Search results for: 'curtain horn horn roll strike 1 inc'

Cast Stainless Steel

Used on many Toilet Partition Manufacturers Plasitc Laminate stalls

40-8562304

The Handicap Grab Bar is fabricated of #18 gauge stainless steel with a #4 satin finish.  They are available in 1 1/4” and 1-1/2” outside diameter.  All bars maintain a constant 1 1/2” offset, which is the distance between the inside of the bar and the mounting surface.  The mounting flanges have a 3” diameter.  We offer two types of mounting,  exposed screw mounting and snap on flange concealed. When properly installed they will easily support up to 250 pounds.  The recommended height for mounting these grab bars is 33 to 36” above the finished floor, but heights vary depending on local codes.  The overall length of a 12" grab bar is 15" due to the 3" diameter flanges.  Due to the various materials that these are mounted on, screws are not included.

Cast stainless steel outswing door kit for square edge doors and posts. For 1" doors and 1" post. All hardware screws included for installation of these products. All hardware is a gravity close so your door self closing every time. Also known as part number 21343.

Toilet Partition Continuous One Ear Wall Bracket For 1" Panel Aluminum

Constructed of extruded anodized aluminum. Base is 2-5/8" wide by 54" long, with screw holes every 13" or so. The legs project out 2-3/4" with the thru hole at 2-3/8" from the back of the base. The legs have a clearance of 1" for 1" thick panels. Sometimes known as Bathroom Stall Continuous One Ear Wall Bracket. The manufacturers part numbers are 2878, and 650-9750-54. These brackets are shipped with all the needed fasteners.

C-Fold, Multi-Fold Paper Towel Dispenser
22 gauge Type 304 Stainless Steel
Heavy duty door and piano hinge
Tumble lock on doors and waste receptacle
600 C-fold or 800 Multi-fold towel capacity
13"w x 26"h x 4"d

C-Fold, Multi-Fold Paper Towel Dispenser
22 gauge Type 304 Stainless Steel
Heavy duty door and piano hinge
Tumble lock on doors and waste receptacle
600 C-fold or 800 Multi-fold towel capacity
13"w x 26"h x 4"d

The Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase is also known as Part # P6000IR.

This Klauber Gear Motor Single Phase features:

• ¼ horsepower
• 115 volts
• RPM 12
• Amps 4

The powerful Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase is designed specifically for folding bleachers, providing reliable performance and durability. With its ¼ horsepower, it delivers the necessary strength to operate bleacher systems smoothly and efficiently. The Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase runs on a single-phase power supply of 115 volts, making it suitable for a variety of settings, including schools, gyms, and auditoriums.

As a facility manager, you are probably sure to check the bleacher hardware in your building periodically and replace any worn parts to maintain safety standards. Our online store has replacement parts readily available to order for this purpose. Regular maintenance is crucial for the longevity of your bleachers. We recommend scheduling routine inspections to identify any potential issues before they become major problems. This proactive approach not only enhances safety but also minimizes downtime, allowing your facility to operate smoothly. Whether it's for sporting events, school assemblies, or community gatherings, well-maintained bleachers contribute to a safe and enjoyable environment.

The installation process of this Klauber Gear Motor Single Phase is straightforward, allowing you to quickly set up and start using your bleachers without unnecessary delays. The Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase is built to withstand the rigors of frequent use, providing peace of mind for facility managers. Whether you are upgrading existing bleacher systems or installing new ones, the Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase is an excellent choice for ensuring safety and convenience in any venue.

For more information on the Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase or to purchase, please feel free to contact us. We always encourage you to ask us questions in order to get the best performance from your Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase.

Jackson 1085 Concealed Vertical Rod Exit Device

Jackson 1085 Series Exit Device is universally recognized as the standard for aluminum storefront hardware. Made of high tensile strength aluminum.
Non Handed
Comes with 45" cross bar that is easily cut in the field, includes all screws, strikes and concealed vertical rods.

