Search results for: 'gloss 8 drill been door hidden'

Toilet Partition Continuous Toilet Partition Hinge 57-1/2" With Spring Close Stainless Steel
Lh Inswing or Rh Outswing See Diagram

16 gauge (.060" thick) stainless steel with 4 springs. 3" wide when laid flat x 57-1/2" long. 1/8" diameter hinge pin. Mounting screws are located every 11" or so. Can be raise up 3/8" for emergency entrance. Also known as a Bathroom Stall Piano Hinge, or Full Length Stainless Steel Continuous Piano Hinge. Manufacture part # 7669.

Shipped with all the fasteners

Truth 24.31 Sash Lock

Truth 24.31 casement window sash lock.  The hole spacing is 3-13/16" and the "Fork" projects out  1-7/8".   Housing is made of die cast metal that is then powder coated.

Truth Part # 24.31.xx.004

Lathern or Liquid Dispenser
8" w x 5" h x 3 d"
40 oz Bulk Fill
Stainless Steel

Casement Window Handle Keeper Double Side

2-5/16" hole spacing x 5/8" wide

Stamped aluminum construction

Zipper Pile Weatherstrip .270" Backing - .300" Pile Height - 100' Roll

Replaces Old or Worn-Out Pile Weatherstripping in Doors and Windows. New Zipper Tooth Design Allows Pile to Easily Snap in from Above the Extrusion Slot. High Density Gray Pile with Double Center Fin.

Scranton Stealth Brackets for Integral Hinges 4 brackets included. These brackets help support the plastic pins used with the integral hinge pin system. These brackets help to reinforced the hinge pins so they do not break or the door breaking at the top and bottom.

Tactile signs comply with the signage requirements of the Americans with Disabilities Act.
6" x 8"
Grade 2 Braille

Tactile signs comply with the signage requirements of the Americans with Disabilities Act.
6" x 8"
Grade 2 Braille

Von Duprin EPT10 Power Transfer provides a way to transfer power through the edge of the door to the frame.   The EPT-10 has ten 24 gauge wires and includes all of the mounting hardware you need.

Von Duprin Part # EPT-10

Outswing For 1" Square Edge is designed for out swinging doors with a 1" thick square edged pilaster post.  It is constructed of cast stainless steel.  The manufactures part number is 40-8562308.

Toilet Partition Surface Mounted Hinge Set- Lh Outswing, Rh Inswing, Stainless Steel

Stainless Steel construction 1/8" thick. Outside hinge measurements are 3-1/4" wide by 2-29/32" high. 1-1/2" hole spacing up and down, and 2-3/8" right to left hole spacing. The four mounting holes are 1/4" diameter. This hinge set includes the top and bottom hinges. Also known as Bathroom Stall Gravity Hinge Set. See "More Views" for the handing diagram. Manufacturer part # 7113.

Mounting screws are included.

one way screw #10 x 5/8" long, 11/32" head x 3/16" tread. Use a flat head screw driver to install.

Lyon Metal Locker Rubber Bumper (3/8" X 1/2"). June 2006 - Current. Also known as 6785 or 6803.

Tactile signs comply with the signage requirements of the Americans with Disabilities Act.
6" x 8"
Grade 2 Braille

Interior steel equipment locker recessed Handle, The locker handle is constructed of stainless steel. The Locker handle is Ada approved and most commonly used these days. This product uses the lifter that connects to the lock bar to release the door from the frame of the locker. Also known as 3725, is4442.

Sargent 2828 / 2838 Center Case Cam

The Sargent 2828 / 2838 Center Case Cam is the Cam that the key cylinder actuates to open the door.   The Cam is located in the middle of the Center Case.  We can no longer get the retaining ring to hold it in place.

Sargent Part # 28-0109

Self-Adhesive Felt Strips, 1/8" thick x 1/2" wide x 5" long. Now sold individually.  Protect floor surfaces from scratces with felt strips. Easy to install, self adhesive. 

Push Bar 1' Diameter 422
Bar is made of solid aluminum, Stainless Steel or Bronze. The bar comes with thru bolts for mounting

Material Size 1 " round
Base 1" Round
Clearance 1-1/8"
Projection 2-1/8"

Please allow 4 weeks on Aluminum, Polished Brass, and Oil Rubbed Bronze. Stainless Steel and Polished Stainless Steel take about 2 weeks.

