Search results for: 'grab 8 door body door harden'

The Von Duprin 88 Center Case Rivet 090002 is also known as the Latch Tail Rivet used on the 88 Rim Device.  The Rivet fits into the spring and into the Latch Tail 050500.  The rivet measures 1-1/4 inches long less the head, with a 1/8 inch diameter.  We sell this piece individually.

Hardware packets are based on 4' x 8' boards.

Package includes 4 plastic anchors, 4 drill and tap screws, and 4 each of the #2LCLIP and #3LCLIP

HD-408-BB is used for boards with item # prefixes: AA, AB, AF, AM, AN, AP, CA, CB, CT, CW, LA, PR, WB, WF, WN, WP

HD-408-WC is used for boards with item # prefixes:AW, LW, MW, WM, WS, WR

HD-408-AC is used for boards with item # prefixes: AS, MA

Partition Continuous One Ear Wall Bracket For 1"Panel Aluminum

Constructed of extruded anodized aluminum. Base is 2-5/8" wide by 57-1/2" long, with screw holes every 13" or so. The legs project out 2-3/4" with the thru hole at 2-3/8" from the back of the base. The legs have a clearance of 1" for 1" thick panels. Sometimes known as Bathroom Stall Continuous One Ear Wall Bracket. The manufacturers part numbers are 2334, one ear 1" x 57, and 650-9750-58. These brackets are shipped with all the needed fasteners.

Toilet Partition Continuous One Ear Wall Bracket For 1 1/4" Panel Aluminum

Constructed of extruded anodized aluminum. Base is 2-5/8" wide by 57-1/2" long, with screw holes every 13" or so. The legs project out 2-3/4" with the thru hole at 2-3/8" from the back of the base. The legs have a clearance of 1-1/4" for 1-1/4" thick panels. Sometimes known as Bathroom Stall Continuous One Ear Wall Bracket. The manufacturers part numbers are 2354, and 650-9186-57. These brackets are shipped with all the needed fasteners.

Jackson 1285/1295 Cover Package

Jackson part # 30-2674-313 and 30-2674-628 Cover Plate for use on the 1285 and 1295 devices..  Plates measure 2-11/16" x 7-1/2 and 2-11/16" x 2-1/8", two plates in each package.

Jackson Part #'s 30-2674-313 and 30-2674-612

B-274 Bobrick toilet tissue dispenser for double roll. The unit is made of a cast aluminum satin finish with a plastic spindle that is theft resistant. Holds up to one roll 6" diameter. The unit measures 12-1/2"w x 4-7/8" projecting out from the wall. This also has a controlled delivery.

Introducing American Specialties Stainless Steel Frameless Mirrors. Constructed of 20 gauge stainless steel, polished to a #8 mirror finish. Plate is mounted on a 1/4" thick concealed tempered Masonite backing plate, with holes in each corner for mounting. Also known as 8026 series mirrors.

405CR Vinyl Stair Tread Risers

Plain color cove risers match Koroseal vinyl stair treads; or use a contrasting riser with vinyl or rubber treads; easily trimmed in height and length; savings in installation are substantial; cove risers are same sizes as stair treads.

SPECIFICATIONS:

Furnish and install No 405CR Koroseal vinyl coved stair riser; 1/8” thick, 7” high with 5/8” toe; ribbed back. Select standard length of 18”, 24”, 30”, 36”, 42”, 48”, 54”, 60”, 72”, 84” or 96”. Select standard solid color of Brown, Sand, Gray or Black.

Sanymetal Partitions Coat Hook Bumper

Chrome plated Zamac die casting construction. Coat hook bumper projects out 3" and has a rubber insert. The hook projects out 1-7/32". The coat hook bumper base is 1-7/16" wide by 2-1/4" high with a hole spacing of 7/8". Also known as a Bathroom Stall Hook. Manufacture part # 4000.

Ives RL32 Nylon Roller RLPART.1045

This replacement Nylon Roller and Rivet Package is for the Ives RL32 Roller Latches.  The Roller measures 3/4" high by 5/8" diameter.  The Rivet measures 15/16" long and is threaded on one side.

Ives Part # RLPART.1045

The 620D Rubber Stair Tread comes in two versions, Square Nose and Round Nose. This page is for the Round Nose, Search 620DSN for the Square Nose Version. This tread offers an 1/8" nose thickness, with a 3/4" radius. They are designed for interior use.

