Search results for: 'bleacher robert board 60 1 hussey gearbox reduc'

Threaded stem metal base glide, thread is 1/4-20, base diameter 1 1/6", and stem length is 1/2". Glide is furnished with nut.  This non swivel leveler stops wobbling on uneven floors. 

Toilet Partition Top And Bottom Hinge Kit For 1" Thick Door To 1" Square Post

also known as a Bathroom Stall Door Hinge Kit. Includes everything shown in the picture.

Manufacture part # 63150

Toilet Partition Top Hinge Assembly For 7/8" Door To 1-1/4" Post Square Edge Cast Stainless Steel

Cast stainless steel hinge. Hinge mounts to 1-1/4" square edge post or pilaster, for use with 7/8" thick doors. Kit includes top hinges, pintle, pin and inserts. Also known as a Bathroom Stall Top Pivot Hinge Set. Manufacture part # 63023

Includes all screws.

Steel Flag Bracket - 1/2". Zinc plated steel construction. The flag bracket projects out at a 45 degree angle. For use with 1/2" diameter staffs.

Reinforced Rubber Crutch Tips For 1" Outside Diameter Round Legs. One of the biggest problems with rubber crutch chair tips is the metal leg punching through the rubber feet. This happens because the metal chair legs are sharp and blunt. By installing a chair tube cap first, the rubber chair leg has more of a surface area to displace the weight.

Part # - Color
CRT100BTC - Black
CRT100WTC - White

Claridge Map Hook 1" map rail. Plastic Construction. 

Nova 1 hand dryer’s are an economical way to upgrade any restroom. Nova 1 offer two options: Hardwired or Plug-In. The Nova 1 hardwired is universal between 110-240v. The compact design make it ADA Compliant with the unit measuring 9”x9.7”x4” and being surface mounted. Providing an economic way to add an ADA hand dryer to a consumers restroom. Known as World Dryers part number WHD-830.

• Economic/Entry Level Dryer
• Automatic Operation Infrared Sensor
• Surface Mounted
• Low Sound Level
• Compact Design
• Durable Die Cast Aluminum with White Epoxy Enamel Finish
• Universal Voltage: Uses smart technology to adapt to almost any facilities voltage. Voltage extends from 110-240v(Min.15 Amp Recommended).
• 2 yr Limited Warranty

Claridge End Stop 1" for map rail. Plastic Construction. 

Alcove One Ear Bracket Panel Kit for 1/4" Offset. This kit is used for panel to pilaster 1/4" offset and for 1" panel to wall bracket chrome plated. Security screws included. Also known as 615360.

Marsh 1" End Plate Pair for 1" map rail. Constructed of Aluminum. 

The 1" Q-Ball Floor Protector is for use on 1" outside diameter chair and table legs. The adapter shown on the right fits over your existing glide, and then the Q-Ball slides over the adapter. Constructed of Gray Plastic.

Comtec Toilet Partition Aluminum 6" Inswing Strike And Keeper For 1" Post Or Pilaster

Clear Anodized aluminum construction. Strike and Keeper is 6" high by 1-15/16" wide. The three mounting screws are 2" on center apart. The slot is 3/8" deep by 1-1/2" high. Also known as a Bathroom Stall Strike and Keeper Inswing 1". Used mostly on Solid Plastic (HDPE) Toilet Parttions. Some manufacture part #'s are 5778, HSISA, and 650-2873.

Shipped with mounting screws.

Post Cap for 1-3/4" post. This is made as a top cap and has a chrome finish. The manufacturer part number is 6500.

International 8630S Surface Vertical Rod Device-Grade 1

DC 8000 Series Exit Devices are heavy duty and designed for heavy traffic applications. The devices are Underwriters Laboratory (UL, USA and ULC, Canada) listed for Panic Exit Hardware or Fire Exit Hardware, and are certified to ANSI A156.3-2001 Grade 1.

Non handed, 4-1/2" minimum stile width. Smooth Surface.

For doors 29" to 36" wide order the Size 30 to 36"
For doors 36" to 48" wide order the Size 48"

1" Tube Cap

Round Tubing - 6 prong Tube Caps are pushed in easily and hold securely in 16 or 18 gauge round tubing. Sold individually.

