Search results for: 'locker number tabl 1 3 hold stop'

Von Duprin Strike 304L

This Von Duprin Strike is used for the bottom latch of the 2227, 8827, 9827 and 9927. The strike measures 1-7/8" by 1-7/8" outside dimension of the square flange, with an inside dimension of 1-1/8" by 1-1/8". The part that is inserted into the floor is 1-3/8" x 1-3/8" and drops down 13/16". Also known as a Von Duprin Floor Mounted Mortise Strike.

Alcove One Ear Bracket Panel Kit for 1/4" Offset. This kit is used for panel to pilaster 1/4" offset and for 1" panel to wall bracket cast stainless steel plated. Security screws included. Also known as 615363.

Door Pull 23

This door pull features an 8" center to center screw dimension. The handle ships with thru bolts and finish washers. Also known as a Door Handle, or Door Grip.

3/8" x 1-1/4" handle cross section
8" centers
14" overall length
1" diameter base
1-7/8" projection

Finishes

Indoor Flag Stand - 1". These cast stands are designed to compliment any flag set. Easily movable, these are the most practical stands for general use. This flag base weighs 15 pounds. The flag stand is 12" diameter and 6" high. 

The Anodized Aluminum Neoprene Door Shoe is an aluminum U channel to mount on the bottom of doors.  The channel is 1 inch deep with a 1/2 inch neoprene seal on the bottom.  Fits over the bottom of 1-3/4 inch thick doors.  Ships in 36 or 48 inch lengths and comes with #6 x 3/4 inch stainless steel screws.

Toilet Partition Surface Mounted Black ADA Slide Latch Set W/ Indicator

Stamped stainless steel construction with a Black Finish. Slide lock measures 4-3/16" long by 1-1/8" tall by 15/32" thick. The mounting plate has mounting screws 1-1/4" on center and is 2-15/32" long. The lock projects out 1-3/16" from the face of the door. The indicator is 2" in diameter and 13/32" thick. The keeper is 3/4" wide by 1-7/16" tall by 1/16" thick. Commonly known as a Bathroom Stall Surface Mounted ADA Slide Lock and Toilet Partition Locks. Manufacturer part # 6065. For 1" thick doors.

Shipped with mounting screws.

3-1/2" straight spindle thread is 18 tpi. 2-1/4" knob

Bobrick Partition Bottom Door Insert For 1" Door

Chrome plated Zamac die casting. The door insert outside measurements are 2-5/16" wide by 1-5/32" deep by 1-3/16" tall. The inside dimensions are 1" and the hex hole measures 3/4". The round hole measures 5/16". Also known as a Bathroom Stall Door Insert - Bottom 1". Manufacture part # 2490

Universal Bleacher Spring 2-1/2" long.

Truth 24.30 Sash Lock

The Truth 24.30 Sash Lock has a hole spacing of 3-13/16" and the locking lug projects 1-3/8"

Truth 11.14 Double Pull Awning Operator.

Attaches to window at two points 9" apart. 25" spread with operator is in closed position. We some times see the numbers 40245, 30897 or 30897A stamped on the arms.

Sash Hooks and matching color handle included.

Sargent Knob Return Spring

This Sargent Knob Return Spring measures 1-1/16" overall length by 3/16" diameter

Sargent Part # 97-0050

Yale 2100 Exit Device

Door Opening Width:
-36 for 30" - 36" (76.2cm - 91.4cm) doors, Actual width is 31-3/4"
-42 for 36" - 42" (91.4cm - 107cm) doors, Actual width is 37-3/4"
-48 for 36-1/2" - 48" (92.7cm - 121.9cm) doors, Actual width is 43-3/4" 
Door Thickness: 1-3/4" (44mm) standard.
Minimum Stile Width: 4-1/2" (114mm)
Projection: 2-1/2" (64mm) active, 1-3/4" (44mm) depressed

Aluminum is in stock, Dark Bronze has a 2 week lead time

Tubing is 1″ diameter x 20 gauge with a satin finish. 42" Length will be as specified. Rod is held captive by flanges when installed properly. Rod may rotate in flanges if turned by hand. Correctly installed rod and flanges will support specified shower curtain(s) hung on hooks 1200-SHU or others. Rod will bend and pull from flanges if significant body weight is suspended.

Tubing is 1″ diameter x 20 gauge with a satin finish. 72" Length will be as specified. Rod is held captive by flanges when installed properly. Rod may rotate in flanges if turned by hand. Correctly installed rod and flanges will support specified shower curtain(s) hung on hooks 1200-SHU or others. Rod will bend and pull from flanges if significant body weight is suspended.