Replacement parts are available, in stock!

Project In Handless Window Lock 1-3/8"

Cast white bronze with a brushed nickel finish

Wayne Bleacher Wheel, 1/4"x13/16"x3". Soft rubber wheel 100# load capacity. Known as 262wn.

Indoor Flag Stand - 1 3/8". These cast stands are designed to compliment any flag set. Easily movable, these are the most practical stands for general use. This flag pole base is 12" diameter and 6" high. This flag stand weighs 15 pounds. 

Indoor Flag Stand - 1". These cast stands are designed to compliment any flag set. Easily movable, these are the most practical stands for general use. This flag base weighs 15 pounds. The flag stand is 12" diameter and 6" high. 

Universal Bleacher Spring 2-1/2" long.

Interkal Bleacher Gearmotor 1/2 hp, 3 phase, 460 volts, 12 RPM and known as 652566 or k01151g600. 1 week delivery.

Knickerbocker Hinge Pin For Metal 1/4" Diameter 2-3/4" Long, Known as part number 216.

Metal based Swivel Glide for round tubing. Measurements of the chair leg are  5/8" O.D. X 1/2" I.D. This glide comes with Ferrule. Used by Peabody and other manufacturers. Base of the glide is 1 1/4" metal.  Swivel glide, grips inside of leg, see "More View" for picture of clip.  Metal base glides are very popular in schools and institutions and move easily across smooth or carpeted floors.  Metal base glides are nickel plated and are extremely durable, but when they do wear out, they will scratch the floor.  The glide freely swivels beyond 30 degree angle. Glide grips leg with outside holding clip, meaning it grabs the outside of the leg, see more views for picture of outside holding clip. 

Toilet Partition Continuous Hinge Without Spring, 57-1/2 Long Stainless Steel

16 gauge (.060" thick) stainless steel construction. 3" wide when laid flat x 57-1/2" long with holes every 11" or so. 1/8" diameter hinge pin. Hinge can be raised up 3/8" for emergency entry. Also known as a Bathroom Stall Piano Hinge, or Full Length Stainless Steel Continuous Piano Hinge. Manufacture part # 7649.

Shipped with all the fastners

Glynn-Johnson 410 Series Overhead Door Holder/Stop Concealed Mounting

The perfect combination of form and function, Glynn-Johnson 410 series holders and stops offer effective door control and a low-profile design. Each model is constructed so that the channel is encased in the door and the jamb bracket is mortised in the frame. When the door is open, the arm and jamb bracket are visible. Conversely, when the door is in the closed position, the entire holder is completely concealed.

The 410 fits in a mortised channel on top of the door, if your doors are not mortised on the top of the door, you would have to mortise them out.  Replaces the older version GJ310, GJ320 and GJ330 series.

GJ410 Catalogue

Ordering Online All Powder Coated Metal Floor Anchored Urinal Screen Manufactured by Global Partitions, see color chart below. For other factory colors please call for pricing. All toilet partitions ship in 48-72 hours plus 2-4 days travel. All standard chrome plated brackets included. Floor Anchored Urinal Screen 70" high pilaster and 58" high panel. Width of screen 16"-76"x 58"ht
Color Chart

Fenestra Casement Operator

The arm is 9" long and the outside screw spacing is 5-1/4". The inside threaded holes are 4-1/4" apart. Die cast construction with steel arm. Ships with handle and mounting screws.

Endura Floor Stands for U.S. Flag. Our most popular floor stand. Comes complete with weighted inner core and brilliant anodized finish.12" diameter, 6" high and weighs 14 lbs.

Glynn-Johnson 450 Series Overhead Door Holder Surface Mounted

Glynn-Johnson 450 series holders and stops provide reliable and versatile surface-mounted overhead door control for all medium to light-duty applications. The visible components are available in a wide variety of architectural finishes to complement any design. The Glynn-Johnson 450 series holders and stops are designed for installation in virtually all types of doors and frames including doors with conventional butt hinges, offset pivots, continuous hinges, swing clear hinges and many other specialty hinges. The templates provided allow for variable mounting positions, ranging from 85° - 110° of opening.

