Search results for: 'case latch thick tip acrylic space'

The Von Duprin 55 End Case is the housing on the hinge side of the door.   The function of this housing is to lift the cross bar, and support the function of the Active Case.  If your housing is on the right side when standing inside looking out, then you would order the Right Hand Case.  The package includes the housing, springs and back plate, the arm is not included.  The current part number on this part is 050196 and 050197, the old part number is 111931 and 111932.

The Von Duprin 99 Rim Center Case Cover replaces your old 1 or 3 piece cover.

The Von Duprin Cover comes with mounting screws.

Von Duprin part # 050071

Doromatic Complete 2090 and 1090 Active Case. Includes all of the interior hardware. Just unscrew or loosen the three set screws and remove your old case and install and tighten the three set screws. Housing measures 7-1/2" long by 1-3/16" wide.

4270902740 Left Hand Aluminum Stock
4270902742 Left Hand Dark Brown Stock
4270902743 Left Hand Black * One week lead time
4270902746 Right Hand Aluminum Stock
4270902748 Right Hand Dark Brown Stock
4270902749 Right Hand Black * One week lead time

Von Duprin 55 Center Case Axle

Von Duprin Part # 090050 or 090022

Window Strike 1/4" Thick Offset

1-3/8" hole spacing x 1/4" thick

white bronze construction with nickel plating

Window Strike 5/32" Thick Offset

1-3/8" hole spacing x 5/32" thick

white bronze construction with nickel plating

Window Strike 9/32" Thick Offset

1-3/8" hole spacing x 9/32" thick

white bronze construction with nickel plating

Window Strike 3/16" Thick Offset

1-3/8" hole spacing x 3/16" thick

white bronze construction with nickel plating

Window Strike 5/16" Thick Offset

1-3/8" hole spacing x 5/16" thick

white bronze construction with nickel plating

Von Duprin 9927 Center Case

This Von Duprin 9927center case replaces all earlier versions of the 9827 and 9927 Center Cases. Everything shown in the picture is included with the product. Along with all the mounting screws.

Von Duprin part # 050021

Von Duprin Exit Device 22 Center Case 109012

Von Duprin 22 Center Case. Replaces worn and broken Von Duprin 22 Center Cases

Von Duprin Part # 109012

Von Duprin 33/3547A/49A Center Case Cover Kit

Replacement Von Duprin 33/3547A/49A Concealed Vertical Rod Center Case Cover Kit.  Screws come with the new cover.

Von Duprin Part # 050485

Monarch 24-R Series Center Case Cover Kit

Replacement cover for the Monarch Falcon 24-R Narrow Stile Exit Device.   Kit includes cover and the mounting screws.

Falcon Part # 650247

Von Duprin Exit Device 22 Rim Center Case Cover

Replace your old or missing Von Duprin 22 Cover. This cover comes in aluminum or dark brown finishes.

Von Duprin part # 968603 SP28 or SP313

Monarch 25-V Center Case Kit

The Falcon / Monarch 25-V Center Case Kit 650242 for non Fire Rated Doors.  The Center Case on the Monarch Falcon 25-V is the same for the Fire Rated and the Non Fire Rated.

Falcon Part # 650242

Jackson 1085 Hinge Case, also the 1095 Jackson inactive Case. Includes everything in the housing.

The housing mounting studs are 6-5/16" on centers

Jackson part # 30-982 Right Hand Body and Arm Assembly
Jackson part # 30-983 Left Hand Body and Arm Assembly

Housing Shown in Aluminum

Plastic chair tip for 1" diameter round tubing chair legs.  Protect your floors against scratches and marks. These chair tips are available in tan, gray and black in a variety of sizes. Chair tips help prevent chair legs from coming through and damaging your floors. For Krueger Chairs, Tables and other furniture where the leg has a 1" outside diameter. 

PCT100T Tan
PCT100G Gray
PCT100B Black

Von Duprin 98/9947 98/9949 98/9975 Center Case Cover

Cover for the 050022, 050029 and 050030 Von Duprin Center Chassis Assemblies.

Von Duprin Part # 050073

Rubber Chair Tips For Legs With An Outside Diameter Of 1". Chair tip is for Hampden, Krueger and Samsonite Chairs. Available in Black or Gray.

Reinforced Rubber Crutch Tips For 5/8" Outside Diameter Round Chair Legs. The perfect solution when your metal chair leg punches through your rubber chair tip. Problem solved by placing the tube cap on the chair leg first, then the rubber chair tip to provide more of a surface area to displace the weight of the chair leg. Crutch tips help protect your floors from expensive damage. A variety of sizes available in both white and black color. 

Part # - Color
CRT62BTC - Black
CRT62WTC - White

Sargent 2828 / 2838 Center Case Cam

The Sargent 2828 / 2838 Center Case Cam is the Cam that the key cylinder actuates to open the door.   The Cam is located in the middle of the Center Case.  We can no longer get the retaining ring to hold it in place.

