Search results for: 'closer latch tape trim acrylic seat'

FEATURES

• Please note the factory will only sell in quantities of 10.
• Locks are individually keyed for single key access on a single lock
• Higher security 5-pin tumbler lock cylinder
• Rear mounted steel casing deters vandalism
• Locks have supervisory Control Key overide
• Each lock supplied with 2 keys
• Lock will work on both left and right hinged doors
• All Key Locks have a 5 year warranty from time of shipment
• 72 hour shipping available
  

APPLICATIONS

Fully retracting automatic spring latch for convenience

The Command Access MLRK-VD Motorized Latch Retraction is for use on the 33,35, 98 or 99 Von Duprin Exit Devices. This motor is 24 to 28 volts and has a Standard : 900 mA (Avg Current Peak); 215 mA (Avg Current Hold). This unit requires 18 ga wire.  And ships with (1) Motor Mount with MM5; (2) 40002 - 8/32 x 1/4 inch Phillips Head Screw; (1) 50030 8/Lead with vd Connector; (1) 50944 Molex Pigtail; (1) 40144 Dogging Hole Cap; (1) 50991 Fire Rated Drilling Template; (1) Replacement Dogging Tail Piece.

The MLRK1-VD is a cost-effective and straightforward way to upgrade your Von Duprin 33/35 & 98/99 series device to motor-driven latch retraction in the field. For AX devices, see the MLRK1-VDAX listed on the cutsheet below. UL Listed + 3 Year Warranty

The LCN 1370 was a door closer made in the late 1990's to 2006 or so. The closer had a special mounting plate that made installation very quick. Many people have this door closer in use and now they are starting to fail. The LCN 1370-18QF Quick Fix Plate converts the mounting holes of the 1370 to a standard template closer, which is 3/4" x 9-1/16". By using this plate you will not have to redrill holes in your door. The plate measures 2 by 10-1/4 inches with tapped holes that measure 3/4 x 9-1/16 inch. 

LCN Drop Plate for Pull Side Mounting

Use this LCN Drop Plate when mounting the door closer on the Pull or Hinge Side of the Door. Allows to door closer to me mounted on narrow stile doors.

LCN Part #'s
1260-18
1460-18
4040-18
4040XP-18
4010-18

Concealed Latch Keeper Bumper Inswing For 1-1/4" Square Edge Post Cast Stainless Steel

Cast stainless steel construction. Keeper is 1-1/4" tall by 2-3/8" wide by 2-9/16" deep. The strike is a17/32" thick and the slot is 7/16" deep. The opening to mount it on the square edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing 1-1/4". Manufacture part # 5983

Shipped with screws for mounting.

Toilet Partition Surface Mounted Black ADA Slide Latch Set W/ Indicator

Stamped stainless steel construction with a Black Finish. Slide lock measures 4-3/16" long by 1-1/8" tall by 15/32" thick. The mounting plate has mounting screws 1-1/4" on center and is 2-15/32" long. The lock projects out 1-3/16" from the face of the door. The indicator is 2" in diameter and 13/32" thick. The keeper is 3/4" wide by 1-7/16" tall by 1/16" thick. Commonly known as a Bathroom Stall Surface Mounted ADA Slide Lock and Toilet Partition Locks. Manufacturer part # 6065. For 1" thick doors.

Shipped with mounting screws.

Corbin Russwin 33L OEM Spindle 499F83-8

This Corbin Russwin Spindle is used on there Mortise Lock Lever Trim.

Corbin Russwin part # 499F83-8

Replacement Rod for the LCN 4630 Door Closer, LCN Part # 4630-82

The Stainless Stel Indicator Latch and Keeper are designed to work with for 1" doors and 1-1/4" pilasters thickness. Constructed of stainless steel with a brushed finish. Comes fasteners for installation. Known as manufacturers part numbers 905200,910128 and 910129.

The Emco R1 Wall Rack system is perfect for hotels, restaurants, churches and schools. It is easy to install and built to last.  They project 12-1/8" from the wall and the support brackets are 12" high and 1-7/16" wide.  The slats measure 3/4" by 1" rectangle with a wall thickness of .062" and are constructed of extruded aluminum and have plastic end closures.  The mounting brackets are made of cast aluminum that is powder coated black.  For the slats we have the option of Silver Anodized Aluminum or Bronze Acrylic Coated Aluminum.  We show the more popular sizes on the website, but we can get these up to 50' long.  Manufacturer will use slip joints so the rack can ship UPS/FEDEX.  Hangers are not included.

Von Duprin 8827-F/47-F Soffit Latch Kit

This component fits into the header and is used the Von Duprin 5547-F, 8827-F and 8847-F

Von Durpin Part # 114141
Old Part # 102930

Claridge Tackboards-Nucork Surface. 800 Series Type Co - 5/8" Face Trim. This item ships by truck. 

The Adams Rite 31-0619 is the Circuit Board that controls the Motorized Latch Retraction on the 8000 and 3000 Series Exit Devices. It is also known as the PCBA: SE Main (Black).

Picture coming soon!