ASI Visual Display L Bracket-1-1/4" Lip

Used to hang marker, bulletin, or chalk boards

7/8" wide x 2-1/2" x 1-1/4" lip

The Dorma RTS88 Top Arm 8835 is for use on Double or Single Acting doors that have a 1" top rail.  This is the standard arm on the RST07 and RST10 packages.

Dorma Part # 8835

FEATURES

• Please note the factory will only sell in quantities of 10.
• Locks are individually keyed for single key access on a single lock
• Higher security 5-pin tumbler lock cylinder
• Rear mounted steel casing deters vandalism
• Locks have supervisory Control Key overide
• Each lock supplied with 2 keys
• Lock will work on both left and right hinged doors
• All Key Locks have a 5 year warranty from time of shipment
• 72 hour shipping available
  

APPLICATIONS

Fully retracting automatic spring latch for convenience

Truth 21088 Casement Window Keeper

This Truth Window Casement Strike is 4-5/8" long and made of stamped steel.

1/4-20 thread Leveler swivel nylon base glide. Stop wobbling of uneven floors with this Metal Furniture Foot.  1 1/8" base diameter and 1 1/8" stem length. Screw into a thread leg hole to reach your desired height. Combine with a tnut to install in wooden furniture legs. 

Norton Hook Up Boards for units made after 2009.  Available in 24 or 120 Volts.

Lyon Folding Chair Rear Leg Foot, base is 1 1/4" x 13/16" and the insert measurement is 3/8" x 3/4". This is Lyon part number 1593. 

Corbin Russwin ED5400 / ED4400 Top Latch

The Corbin Russwin ED5400 / ED4400 Top Latch is used on the Non Fire Rated ED5400 and ED4400 Exit Devices.

Corbin Russwin Part # 650F55-8

Window Strike 5/32" Thick Inline

1-3/8" hole spacing x 5/32" thick
White bronze construction with nickel plating.

Window Strike 7/32" Thick Inline

1-3/8" hole spacing x 7/32" thick
White bronze construction with nickel plating.

Toilet Partition Continuous Toilet Partition Hinge 54" With Spring Close Stainless Steel, Rh Outswing, Lh Inswing

Stainless Steel Construction 16 gauge (.060" thick). Hinge is 3" wide when laid flat, by 54" long. Holes are 9/32" diameter, spaced every 10-1/4" or so. Hinge can be raised up 3/8" for emergency entry. Hinge pin is 1/8" diameter. This Continuous Hinge is for Right Hand Outswing, and Left Hand Inswing, see handing diagram under "More Views". Also known as a Full Length Bathroom Stall Continuous Hinge. Manufacturer part # 7969.

Lyon Metal Locker Locking Bar Spring Wire Catch, Old Style spot welded on lock bar. Used in April 1953 - February 1980.
4-3/8" overall length. Also known as 6520, 75046, ly6787, ll1743.

Von Duprin Strike 248L-4

The Von Duprin 248L-4 Strike is used as a Bottom Strike on the 2227, 8827, 9927, and 9827 Surface Vertical Rod Panic Devices. The 248L-4 strike measures 9/16" wide by 2-1/2" high with a hole spacing of 1-7/8. The strike projects out 3/8".

Ships with shim and mounting screws

Von Duprin Strike 248L-4

Burnished steel construction

Knickerbocker Partitions Top Hinge

Chrome plated Zamac die cast construction. The wrap around dimension is 1-1/4" wide by 1-3/4" high and 11-16" deep.The hole spacing is 1-1/8" on center. The lug projects out 1-3/8" to center hole with a 1/4" bushing diameter. Also known as a Bathroom Stall Pivot Hinge - Top 1-1/4". Manufacture part # 3910.

a=1-11/16"

The 1 inch diameter Decorative Cap comes in two different tread sizes 1/4-20 and 5/16-18.  The Cap measures 1 inch diameter by 3/8 inch thick. Stainless Steel base material.

This is the same trusted Von Duprin 99 with Electric Latch Retraction, also known as EL.

The EL feature allows for the remote unlatching of exit devices. A control station operator can flip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. A powerful, continuous duty solenoid retracts the latch bolt, either for momentary unlatching, or for extended periods of time. The EL feature is an alternative to manual dogging.

The rim device is non-handed.
A power supply is required for operation, see related products.
Ships with all the mounting screws and the 299 Strike.