Fits 1" outside diamter legs, 1" base diamter

Nickel Base Finish

projects 1-3/4", 1-3/8"ht

3/4" center to center hole spacing

Slotted Head Bolt 10-24 X 1/2"

Hand Dryer designed for Behavioral Health appliactions with Anti-Ligature features, angles top, welded corners, single tube exhaust prevent looping, tying off and prying. 18 Gauge Tamper-Resistant Stainless Steel cover and flush pin-hex security screws. Designed for Behavioral Health and Detention Centers. 

Voltage Options

MH-1 (115-120V)

MH-2 (208-240V)

Chrome plated outswing door kit for square edge doors and posts. For 1" doors and 1" post. All hardware screws included for installation of these products. All hardware is a gravity close so your door self closing every time. Also known as part number 21300.

Toilet Partition Keeper For Inswing Doors 1-7/8" Between Screws Stainless Steel

14 gauge (.075" thick) stainless steel construction. Keeper is 2-7/8" high x 1-13/16" wide with 1-7/8" hole spacing. Lip is 9/16" and the slot or cut out is 7/32" x 1". Also known as Bathroom Stall Keeper Inswing. Manufacture part # 6319.

Shipped with screws.

Restroom Door Kit Outswing 7/8" Door & 1-1/4" Post Cast stainless steel. All hardware screws included for installation of these products. All hardware is a gravity close so your door self closing every time. Also known as part number 27813.

Nylon Glide Caps-1-7/32". Fits over table and chair glides that have an outside diameter of 1-7/32".  Made of a natural white nylon, that will not color or scratch floors.

Partition Keeper Bumper Inswing 1" Square Edge Cast Stainless Steel

Cast stainless steel construction. The strike and keeper is 2-1/2" tall by 1-15/16" wide. The mounting holes are 1-1/2" on center. The stop is 2-1/2" tall by 13/16" projection with a rubber insert. The two slots are 5/16" deep by 13/16" high. Also known as Bathroom Stall Strike and Keeper Inswing 1". Manufacture part # 5823.

Shipped with mounting screws.

Non-Swivel Leveler Threaded Stem Glide with metal base. Thread is 1/4-20, Base Diameter is 1 1/16" and the stem length is 1". This glide screws into a 1/4" threaded leg hole to put a selected height. Use this product to stop wobbling on an uneven floor. 

Partition screen urinal bracket kit for 1" thick panel, two ear bracket that is chrome plated. All bracket kits include security screws to mount the brackets. Also known as 15510. 

1/4-20 Threaded Leveler with a Felt Base to be screwed into a 1/4" threaded hole in furniture leg. You can also combine with a t-nut to use in wooden furniture. Base Diameter and Stem Length are 1" on this glide. 

Partition Keeper Bumper Inswing 1" Post Square Edge Cast Stainless Steel

Cast stainless steel construction. Strike and Keeper measures 2-1/2" high by 1-15/16" wide. Stop is 17/32" thick and projects out 13/16". The screw holes are 1-1/2" on center. The slot is 5/16" deep by 1-1/2" high. This Bathroom Toilet Door Keeper is designed for use on 1" thick square edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing 1". Manufacture part # 5623.

Shipped with mounting screws.

If your toilet partition (bathroom stall) wall bracket is stamped 1620, then chances are you have the Two Ear Wall Bracket for 3/4″ thick toilet partition panels. This brackets base is 1-3/8″ wide x 3″ long with 2-7/32″ center to center hole spacing. The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. The bracket is made of a die cast material that is then chrome plated. The bracket sometimes goes by the name Bathroom Stall (toilet partition) Two Ear Bracket or Wall Bracket

U Bracket Stainless Steel for 1/2" Panel. This is used with a 1/2" thick panel only. The hole spacing is 1-1/2" and height is 3", and sticks out from the wall 2-1/2". The overall width is 5/8". This is also known as 2189. The stainless steel is flat and rolled to form a two ear partition bracket.

Adjustable Height Swivel Glide, Nickel Based for chair legs with a 5/8" outer diameter and a 1/2" inside diameter. The base of this glide is 1 1/4" in diameter. This glide helps level uneven chairs. 

Drawer Pull 3-1/2" Centers Stainless Steel, stainless steel wire pull. Measurements are 3-3/4" wide x 1-1/4" projection and the 8-32 screws are included.

Sled Base Felt Stem Glide with a 1/4" insert diameter. The base diameter is 7/8" and the Stem Length is 1/2". This glide works on any diameter sled base chair. This glide gently taps into 1/4" hole on the bottom side of a sled leg. Felt bottom to help protect floors.