile to be picked up and replaced without affecting adhesive. Remove tiles from floor more easily than with conventional adhesives, simplifying reinstallation of tile sections or a complete area.
Covers 200 to 300 square feet per gallon
Sold in 1 or 4 Gallon Pails320ADH -
Aluminum Nosing 2 inch with Grit Surface
This 2-1/2" deep nosing is made from the same material as our Grit-Surface Aluminum Treads. The front edge is 1-3/4" deep (inside nose dimension is 1-1/4"). The nose has a 1-3/4" wide abrasive finish with a 3/4" tapered aluminum back edge. Both the nose and tapered edge have a 1/4" wide reflective yellow safety tape strip for additional safety. The nosing is available in abrasive colors of Black, Brown, Blue, Gray, Green, Red or Yellow. Nosing is available solid (for glue-down applications) or with countersunk holes (for screw-down applications) every 12". Nose drops 1-1/16".
SPECIFICATIONS:
Furnish and install Musson Grit-Surface Aluminum Nosings, 3/16" thick X 2-1/2" deep; cut lengths up to 10 foot long. Tread surface shall have aluminum oxide abrasives permanently bonded to a heat treated aluminum nosing with 1/4" wide reflective yellow safety strip on both the top surface (between the grit surface and aluminum) and the nose. Grit surface shall be in one of the following standard colors: Black, Brown, Blue, Gray, Green, Red or Yellow. Nosings can be supplied with two countersunk holes every 12" for screw down installation or without holes for installation with our #400 Neoprene Contact Cement.
Custom sizes are available up to 10' long
GSA2N- -
Berber Tiles BT-220 Entrance Mat
BERBER TILES BT-220 ENTRANCE MAT
A heavy-duty, 40-oz./sq. yard needlepunch olefin tile that "breathes" so that moisture evaporates quickly. This 3/8" x 19-11/16" x 19-11/16" tile with a bitumen backing will not shrink or curl. The berber texture offers all the advantages of a heavy-duty wiper/ scraper with a custom carpet look.
Sold in cartons only of 12 tiles, enough to cover 32.3 square feet
See Color Chart under "More Views"
BT220 -
DR-CT Diagonal Rib Carpet Tiles
DR-CT DIAGONAL RIB CARPET TILES
An attractive and functional entrance matting alternative; heavy duty modular carpet tile with excellent scraping and dirt removal properties for high traffic areas. Designed for interior use in entrances, vestibules, lobbies, between double doors, on ramps or in elevators.Install in a recess or on the surface. Our easy release adhesive allows you to remove worn or damaged tile which is easily re-adhered. Tile can be switched to decrease traffic patterns; lasts longer, looks better. Vinyl or Aluminum beveled edging available.
3/8" thick; 19-11/16" x 19-11/16" square tile; diagonal rib pattern woven of 100% polypropylene pile yarn with a bitumen backing.
SPECIFICATIONS--No. DR-CT
DR-CT Diagonal Rib Carpet Tiles made of 100% polypropylene pile yarn with a bitumen backing in areas as indicated on drawings. Tile shall be of first quality commercial grade carpet, free of surface defects. Install tile in an alternating rib parquet pattern in indicated recess with recommended easy release adhesive, (or on surface area using vinyl edging or aluminum beveled frame). Tile shall be 3/8" thick, 19-11/16" x 19-11/16" square carpet tile. Select from standard carpet colors of Cranberry, Blue, Beige, Teal, Gray, Chocolate or Charcoal.
one DR-CT Diagonal Rib Carpet Tile covers 2.69 square feet
DR-CT