Sargent Part # 28-0109

Reinforced Rubber Chair Tips For 1" Outside Diameter Round Legs

One of the biggest problems with rubber chair tips is the metal leg punching through the rubber feet. This happens because the metal chair legs are sharp and blunt. By installing a chair tube cap first, the rubber chair leg has more of a surface area to displace the weight.

Part # - Color
RCT100BTC - Black
RCT100GTC - Gray

Clear Plastic Door Kick Plate

.125 inch thickness

Clear Acrylic

Custom sizes width x height x .22 = Cost $

Brackets designed to mount plexiglass/acrylic sheets to desk surface edge when creating separation/barrier. Brackets are adjustable for thickness from 1/8" to 3/8". It is recommended for use of 1/4" Thick material. Sold as a Pair. Made of Aluminum Alloy. Screws and inserts included. Uses a 5mm/3/16" Allen Key(Not Included) to install screws These are available in either Silver or Black Finish. Silver Finish are readily available while Black Finish may have an extended leadtime depending on quantities being ordered.

Measurements

Height: 2-1/2"

Width: 1-3/4"

Depth: 5/8"

Weight:About .9lb

Top to Bottom: 3-5/8"

Plate Width: 1-3/4"

Plate Length: 3"

Plate Height: 3/16"

Gap/Spacing: 1"

Brackets designed to mount plexiglass/acrylic sheets to desk surface edge when creating separation/barrier. Brackets are adjustable for thickness from 1/8" to 3/8". It is recommended for use of 1/4" Thick material. Sold as a Pair. Made of Aluminum Alloy. Screws and inserts included. Uses a 5mm/3/16" Allen Key(Not Included) to install screws These are available in either Silver or Black Finish. Silver Finish are readily available while Black Finish may have an extended leadtime depending on quantities being ordered.

Measurements

Height: 2-1/2"

Width: 1-3/4"

Depth: 5/8"

Weight:About 1.3lb

Top to Bottom: 3-5/8"

Plate Width: 1-3/4"

Plate Length: 5-3/4"

Plate Height: 3/16"

Gap/Spacing: 1"

Window Strike 11/64" Thick Inline

1-3/8" hole spacing x 11/64" thick
White bronze construction with nickel plating.

Von Duprin 55 Hinge Case Spring

Von Duprin 55 hinge case spring, spring lifts arm.

1-5/8" long x 5/8" diameter

Von Duprin part # 090052

Rubber Crutch Tips For 3/4" Round Chair Legs. This rubber chair tip fits a chair leg with a 3/4" outside diameter. Protect your floors from damage by using Rubber Chair Crutch Tips. Available in black or tan. Other sizes available. Easy to install, simply slide over your chair leg tubing. Great to use on chair legs, stools, tables and other applications where a heavy duty chair tip is needed. 

CRT75B BLACK

CRT75 TAN

Reinforced Rubber Chair Tips For 3/4"Outside Diameter Round Legs

One of the biggest problems with rubber chair tips is the metal leg punching through the rubber feet. This happens because the metal chair legs are sharp and blunt. By installing a chair tube cap first, the rubber chair leg has more of a surface area to displace the weight.

Part # - Color
RCT75BTC - Black
RCT75GTC - Gray

Von Duprin 98/99 Rim Center Case

Replaces all previous versions of the Von Duprin 98/99 Rim Device Center Cases. All internal parts, springs, screws and cover mounting bracket included.

Von Duprin Part # 050020

This replacement tip is used on the WB11, WB12, WS20 and WS33.
5/8" insert diameter
7/8" head diameter
1" overall length

Reinforced Rubber Crutch Tips For 7/8" Outside Diameter Round Chair Legs. Help protect your floors from damage. This application is for when your metal chair leg punches through your Rubber Chair tip. Using the Tube Cap on the chair leg first, then apply the Rubber Crutch Tip over the leg will solve that problem by providing more of a surface area to displace the weight. Available in black or white and a variety of sizes.

 Part # - Color

CRT87BTC - Black
CRT87WTC - Tan

Reinforced Rubber Crutch Tips For 1" Outside Diameter Round Legs. One of the biggest problems with rubber crutch chair tips is the metal leg punching through the rubber feet. This happens because the metal chair legs are sharp and blunt. By installing a chair tube cap first, the rubber chair leg has more of a surface area to displace the weight.

Part # - Color
CRT100BTC - Black
CRT100WTC - White

Medart Locker Handle Case, Uses one screw.

Zamac die cast construction, polished chrome finish. Latch base is 4" high with 2-3/4" hole spacing. Latch bolt is 3-3/16" long by 3/4" wide by 3/16" thick. The latch bolt clearance is 9/16" from the back of the base to the under side of the latch bolt and projects out 15/16". The latch projects out 1-9/16" from the face of the door when installed. Also known as a Bathroom Stall Surface Mounted Slide Bolt Latch. Manufacture part # 5020.

Shipped with mounting screws.