Search results for: '1 4 2001 nylon brass shoe'

Sled Base Felt Stem Glide with a 1/4" insert diameter. The base diameter is 7/8" and the Stem Length is 1/2". This glide works on any diameter sled base chair. This glide gently taps into 1/4" hole on the bottom side of a sled leg. Felt bottom to help protect floors. 

The 459 Flush Door Pull measures 3-3/8 x 4-3/4 x 1/8 inch.  The opening size is 1-3/4 by 3-1/2 inches.  The mortised pocket would need to be 3-3/4 by 2-13/16 and 11/16 deep. The flush pull ships with mounting screws in the matching finish.

Toilet Partition Two Ear Wall Bracket For 3/4" Thick Panel Stamped Stainless Steel

14 gauge (.075" thick) stamped stainless steel construction. Base is 1-1/2" x 3-13/32" with the mounting screws are 2-21/32" on center. Leg project out 2-1/2" with the thru hole at 2-1/8" from the base. Also known as a Bathroom Stall Wall Bracket and Two Wing Bracket. Manufacturer part # 1629.

Shipped with screws

Toilet Partition Continuous One Ear Wall Bracket For 1" Panel Aluminum

Constructed of extruded anodized aluminum. Base is 2-5/8" wide by 57-1/2" long, with screw holes every 13" or so. The legs project out 2-3/4" with the thru hole at 2-3/8" from the back of the base. The legs have a clearance of 3/4" for 3/4" thick panels. Sometimes known as Bathroom Stall Continuous One Ear Wall Bracket. The manufacturers part numbers are 650-4031. These brackets are shipped with all the needed fasteners.

Von Duprin 880TP Trim

The plate measures 3" wide by 14-3/16" long with an 1-5/8" bore hole for cylinder.

Von Duprin part # 880TP-R

Chrome Plated U Bracket For 3/4" X 1-1/2" X 1-3/8. If your toilet partition or bathroom stall wall bracket is cast with the number 1890 on the back, then you have the U Bracket for 3/4″ thick toilet partition panels. The wall bracket is usually mounted on the wall or the pilaster to mount the toilet partition stall panels. This bracket is 1″ wide x 1-3/8″ tall, with the through hole located at 1″ from the back. If features 4 holes with a 1/4″ diameter, with two of them on the base. The bracket is made of a die cast material that is then polished chrome plated. This bracket is sometimes called a Toilet Partition or Bathroom Stall U Bracket, or “U” Wall Bracket.

Toilet Partition Bracket Two Ear For 1" Thick Panel Aluminum

Constructed of extruded anodized aluminum. Base is 3" high by 3-3/4" wide with the mounting holes 2-3/4" on center. The legs project out 2-3/4" with the thru hole at 2-3/8" from the back of the base. The 8 holes are 1/4" diameter. All wall thicknesses are 1/8". This bracket is sometimes known as a Bathroom Stall Two Ear Wall Bracket, or Toilet Partition Two Ear Wall Bracket. The manufacturers part number is 2264 and 650-1839. This bracket ships with all the needed fasteners.

Toilet Partition One Ear Hinged Wall Bracket 1-1/4"

Hinge is 16 ga (.060") thick, Bracket is 14 ga (.075") thick. The one ear hinged bracket is Riveted and welded together. Bracket is 3" high x 2-1/2" deep for a 1-1/4" panel. This bracket is ideal for applications were the Pilaster and Panels are not at a 90 degree angle. Also known as a Bathroom Stall HInged Wall Bracket. Manufacture part # 111369

Non-Swivel Leveler Threaded Stem Glide with metal base. Thread is 1/4-20, Base Diameter is 1 1/16" and the stem length is 1". This glide screws into a 1/4" threaded leg hole to put a selected height. Use this product to stop wobbling on an uneven floor. 

Friction Ring Plastic Inserts For Round Legs with a 7/16" diameter friction ring casters only. 

Tubing Inside diameter / Part #'s

5/8" KK5A31
3/4" KK5A32
7/8" KK5A34
15/16" KK5A35
1" KK5A36
1-1/16" KK5A37
1-1/8" KK5A38

Push Plate 60

8" x 16" x .050

Finishes

Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.

Pro-Rite® Markers

4 Markers and 1 eraser

American Sanitary Pintle 5/8" Diameter

Steel and white nylon construction. The Pintle is 5/8" diameter by 2-1/4" overall length with 5/16-18 threaded end. Also known as a Bathroom Stall Bottom Pintle 5/8" Medium Lift. Manufacture part # 98175.

Shipped with nut and lock washer.

Toilet Partition SS Continuous Hinge 57" With Spring Close. Rh In, Lh Outswing

14 Gauge,1/4" Pin. 9" centers with 6 holes on each side.

Coat Hook & Bumper 3-1/2" Projection x 2-3/4" High Chrome Plated

Chrome plated Zamac construction. Coat hook base is 1-1/2" wide by 2-3/4" high, with screw spacing of 7/8" at the top. Hook projects out 1". Bumper projects out 3-1/2" with a rubber insert. Also known as a Bathroom Stall Coat Hook and Bumper. Manufacture part # 4260.

Same as 9OT285, 9HA426

Corner Guard 310

Fabricated from B & S 16 ga. (.050). Standard lengths are 36", 42" and 48". Custom capabilities include variations of all of the above parts including frame protectors and vertical rod protectors.

3-1/2" x 3-1/2" x 48"
Custom sizes are available!

Screws included for mounting

Please allow 1 week shipping time

Finishes

Jack Nut 1/4-20

The Jack Nut is used on hollow metal doors to fasten door closers, door closer arms, exit devices and continuous hinges.

Threaded stem metal base glide, thread is 1/4-20, base diameter 1 1/6", and stem length is 1/2". Glide is furnished with nut.  This non swivel leveler stops wobbling on uneven floors. 