Toilet Partition Urinal Screen Bracket Chrome Plated

This bracket is for any thickness panel. The bracket is 2 separate pieces. The base is 1-1/2" x 1-1/2". The base mounting hole is 1" from the inside face of the leg face. The bracket projects out 3-1/2", and the holes are at 3-1/8" and 2-1/8" from the mounting face. The brackets are made of a zamac die cast material and polished chrome plated. This bracket is also known as a Two Piece Bracket - X-long Two Holes, Toilet Partition Bracket, or Bathroom Stall Extra Long Bracket. The manufacturers part number is 1320 or 650-6434. The bracket is shipped as two pieces plus all of the fasteners.

Flush Metal Partitions Nylon Cam

White nylon construction. The partition cam head outside diameter is 23/32" and the inside diameter is 1/2". The cams cylinder is 1-13/32" long with a diameter of 5/8". Also known as a Bathroom Stall Cam. Manufacture part # 98275.

FIAT BOTTOM HINGE FOR 1-1/4" SQUARE EDGE PILASTER POST CHROME PLATED Chrome plated Zamac die cast construction. The hinge measures 2-1/4" high by 1-1/4" wide and the hole spacing is 1-1/2". The U channel is 2-1/4" by 1-1/4" by 1" deep. The lug projects out 1-5/8" by 1/2" thick with a 5/16" diameter bushing. Also known as a Fiat Bathroom Stall Pivot Hinge Bottom 1-1/4". Manufacture part # 3290.

Shipped with mounting screws.

a=1-5/8"

also known as General, American Sanitary, Flush Metal, Fiat Tiolet Partition 91000P, 9AM280, 9FL700

American Sanitary Partitions Coat Hook Bumper

Chrome plated Zamac die casting construction. Coat hook bumper projects out 3" and has a rubber insert. The hook projects out 1-7/32". The coat hook bumper base is 1-7/16" wide by 2-1/4" high with a hole spacing of 7/8". Also known as a Bathroom Stall Hook. Manufacture part # 4000.

White nylon construction. The partition cam head outside diameter is 23/32" and the inside diameter is 1/2". The cams cylinder is 1-13/32" long with a diameter of 5/8". For use with a 1/2" pintle. Also known as a Bathroom Stall Cam. Manufacture part # 98275.

Replaces old style hinge pin. If you have old style you must buy upper hinge too. 631400 new, used with 9hh350, 9hh300, 9hh550, 9hh500 used with arch also. This product uses a phillips head screwdriver, old style was a torx head. The dimensions are 3/8" diameter by 1-1/2" height.

Concealed Latch Keeper Bumper Outswing Cast Stainless Steel

Cast Stainless Steel casting. The strike and keeper is 1-1/4" high by 1-3/4" deep by 1/8" thick. The stop is 1/2" deep by 1-1/4 wide with a rubber insert. Also known as a Bathroom Stall Strike and Keeper Outswing Flat. Manufacture part # 5643.

Shipped with mounting screws.

Falcon Monarch Bottom Bolt Guide Assembly

The Falcon Monarch Bottom Bolt Guide Assembly 650387 is used the 19-V, 24-V, 25-V and the XX-V Bottom Rod.  The Guide Assembly measures 1-7/8" tall by 1" wide and projects 1-9/16" at the widest projection.   The Bottom Bolt Guide is made of zinc plated steel.

Falcon Monarch Part # 650387

Adams Rite New Style Metal End Cap for the 3700, 8700 and 8800.
The black cap measures 2-3/8" high x 1-1/2" wide x 1-1/4" projection.  Newer metal end cap will replace the old plastic ones.

Adams Rite Part # 41-0902-03-IP

Cast Stainless Steel Bottom Hinge for 1-1/4" Sq Edge

Cast stainless steel construction. The hinge measures 2-1/4" high by 1-1/4" wide and the hole spacing is 1-1/2". The U channel is 2-1/4" by 1-1/4" by 1" deep. The lug projects out 1-5/8" by 1/2" thick with a 5/16" diameter bushing. Also known as a General Bathroom Stall Pivot Hinge Bottom 1-1/4". Manufacture part # 3293.

Shipped with mounting screws.

a=1-5/8"

This is a replacement for the Zamac Die Cast hinges for General, American Sanitary, Flush Metal and Fiat Partitions.