Sargent Exit Device Lever Return Spring

This spring is used on Sargent Lever Trims for there Exit Devices.

2-1/8" LONG

Sargent part # 97-0425

Stainless Steel global slide latch with indicator and emergency access. Overall dimension 2-3/4" x 1-1/2" with 2-1/4" hole spacing. Used with new style doors 10/1/21 to current. Used with a 1 inch door. Security screws included. Manufactures part number 40-8263010.

The Aluminum Bleacher End Cap is also known as Part #P7002N.

Note: We offer 7½" (P7002na), 9½" (P7002nb), and 11½" (P7002nc) width for Aluminum Bleacher End Caps. They are 1¾" thick and feature 2 bends of 1⅛" & ⁹⁄₁₆". The Aluminum Bleacher End Cap includes self taping screws. Please select the appropriate size from the dropdown menu below.

This aesthetically-pleasing Aluminum Bleacher End Cap is designed to provide a clean and finished look to your aluminum bleacher system. Made from high-quality materials, these Aluminum Bleacher Ends ensure longevity and resistance to wear and tear, making them an ideal choice for schools, sports facilities, and outdoor events.

The Aluminum Bleacher End Cap is easy to install, fitting securely onto the ends of your bleacher rows. Its sleek design not only enhances the overall appearance of your seating but also helps to prevent debris from entering the bleacher structure, maintaining a tidy environment.
Whether you're upgrading existing bleachers or installing new ones, the P7002N End Cap is a reliable solution that combines functionality with aesthetic appeal.

Consider implementing a cleaning and maintenance schedule to keep your bleachers looking their best. A clean and well-maintained environment not only enhances the aesthetic appeal but also contributes to the longevity of the materials. Simple tasks like wiping down surfaces and removing debris from the Aluminum Bleacher End Caps can make a significant difference. Whether it's comfort, accessibility, or safety concerns, replacing worn-out Aluminum Bleacher End Caps with new ones can help you prepare for future upgrades or changes involving your bleacher systems. By prioritizing maintenance, safety, and user experience by installing new Aluminum Bleacher Ends, you can ensure that your bleacher system remains a dependable and welcoming space for all events.

Please feel free to contact us for assistance with ordering the correct replacement Aluminum Bleacher End Caps for your specific needs. We are always glad to help you choose the best options for your bleacher systems. Order yours today!

Concealed Partition Latch Keeper Bumper 1" Square Edge Cast Stainless Steel

Cast stainless steel construction. The strike and keeper measures 2-1/2" tall by 1-15/16" wide by 1-17/32 deep. The mounting holes are 1-1/2" on center. The stop measures 7/8" wide by 17/32" deep with a rubber insert bumper. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing 1". Manufacture part # 5733.

Shipped with mounting screws.

Current style Global chrome plated door catch includes screws for mounting. This is used with the 9g600 latch in ss. Product part number is 40-8212360. This part has a 3/8" gap for the catch and is 2-1/8" in length, 1-5/8" hole spacing and is 3/4" wide. 

Toilet Partition Keeper For Throw Latch Inswing Flat

Polished chrome plated Zamac construction. Keeper base is 2-1/2" high by 1-3/16" wide with a 1-1/2" hole spacing. Strike is 2-1/2" tall by 7/8" deep. The material 1/8" thick. The slot is 13/16" high by 1/4". Also known as a Bathroom Stall Keeper Inswing Flat. Manufacture part # 5180.

Shipped with mounting screws.

Low Rise Tip-n-Roll Preferred Aluminum Bleachers 3 and 4 rows high. Aluminum angle under structure 6" rise/row. First row seat 11-1/2" rise with 5" casters with non-marring wheels and non-marring foot pads. We offer for a 3 row high 7'6" wide for a 15 person maximum, 12' for 24 person maximum or a 15' for 30 person maximum. 4 row high bleachers are 7'6" wide for a 20 person maximum, 12' for a 32 person maximum and a 15' for a 40 person maximum seating. Preferred Tip-N-Roll Bleachers have 2 foot planks between rows.

Call for pricing********

ADA Partition Slide Latch with Occupied Symbol. Stainless steel door lock surface mounted for 1" doors, this can be used for doors less than 1" if the rod is cut down between the two pieces. All hardware included for installation. This manufactures part number is 50553. Hole spacing is 3-1/2".

Concealed Partition Latch Keeper Bumper 1-1/4" Square Edge Cast Stainless Steel

Cast stainless steel construction. The keeper and strike is 2-1/2" tall by 1-7/8" wide. The stop is 17/32" thick and projects out 3/4". The mounting holes are 1-1/2" on center. The locking slot is 7/16" deep. Generally used with concealed latches. Also known as a Bathroom Stall Strike and Keeper - Inswing/Outswing 1-1/4". Manufacture part # 5233.

Shipped with mounting screws.

Concealed Partition Latch Keeper Bumper Outswing 1-1/4" Round Edge Cast Stainless Steel

Cast stainless Steel Construction. The outside dimensions are 2-3/8" wide by 1-1/4" high by 1-3/4" deep. Stop projects out 1-1/8" by 1/2" thick with a rubber insert. Designed for an 1-1/4" thick post round edge. Also known as a Bathroom Stall Strike and Keeper Outswing 1-1/4". Manufacture part # 5573.

