Search results for: 'green 8 door bronz door hager'

Von Duprin 360L Lever Trim

The Von Durpin 360L Lever Trim has a base measurement of 7-1/2" high by 1-11/16" wide and 7/8" thick. The lever is 4-1/2" and projects out 3". This lever Trim uses a 1-1/4" Mortise Straight Cam Cylinder.

Von Duprin Part # 360L

The Von Duprin 090039 is used in the push bar assembly to return the latch. It is known as the Base Plate Latch Return Spring or Latch Return Spring. It is used on the 22, 33A, 35A, 98 and 99 Devices. The spring is 2-1/4 inch long with a 3/8 inch diameter.

Von Duprin Strike 385A

The Von Duprin 385A Strike is used on the floor for the Von Duprin 2227, 8827, 9827 and 9927 Surface Vertical Rods. The strike face plate outside dimensions are 2-1/4" x 2-1/4" with an inside dimension of 1-1/8" by 1". This floor strike features a bolt that can be cemented into the floor. Zinc plated finish.

Von Duprin 7500 Mortise Body Only

This Von Duprin 7500 Mortise Body is used on the Von Durprin 8875, and Von Duprin 98-9975 panic hardware. The body measures 5-7/8" high by 4-1/2" deep and 1" thick. This is the body that has been used since about 1977.

Call or email for pricing on the SS7500, 7500-IN, and E7500 Mortise Bodies and replacement parts for the Lock.

We ship the 7500 in US32D, brushed stainless steel.

Von Duprin Exit Device Lever Trim Shear Pin Kit

This is the component that is designed to break, if the lever handle is forced to open , this pin snaps so your trim is not destroyed. 3/16" diameter shaft by 5/8" overall length. Retaining Ring included.  This shear pin is used on the 230L, 360L, 992L, 994L and 996L Von Duprin Lever Trims.

Von Duprin Part # 050611 Old Part # 971583

Von Duprin 8827 Special Chassis Nut 050277

The 8827 Special Chassis Nut goes on the ends of the 8827 Chassis Tie Rod. The Nut is threaded all the way through so the cover mounting screws can then be threaded on it also. The nut is 3/8" long by 1/4" hex.

Von Duprin Part # 050277
Old Von Duprin Part # 960652

Von Duprin Aluminum Mullion 5654 7'2"

The Von Duprin Aluminum Mullion 5654 comes prepped for two of the 299 Strikes.  Everything is included, except the the 299 strikes.

Von Duprin 1654-4954 Mullion Brackets

Top and bottom mullion fittings. Von Duprin part # 050330. Includes everything shown in diagram

Von Duprin 1654/4954 Top Mullion Fitting and Cover

Replacement Top Mullion fitting for the Von Duprin 1654 and 4954 Removable Mullions.

Von Duprin Part # 050335 

The Von Duprin 98/99 Maintenance Kit includes all the parts and pieces you need to keep your 98 or 99 device running properly for years.  If you are interested we can email a list of the parts.

Von Duprin part # 050046

98/99 Maintenance Kit Instruction Manual

Von Duprin 8827 Rod Guide Assembly

Securely holds rod in place and protects rod from bending.

Von Duprin Part # 050482
Old Part # 101648

The Von Duprin 33/99 Cylinder Dogging Conversion Kit 050155

Converts the Hex Key Dogging 33A and 99 Devices to Cylinder Dogging.  The kit does not include the key cylinder, which is a Mortise Cylinder.

Von Duprin Part # 050155

Von Duprin 88 and 55 Wedge Tite Screw.

This screw applies pressure to the wedge which then expands the wedge ring to key the Von Duprin 88 and 55's crossbars tite.

Von Duprin Part # 090081