Corner Guard CG-20 2" x 2"

90 degree 2” x 2” vinyl corner guard with aluminum retainer.  Vinyl flex action absorbs impact, and is .085” thick, the aluminum retainer is .062 thick.  Each corner guard includes the end caps.  Available in 4, 8 and 9 foot lengths.  Corner guards are shipped with a top and bottom end cap.

General Partition Concealed Latch Knob & Cover

Zamac die cast construction with polished chrome plating. Outside diameter of the knob and cover are 1-5/8" with the inner ring diameter of 1-1/4". Also known as a Bathroom Stall Concealed Latch Cover and Knob Assembly. Manufacture part # 1390, 6140.

Truth Telescoping Pole Hook Only

Replacement Pole Hook Drive for the Wi10637 for the Truth Telescoping Pole Crank.  The Hook Adapter measures 1" wide, overall length is 2-3/8" including female insert that fits into pole.  The insert spline is 11/32" with a 1/2" diameter.

Truth Part # 10453

Ives RL30 and RL1152 Nylon Roller RLPART.1025

This replacement Nylon Roller and Rivet Package is for the Ives RL30 and RL1152 Roller Latches.  The Roller measures 3/4" high by 5/8" diameter.  The Rivet measures 1-1/16" long and is threaded on one side.

Ives Part # RLPART.1025

Interkal riser combo roller & bracket. The black plastic roller dimension is 1-1/4" diameter by 1-5/16" by 1/2" center hole. The plate is 1-7/8" by 3-3/4" long and the two hole dimensions are 5/16". Used with Interkal bleachers known as 176383.

Chrome Plated Two Ear Urinal Bracket For 1" X 1-1/2" X 3-1/2

This bracket is usually used on Urinal Screens, which are the walls between men's urinals, to hold the partitions to the wall. The bracket is made of a zamac casting that is then chrome plated. The bracket base measures 1-1/2" x 4", with a 3" center to center hole spacing. The bracket projects out 3-1/2", with the mounting holes at 2-1/8" and 3-1/8" from the base. The holes used to mount the bracket to the wall and to the urinal are 1/4" diameter. The 1280 Bracket is sometimes called a Bathroom Stall Bracket, Toilet Partition Bracket, Two Wing Bracket, or Urinal Screen Bracket.

For 1" thick panels

Chrome Plated Two Ear Urinal Bracket For 1-1/4" X 1-1/2" X 3-1/2

This bracket is constructed of zamac die cast material that is then polished chrome plated. The base is 1-1/2" wide x 4" long, with two screws 3" on center. The legs project out 3-1/2" with the thru screws at 3-1/8" and 2-1/8" from the base. The 6 holes are 1/4" diameter. This bracket is also known as a Toilet Partiton Bracket, Bathroom Stall Bracket, Two Ear Extra Long Bracket, Two Wing Bracket, Urinal Screen Bracket X-Long. The manufacturers part # are 1330, and 650-6449. The bracket includes all the fasteners.

This bracket is for a 1-1/4" thick panel

892 Mop and Broom Holder - 18 gauge type 304 stainless steel channel projects 3-1/4" from the wall, fitted with spring-loaded, serrated rubber cams to hold mop and broom handles from 7/8" to 1-1/4".

4 holders

The 1010R Rubber Stair Tread features a Rib Design, with grooves all along the fall line.   The round nose is not tapered or adjustable.  The nose is 1/8" thick and tapers to 3/32" at the very back.  The radius of the nose is 3/4". They are designed for interior use.

Bottom Partition Hinge For 1-1/4" Round Edge Post Or Pilaster

Chrome plated Zamac die cast construction. The hinge measures 1-1/4" deep by 2-1/8" high by 1-7/16" wide. The U part of the hinge measures 2-1/8" high by 1-1/4" deep with a slot depth of 11/16". The hole spacing is 1-1/2". The lug projects out 1-3/32" and is 1/2" thick with a 5/16" diameter hole. Also known as a Bathrrom Stall Pivot Hinge - Bottom 1-1/4". Manufacture part # 4040. Used on Ampco and Metpar Metal Partitions.

Shipped with mounting screws.

A=1-7/16"

The 520S Rubber Stair Tread has a 1/4" nose thickness which tapers down to 1/8" at the back.  The nose drops down 1-9/16", and the nose is not adjustable and is not tapered. They are designed for interior use.

The 605CR Rubber Coved Riser goes in the back of the step and acts as a kick plate in the matching color of your stair treads.  The Riser is 7" tall and features a 5/8" cove to aid in cleaning of the back of the step.