• Handed
• Top, header mount
• Bottom, base plate mount
• Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
• Maximum door load 200 pounds
• Vertical adjustment range 3/16", with positive locking

Handing diagram

Plate Top Single Wheel Caster - Non Swivel (Rigid)- 5" Wheel, 1-3/4" x 3" Hole Spacing. Zinc finish with black rubber wheel. Tread for both carpet and non carpet areas available. 

KKAC61 hard tread for carpet

KKAC62 soft tread for non carpet surface

The Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase is also known as Part # P6000IR.

This Klauber Gear Motor Single Phase features:

• ¼ horsepower
• 115 volts
• RPM 12
• Amps 4

The powerful Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase is designed specifically for folding bleachers, providing reliable performance and durability. With its ¼ horsepower, it delivers the necessary strength to operate bleacher systems smoothly and efficiently. The Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase runs on a single-phase power supply of 115 volts, making it suitable for a variety of settings, including schools, gyms, and auditoriums.

As a facility manager, you are probably sure to check the bleacher hardware in your building periodically and replace any worn parts to maintain safety standards. Our online store has replacement parts readily available to order for this purpose. Regular maintenance is crucial for the longevity of your bleachers. We recommend scheduling routine inspections to identify any potential issues before they become major problems. This proactive approach not only enhances safety but also minimizes downtime, allowing your facility to operate smoothly. Whether it's for sporting events, school assemblies, or community gatherings, well-maintained bleachers contribute to a safe and enjoyable environment.

The installation process of this Klauber Gear Motor Single Phase is straightforward, allowing you to quickly set up and start using your bleachers without unnecessary delays. The Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase is built to withstand the rigors of frequent use, providing peace of mind for facility managers. Whether you are upgrading existing bleacher systems or installing new ones, the Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase is an excellent choice for ensuring safety and convenience in any venue.

For more information on the Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase or to purchase, please feel free to contact us. We always encourage you to ask us questions in order to get the best performance from your Klauber Folding Bleacher Gear Motor 1/4 Hp Single Phase.

For use on commercial applications.
• Exceeds OSHA and BHMA strength test requirements.
• Packed with square head iron lag screw, expansion shield and screws.
• Cast Aluminum construction.

Dimensions
Base Diameter: 3-1/8"
Base to Rail Center: 3-1/8"

Global Partitions Surface Mounted Slide Bolt Latch Chrome Plated

Zamac die cast construction, polished chrome finish. Latch base is 4-1/2" high with 3-1/2" hole spacing. Latch bolt is 3-3/32" long by 1" wide by 3/16" thick. The latch bolt clearance is 9/16" from the back of the base to the under side of the latch bolt and projects out 15/16". The latch projects out 1-9/16" from the face of the door when installed. Also known as a Bathroom Stall Surface Mounted Slide Bolt Latch. Manufacture part # 5050.

Shipped with mounting screws.

Used by accurate and global

Global Partitions Top Hinge For 1-1/4" Round Edge Post

Chrome plated Zamac die cast construction. Pivot hinge is 2-3/16" tall by 1-1/4" wide. The slot that wraps around the post is 1-1/4" wide and 11-16" deep. The hole spacing is 1-1/2" on center. The lug projects out 1-1/2" and is 1/2" thick. The bushing on the lug is 3/8" diameter. Also known as a Bathroom Stall Pivot Hinge Top 1-1/4". Manufacture part # 3510.

Shipped with mounting screws.

A=1-7/6"

Truth 16.52 Sash Lock. A very common sash lock that tends to fail because the plastic slide breaks due to incorrect installation at the window manufacturer or being forced when there is a obstruction in the window opening. The new replacement model has a thicker plastic slide. Because the slide is thicker, the keeper, part # Wi41268 and Wi41269 might have to be shimmed with small washers.

Common numbers found on this sash lock are 21328 and 45189

Non handed (can be used on right or left hand windows).

Magnuson Mega Rak

Mega Rak can be set up to accommodate large numbers of coats then folded and stored in a small space until needed again. A popular choice for meeting, rental, hospitality, and convention use, the MR-801 Series opens to 8 feet and features vinyl coated wire shelves which accommodate up to 144 Coats on the K-73 triple prong vinyl coated steel hooks.

Charcoal Grey frame with Medium Grey Shelf.

Open dimensions: 60" high x 25" wide x 97" deep
Closed dimensions: 81" high x 25" wide x 18" deep

All units feature 4" diameter ball bearing locking casters and are shipped completely assembled, ready to use, via common carrier.