The 450 Series replaces the older GJ360, GJ370 and GJ380 Series.

GJ450 Catalogue

Lyon Metal Locker Single Tier Lock Bar for 60" locker, length 53-1/4". Used September 2004 - Current.
Comes with 3 nano rollers. Also known as RH679460.

Coat Hook 3" Projection x 1-3/4" High Cast Stainless Steel

Cast stainless steel construction. The hook base measures 1-3/16" wide by 1-9/16" high. The long hook projects out 3" and the short hook projects out 1-1/2". Also known as Bathroom Stall Hook. Manufacture part # 4023.

Compact high-speed hand dryer for applications where less space is available. 5-year warranty. 9-25/32" W x 6-5/8" H x 5-7/16" D
FEATURES

• Quick drying — less than 15 seconds
• Operates automatically using infrared sensor
• Auto-resetting thermostat
• 60-second automatic shut off
• Cover fabricated of heavy-duty, one-piece-formed stainless steel

Felt Pads 1" Diameter, self adhesive for easy installation in seconds. Prevents scratching on floors and reduces noise made by chairs. 3/16" thick, NO LONGER AVAILABLE IN GRAY, THEY ARE NOW A TAN COLOR. 

Glynn-Johnson 90 Series Overhead Door Holder Surface Mounted

Glynn-Johnson 90 series holders and stops are the most rugged models available for heavy-duty applications. The channel is surface-mounted to the door, most often with barrel nuts, and the jamb bracket is surface mounted to the jamb, requiring minimal door and frame preparation.

GJ90 Catalogue

Toilet Partition Stainless Steel Continuous U Bracket, 71", 7/8"x1-1/2" 18 Gauge.

Stainless Steel Construction 18 gauge. U bracket is for 7/8" wide partitions and is 1-1/2" height and 71" long. Holes are typically spaced every 13-1/2" vertically. This bracket is also known as a Full Length Toilet Partition Continuous U Bracket 71". Bracket has rounded edge radius. Designed to attach pilasters and/or panels to walls. Continuous brackets help eliminate sightline into stalls.

*Fasteners not Included *

Manufacture part # 204099

Square Security Clothes Hook designed to snap down if excessive load is placed on hook. Fabricated from type 304 stainless steel, 12 gauge and backplate 14 gauge with satin finish. Product is offered in 2 mounting types: Front or Chase(Rear). Front mount has 4 dimbled holes through flange bracket and comes with torx mounting screws.Chase mount will come with rods welded to back and nuts for mounting. There are 3 options for the chase mount which you will have to select and each will come with specific sized rods to affix hook through wall. Options are to accommodate the wall thickness they will be mounted though. Designed in mind for Behavioral Health and Detention Centers.

Chase Options

• Less than 6" Wall
• Between 6"-8" Wall
• More than 8" Wall, Custom size

Dimensions

4-1/4″ x 4-1/4″ x 2-1/4″ (108 x 108 x 57 mm)

*** CHASE MOUNT DISCOUNTINUED 2024-25 ***

Partition Anti-Grip Headrail 1" X 65" Type B Aluminum

Extruded anodized aluminum construction. The cross section measures 2-3/4" high by 1-3/32" by 65" long. The part that fits on top of the pilaster is 1" wide by 3/4" deep. The wall thickness on this part is 3/64". Also known as a Bathroom Stall Headrail. Manufacture part # 80042.

This product is usually used on Solid Plastic (HDPE) Toilet Partitions.

Also know as Part# 9THP75

Partition panel bracket kit for 1" panel, Two eared cast stainless steel plated bracket. Part includes all security fasteners to install the brackets. Also known as 615033.