Shipped with mounting screws.

Current style Global stainless steel door catch includes screws for mounting. This is used with the 9g700 latch in ss. Product part number is 8262360. This part has a 3/8" gap for the catch and is 2-1/8" in length, 1-5/8" hole spacing and is 3/4" wide. 

Concealed Partition Latch Keeper Bumper For 1-1/2" Between Screws Cast Stainless Steel

Cast stainless steel construction. The strike and keeper measure 2-1/2" high by 1-13/16" deep by 1/8" thick. The stop has a 3/4" projection and is 9/16' deep with a rubber insert. The mounting holes are 1-1/2" on center. The slot is for the concealed latch is 7/8" high by 7/16" deep. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing Flat. Manufacture part # 5243

Shipped with mounting screws.

The Command Access MLRK1-FAL17 Motorized Latch Retraction Kit With REX is for use on the Falcon Dor-o-matic 1690/1790, AHT4/5, and First Choice 3600/3700 Series Exit Devices. The unit is 24 volt with Standard : 900 mA (Avg Current Peak); 200 mA (Avg Current Hold). The unit requires 18 ga wires. The package includes:  1) Motor Mount with MM5; (1) 50944 Molex Pigtail; (1) 50030 6 Feet Lead with VD Connector; (2) 40124 10-24 x 3/8inch Phillips Screws (Silver); (2) 40125 10-24 x 3/8inch Phillips Screws (Black).

The MLRK1-FAL17 is a cost-effective and straightforward way to upgrade your Falcon 1690/1790, First Choice 3600/3700, & AHT 4/5 series device to motor-driven latch retraction in the field. UL Listed + 3 Year Warranty

The Von Duprin 090076 Spring is located in top latch of the Surface Vertical Rod.  It is used on the 2227, 3327A, 3427A, 9827 and 9927 models. It is number 18 in the attached diagram. They are sold in packages of 10.

Permanent in ground Mount Aluminum Bench with out backrest with Galvanized Steel Legs. Available sizes are 6', 8' and 12' benches. All Hardware included, 2" x 10" anodized seat planks, 2-3/8" galvanized pipe leg design. Note 12' benches will ship by truck.

Call for Pricing********

Claridge Tackboards-Fabricork Surface. 800 SERIES TYPE CO – 5/8" FACE TRIM. SEE COLOR CHART.

Chrome Plated Partition Keeper Bumper For Throw Latch, For Inswing Flat Stop

Chrome plated Zamac die casting. The strike and keeper is 1-1/4" high by 2-1/2" deep by 1/8" thick. The stop is 1/2" deep by 1-1/4 wide with a rubber insert. The slots are 1/4" deep. Also known as a Bathroom Stall Strike and Keeper Inswing Flat. Manufacture part # 5650.

Shipped with mounting screws.

Concealed Latch Keeper Bumper Outswing Cast Stainless Steel

Cast Stainless Steel casting. The strike and keeper is 1-1/4" high by 1-3/4" deep by 1/8" thick. The stop is 1/2" deep by 1-1/4 wide with a rubber insert. Also known as a Bathroom Stall Strike and Keeper Outswing Flat. Manufacture part # 5643.

Shipped with mounting screws.

Norton 7700 Series Power Track

The Norton Power Track Closer-Holders combine the functions of a single point electromechanical door holder with the proven reliability of a 7700 Series Door Closer. The track assembly contains an arm slide and solenoid operated hold open mechanism and is available with or without an integral smoke detector. The closer is mounted on the door. The Power Track and hook-up box are mounted to the frame face for pull side installations or the frame soffit for push side installations.

Two versions, the Master Unit (PTDO) and the Support Unit (PTO). The PTDO has an integral smoke detector. The PTO can be plugged into the PTDO or into your existing fire alarm system. Both units can be mount pull side of the closed door, or the push side, please specify when ordering. Specify voltage (24 volt or 120 volt) and color (aluminum or dark brown). Dark Brown is a 3 week lead time, Aluminum is in stock.

The PTDO Master Unit is no longer available, they were discontinued in the 2024.

Chrome Plated Partition Keeper Bumper For Throw Latch Inswing Flat Stop

Chrome plated Zamac die casting. The strike and keeper measure 2-1/2" tall by 2-9/16" deep and is 1/8" thick. The stop projects out 3/4" and has a rubber insert. The mounting holes are 1-1/2" on center. Slots are 1/4" deep by 13/16" high. Also known as a Bathroom Stall Strike and Keeper - Inswing Flat. Flat backed for wall mounting. Manufacture part # 5280

Shipped with mounting screws.

Norton CloserPlus Non Hold Open Arm

This heavy duty Parallel Arm can be used with the Norton 1600, 9300, 8000 and 7500 door closers.

Aluminum is in stock, Dark Bronze is 2-3 week lead time.
Norton Part # 6770-5

Jackson Offset Arm Package. Includes arm, track and mounting screws

Jackson part # 20-1312-LC