Wayne Bleacher Wheel, 1/4"x13/16"x3". Soft rubber wheel 100# load capacity. Known as 262wn.

Brunswick Chair Replacement Caps. Metal cap measures 1-1/16" outside diameter by 1" inside diameter by 3/8" tall. This Chair Tip is designed to be used on Brunswick Chairs. 

Doromatic 2390 Fixed Cover

The Doromatic 2390 Fixed Cover also known as the center case cover. The cover is 1-1/2" wide by 3-7/16" high and projects out 2 inches. The mounting screws are 3" on center.

Doromatic / Falcon Part # COVER.127 or PB341

Dorma part # 7414ARP689

3/4" X 10-1/4" Hole Spacing

Gravity Door Coordinator

When active door is open, coordinator prevents active door from closing until inactive door bypasses. Closing of inactive door causes strike plate on top of door to contact cam and lift arm, allowing active door to close. As inactive door continues closing, roller rides over strike plate on to door bracket, holding arm above active door.
Non-handed.
Gravity action arm and door bracket are adjustable on the job for ease of installation. Rubber roller provides quiet and efficient operation, and helps protect the astragal and doors from damage. Nylon roller on short arm glides smoothly over door bracket and strike, ensuring silent operation. Made of forged brass.
COR7G-26D for use on pairs of doors with astragal on active door up to 4' or with astragal on inactive door up to 3'4" or with astragal on both doors up to 2'10" Brushed Chrome Finish.

Ives part # COR7G-26D 7" Arm Projection

Gravity Door Coordinator 9"

When active door is open, coordinator prevents active door from closing until inactive door bypasses. Closing of inactive door causes strike plate on top of door to contact cam and lift arm, allowing active door to close. As inactive door continues closing, roller rides over strike plate on to door bracket, holding arm above active door.
Non-handed.
Gravity action arm and door bracket are adjustable on the job for ease of installation. Rubber roller provides quiet and efficient operation, and helps protect the astragal and doors from damage. Nylon roller on short arm glides smoothly over door bracket and strike, ensuring silent operation. Made of forged brass.
COR9G-26D for use on pairs of doors with astragal on active door over 4' or with astragal on inactive door over 3'4" or with astragal on both doors over 2'10" Brushed Chrome Finish.

Ives part # COR9G-26D 9" Arm Projection

The 591 manual flush bolt is for wood doors and is UL listed. It is constructed of solid brass. The face plate is 1 x 6-3/4 inches. The mortised body is 6 inches high by 1-3/8 deep by 1 inch thick. The screw spacing is 1/2 by 6-1/4 inches on centers.

Partition Top Hinge Casting

Unplated Zamac die cast construction. The outside dimensions of the top hinge casting are 3-7/16" high by 2-3/8" wide by 1-5/32" deep. The casting features four holes, two of them are 3/8" diameter, one is 7/32" diameter and the fourth is a threaded hole for a 5/16-18 screw. The two U channels have spacings of 13/16" and 1" on the other. Also known as a Bathroom Stall Door Insert - Top 1". Manufacture part # 4546. Used with AMPCO and Metpar Toilet Partitions.

Toilet Partition Surface Mounted Hinge Set -Rh Outswing, Lh Inswing, Stainless Steel

Stainless Steel construction 1/8" thick. Outside hinge measurements are 3-1/4" wide by 2-29/32" high. 1-1/2" hole spacing up and down, and 2-3/8" right to left hole spacing. The four mounting holes are 1/4" diameter. This hinge set includes the top and bottom hinges. Also known as Bathroom Stall Gravity Hinge Set. See "More Views" for the handing diagram. Manufacturer part # 7123.

Mounting screws are included.

Improve safety and prevent worn carpet edges on steps; for new or renovation work. Butt 1/4” to 3/8” thick carpet against both the top and bottom lips of butt-type carpet nosing. Standard 8’ lengths; easily cut to size. Install with #400 Neoprene Contact Cement or #300 Water-based Contact Adhesive.

SPECIFICATIONS:

Furnish and install No.140 Koroseal Vinyl Ribbed Carpet Nosing; 3-1/8” deep; 2-1/2” nose depth; square adjusta-nose. Lap 5/16”, 1/4" or 3/8” carpet over lip on both the step and riser. Select from standard colors of black, brown.

Shipping:   Due to shipping costs, this product is shipped in two 48" sections

Push Plate 70

.125" thick with 4 beveled edges. Base material is either aluminum, brass, bronze or stainless steel depending on the finish. This would be considered a premium push plate.

Finishes