Search results for: 'goods 8 detex bronz door hold'

Von Duprin 88 Night Latch Trim

Plate measures 3" wide by 14-3/16" long, with an 1-5/8" bore for cylinder.

Von Duprin part # 880NL-R

#14 x 5/8" Screw 6 Lobe(T-27), Chrome, 7/16" diameter head, also known as 92193. This uses a Torx bit to drive screw.

Ives 7212 Pivot Set

• Handed
• Top, header mount
• Bottom, jamb mount
• Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
• Maximum door load 200 pounds
• Vertical adjustment range 3/16", with positive locking

Handing diagram

The International Flushbolt Standard Guide is the piece that fits into the top or bottom of the door and acts as a guide for the Flushbolt Rod.  The piece measures 1-3/8" x 1-1/2".  The square hole in the piece is a 1/2" square.  The manufacture part number is FG-1200.

Hussey Bleacher Wheel 5" x 1-3/16" x 3/8". Also known as 2011007. Load approx. 190 - 210 lbs.

Lyon metal Locker Door Jamb, Used September 2004 - Current. Also known as 6727.

Dor-o-Matic 1690 Pinion Support Bracket. Bracket holds pinion tip so that it will not slip

Doromatic part # BRKT.478, BRKT.133 or PB312

Dor-o-Matic 1690 Repair Parts Breakdown

Accurate Stainless ADA Door Kit Old Style, Used January 1-2013 to September 2021. This door kit includes all you see and the security screws. Also known as 50-8261515. Stainless steel material.

The Cal Royal Escutcheon 4400 Lever Trim is non handed (easily field reversible), thru-bolted, rigid non clutch lever for the 4400 Rim Device. The key locks or unlocks the lever. The Escutcheon measures 2-3/4 by 8-1/2 inches, the lever length is 4-3/4 inches.

Plastic Chair Tips Square Tubing for 7/8" Outside Diameter X 13/16" Inside Diameter. Fits square tubing legs with an outside diameter of 7/8" and an inside diameter of 13/16". Available in black. 

#10 x 5/8" Long Screw 6 Lobe(T-27) Chrome, 7/16" diameter head, Also known as 90963. This uses a Torx bit to drive the screw.

Replacement Dorma 9000 Series End Cap, sometimes know as the EC9

Shown in Dark Bronze

LCN Sentronic Door Closer 4040SE-168 Track Slider

The slider is not longer sold separately, it is sold with the roller.  You have to take the Assembly apart to get just the slider.

One-Way Shoulder Screw & Barrel 7/8" -1 1/16" Grip, Chrome Plated. Use a Flat Head Screw Driver to install. This is a 10-24 thread.

Partition Two Ear Wall Bracket For 7/8" Panel Cast Stainless Steel

Cast stainless steel construction. Base is 1-1/2" x 3-1/2" with 2-3/4" hole spacing. Bracket walls are 1/8" thick. The legs project out 2-1/2" with the thru holes at 2-1/8" from the bottom of the base. Also known as a Bathroom Stall Two Ear Wall Bracket, or Two Ear 7/8". Manufacture part # 1633

Shipped with mounting screws.

Reinforced Rubber Crutch Tips For 5/8" Outside Diameter Round Chair Legs. The perfect solution when your metal chair leg punches through your rubber chair tip. Problem solved by placing the tube cap on the chair leg first, then the rubber chair tip to provide more of a surface area to displace the weight of the chair leg. Crutch tips help protect your floors from expensive damage. A variety of sizes available in both white and black color. 

Part # - Color
CRT62BTC - Black
CRT62WTC - White

Reinforced Rubber Crutch Tips For 7/8" Outside Diameter Round Chair Legs. Help protect your floors from damage. This application is for when your metal chair leg punches through your Rubber Chair tip. Using the Tube Cap on the chair leg first, then apply the Rubber Crutch Tip over the leg will solve that problem by providing more of a surface area to displace the weight. Available in black or white and a variety of sizes.

 Part # - Color

CRT87BTC - Black
CRT87WTC - Tan

Black Round Plastic Chair Tips for  Round Tubing chair legs with a  5/8" Outside Diameter X 1/2" Inside Diameter.

83 Series Tube Balances - 3/8" Diameter

See Attached pdf, for more information.

Threaded spring clip for round legs. 1/4-20 thread for use with our LA10625 and SLA12525. 1" outside and 7/8" inside diameter. This spring clip has a 1/4-20 thread. 