Fenestra Casement Operator

The arm is 9" long and the outside screw spacing is 5-1/4". The inside threaded holes are 4-1/4" apart. Die cast construction with steel arm. Ships with handle and mounting screws.

Reinforcing Pivot Hinge - For use with 4-1/2" wide butt hinges

3/4" to center line of 4-1/2" hinge pin.
Pin uses large pin and bushing.
Used to dampen vibration and increase
strength to your full mortise butt hinges.
Constructed of heavy duty cold rolled steel.
Made of Zinc Plated Steel
Supports weights up to 300 lbs

Manufacturer part # B1923
Our part # DR1923 for Right Hand, DL1923 for Left Hand

These hinges are no longer handed, you can select right or left, but the hinges will work both ways.

Single Hook Chrome Plated Projects 1-3/4", also known as UC10.

Bleacher Bolt Fastener Whiz nut 1/4-28.

Partition Continuous One Ear Wall Bracket For 1"Panel Aluminum

Constructed of extruded anodized aluminum. Base is 2-5/8" wide by 57-1/2" long, with screw holes every 13" or so. The legs project out 2-3/4" with the thru hole at 2-3/8" from the back of the base. The legs have a clearance of 1" for 1" thick panels. Sometimes known as Bathroom Stall Continuous One Ear Wall Bracket. The manufacturers part numbers are 2334, one ear 1" x 57, and 650-9750-58. These brackets are shipped with all the needed fasteners.

Alcove Two Ear Bracket Panel Kit for 1/4" Offset. This kit is used for panel to pilaster 1/4" offset and for 1" panel to wall bracket chrome plated. Security screws included. Also known as 615330.

Friction Ring Plastic Inserts For Square Chair Legs for 7/16" diameter friction ring casters only. 

Tubing Inside diameter / Part #'s

5/8" KK5A41
3/4" KK5A42
7/8" KK5A44
1" KK5A46
1-1/8" KK5A48

Fiat Partitions Pintle 5/8" Diameter For Steel Doors

Steel and white nylon construction. The Pintle is 5/8" diameter by 2-1/4" overall length with 5/16-18 threaded end. Also known as a Bathroom Stall Bottom Pintle 5/8" Medium Lift. Manufacture part # 98175.

Shipped with nut and lock washer.

Global Partitions Pintle 5/8" Diameter For Steel Doors

Steel and white nylon construction. The Pintle is 5/8" diameter by 2-1/4" overall length with 5/16-18 threaded end. Also known as a Bathroom Stall Bottom Pintle 5/8" Medium Lift. Manufacture part # 98175.

Shipped with nut and lock washer.

Toilet Partition Bottom Hinge Assembly For 1" Door, 1-1/4" Pilaster Square Edge Cast Stainless Steel

Cast stainless steel construction. Set includes bottom hinge, pin and door insert. Also known as a Bathroom Toilet Stall Bottom Hinge Kit. Manufacture part #63033.

Shipped with mounting screws.

Toilet Partition Top Hinge Assembly For 1"Door,1-1/4"Pilaster Square Edge Cast Stainless Steel

Cast stainless steel construction. Set includes top hinge, pin and door insert. Also known as a Bathroom Toilet Stall Top Hinge Kit. Manufacture part #63043.

Shipped with mounting screws.

Corbin Russwin ED5200 Exit Device

Handing
Device is non-handed.
Lever trim is handed.
Bar Length
Easily field cut to size.
Standard: 36" (914mm) bar fits 30"- 36" door.
Stile
Minimum width 4-1/2" (114mm).

Replacement parts are also available

Toilet Partition One Ear Wall Bracket For 1-1/4" Panel, Stamped Stainless Steel

14 gauge (.075" thick) stamped stainless steel construction. Base is 1-1/2" x 2-13/32" with the mounting screws are 1-15/32" on center. Leg project out 2-1/2" with the thru hole at 2-1/8" from the base. Also known as a Bathroom Stall Wall Bracket and One Wing Bracket. Manufacturer part # 1849.

Shipped with screws

The Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase is also known as Part # P6000IR.

This Klauber Gear Motor Single Phase features:

• ¼ horsepower
• 115 volts
• RPM 12
• Amps 4

The powerful Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase is designed specifically for folding bleachers, providing reliable performance and durability. With its ¼ horsepower, it delivers the necessary strength to operate bleacher systems smoothly and efficiently. The Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase runs on a single-phase power supply of 115 volts, making it suitable for a variety of settings, including schools, gyms, and auditoriums.

As a facility manager, you are probably sure to check the bleacher hardware in your building periodically and replace any worn parts to maintain safety standards. Our online store has replacement parts readily available to order for this purpose. Regular maintenance is crucial for the longevity of your bleachers. We recommend scheduling routine inspections to identify any potential issues before they become major problems. This proactive approach not only enhances safety but also minimizes downtime, allowing your facility to operate smoothly. Whether it's for sporting events, school assemblies, or community gatherings, well-maintained bleachers contribute to a safe and enjoyable environment.

The installation process of this Klauber Gear Motor Single Phase is straightforward, allowing you to quickly set up and start using your bleachers without unnecessary delays. The Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase is built to withstand the rigors of frequent use, providing peace of mind for facility managers. Whether you are upgrading existing bleacher systems or installing new ones, the Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase is an excellent choice for ensuring safety and convenience in any venue.

For more information on the Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase or to purchase, please feel free to contact us. We always encourage you to ask us questions in order to get the best performance from your Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase.

VIRCO SLED BASED GLIDES Fits 1" outside diameter tubing. Glide has 3/4" base diameter. Stem diameter is 1/4" x 9/16" high.

all american

A=1-5/8"

103