Toilet Partition One Ear Wall Bracket For 7/8" Panel Cast Stainless Steel

Cast stainless steel construction. Base of the bracket is 2" x 1-1/2", with 1-1/8" hole spacing. Bracket legs project out 2-1/2" with the screws at 2-1/8" on center from the base. The four holes are 1/4" diameter. Also known as a Bathroom Stall One Ear Wall Bracket or One Ear 7/8". Manufacture part # 1653.

Shipped with mounting screws.

Plastic Chair Tips for Square Tubing Chair Legs. This tip is For a 1-1/4" Outside Diameter X 1-1/8" Inside Diameter  Chair Leg. Available in Black. 

Von Duprin 98 rim exit devices for all types of single and double doors with mullion, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1. The Von Duprin 98 device has a smooth mechanism case and the Von Duprin 99 device has a grooved case. The rim device is non-handed.

Ships with all the mounting screws and the 299 Strike.

Toilet Partition U Bracket For 1" Thick Panel Cast Stainless Steel

Cast stainless steel construction. Bracket base is 1-3/8" x 1-1/4" with two mounting screw holes. Bracket legs project out 1-3/8" with the thru hole at 1" on center from the bottom of the base. Also known as a Bathroom Partition Stall U-Bracket or Wall Bracket 1". Manufacture part number 1913

Shipped with mounting screws

Corbin Russwin ED5200A Active Head

Used on the Corbin Russwin ED5000 Rim Devices, for fire rated doors. For non fire rated doors, order the G650F35-8. A fire rated door is a door were you can NOT use your allen wrench to dog, or lock, the door in the open position during business hours.

Corbin Russwin part # 650F36-8

Rim Cylinder Hub Position for the ED5200A

Von Duprin Electric Strike 6112 24VDC

Von Duprin 6100 Series electric strikes are designed for use with Rim devices.  The 6112 has a 3/4” latch bolt throw, 9” face plate length, 1-5/8” width, and an 1-3/4” backbone depth.  The lock retrofits the Folger Adams FA 310-4.  Other voltages and replacement parts are available. 

FSE - Fail-secure.  Requires power to be applied to unlock the strike lip.  On loss of power, the strike lip is locked-Fire Rated

FS - Fail-safe.  Requires power to be applied to lock the strike lip.  On loss of power, the strike lip is unlocked.  Non Fire-Rated.

Door Stop / Holder Rubber Shoe

Replacement rubber shoe
1/2" insert diameter
1" base diameter
1" height

Universal Bleacher Wheel, 1/2" x 1-1/8" x 3 1/2", Uses axle pin P2073U.

Toilet Partition Stainless Steel Continuous One Ear Bracket, 71", 7/8"x2-1/2" 18 Gauge.

Stainless Steel Construction 18 gauge. One ear bracket is for 7/8" wide partitions and is 2-1/2" height by 2-9/32" wide by 71" long. Holes are typically spaced every 13-1/2" vertically. This bracket is also known as a Full Length Toilet Partition Continuous One Ear Bracket 71". Bracket has rounded edge radius. Designed to attach pilasters and/or panels to walls. Continuous brackets help eliminate sightline into stalls.

*Fasteners not Included *

Manufacture part # 204039

Jackson Door Closer Center Hung Arm

Jackson Part # 20-400B

Jackson Door Closer Center Hung Arm

Jackson Part # 20-2085

Used on chairs and table, so you can use an adjustable height gilde. Used with the LA10625 or SLA12525. 1/4-20 Thread, 1-1/8" outside diameter and 1" inside diameter.

If your toilet partition or bathroom stall wall bracket is cast with the number 1920 on the back, then you have the “U” Wall Bracket for 1″ thick toilet partition panels. The wall bracket is usually mounted on the wall or the pilaster to mount the toilet partition stall panels. This bracket is 1-1/4″ wide x 1-3/8″ tall, with the through hole located at 2-1/8″ from the back. If features 2 holes with a 1/4″ diameter, with two of them on the base. The bracket is made of a die cast material that is then polished chrome plated. This bracket is sometimes called a Toilet Partition or Bathroom Stall X Long “U” Bracket, or X Long “U” Wall Bracket.

Ives Roller Latch RL32

The Ives Roller Latch RL32 is constructed of Brass and Plated to your desired finish.  The body measures 1-1/8" wide by 2-1/4" high and 2-1/4" deep.  The roller is constructed of Nylon, and has an adjustable projection up to 1/2".  Fits a standard heavy-duty cylindrical lock cutout.