Search results for: 'grai 8 duty block door handed'

Sargent Door Closer Heavy Duty Compression Holder Arm

Forged Steel Arm 11-1/4" long, non handed, will work left or right for Parallel Armed Sargent Closers.  Permits 105 degree opening with built in compression stop and holder mechanism.

Sargent Part # 25-CPSH

LCN Door Closer Extra Duty Arm

Non-handed parallel arm features solid forged steel main
arm and forearm with stop in soffit shoe.

Specify your current closers model number when ordering. Not all
of the LCN closers have the same shape spindle on the door closer
cylinder. LCN Part #'s: 1260-3077EDA, 1460-3077EDA, 4040-3077EDA, 4110-3077EDA

Ives Dome Door Stop 1-3/8" FS438

Features:

• For doors with threshold or undercut doors.
• Heavy-Duty Cast Dome Stops constructed of brass, bronze or aluminum.
• Gray, non-marring rubber bumper.

Overall hgt 1-3/8"
Base Hgt 9/16"
Base Diameter 1-3/4" x 2" Oval

Floor Mounted Door Stop Heavy Duty 540

This Floor Mounted Door Stop is a personal favorite. It is extremely heavy duty, and is ideal for areas of high vandalism. Includes the 4-1/2" lag bolt & lag shield. The rubber base is 3" in diameter and is 2-5/8" high.  Uses a 3/4" diameter hole for the lag sheild.

Floor Mounted Door Holder Heavy Duty 541

3" Diameter
3" Height
Includes the 4-1/2" lag bolt & lag shield.

• Standard top pivot for heavy-duty offset
pivot sets
• Heavy-duty needle bearings are standard
• Non-ferrous base metal
• 3/4"(19mm) offset (measured from
centerline of pivot to face of door)
• Furnished with wood and machine screws

Handing diagram

Ives Dome Door Stop 1" Height FS436

Features:

• For doors without threshold.
• Heavy-Duty Cast Dome Stops constructed of brass, bronze or aluminum.
• Gray, non-marring rubber bumper.

Overall hgt 1"
Base Hgt 3/16"
Base Diameter 1-3/4" x 2" Oval

Rubber Chair Tips For Legs With An Outside Diameter Of 7/8"

Rubber chair tips for round legs

For round legs

For Hampden, Krueger and Samsonite chairs

Available in Black or Gray

Rubber Chair Tips For Chair Legs With An Outside Diameter Of 5/8". For Hampden, Krueger ans Samsonite Chairs. Save your floors from expensive damage by using these chair tips. Available in Black or Gray.

Rubber Chair Tips For Chair Legs With An Outside Diameter Of 1-1/8". Rubber feet are for round chair legs with an outside diamter of 1 1/8". Tips are for Hampden, Krueger and Samsonite chairs. Available in Black or Gray.

The Doromatic 2390 Anchor Block Assembly is used to connect the push bar to the device channel.

Discontinued December 2024

Plastic chair tip for 5/8" diameter round tubing chair legs. Protect your floors against scratches and marks. These chair tips are available in tan, gray and black in a variety of sizes. Chair tips help prevent chair legs from coming through and damaging your floors. For Krueger Chairs, Tables and other furniture where the leg has a 5/8" outside diameter. 

Available in Tan, Gray, and Black

Reinforced Rubber Chair Tips For 5/8" Outside Diameter Round Legs

One of the biggest problems with rubber chair tips is the metal leg punching through the rubber feet. This happens because the metal chair legs are sharp and blunt. By installing a chair tube cap first, the rubber chair leg has more of a surface area to displace the weight.

Part # - Color
RCT62BTC - Black
RCT62GTC - Gray

Reinforced Rubber Chair Tips For 7/8" Outside Diameter Round Legs

One of the biggest problems with rubber chair tips is the metal leg punching through the rubber feet. This happens because the metal chair legs are sharp and blunt. By installing a chair tube cap first, the rubber chair leg has more of a surface area to displace the weight.

Part # - Color
RCT87BTC - Black
RCT87GTC - Gray

Plastic chair tip for 7/8" diameter round tubing chair legs. Protect your floors against scratches and marks. These round chair tips are available in tan, gray and black in a variety of sizes. Chair tips help prevent chair legs from coming through and damaging your floors. For Krueger Chairs, Tables and other furniture where the leg has a 7/8" outside diameter. 

PCT87T Tan

PCT87G Gray
PCT87B Black

Marsh Map Rail 2" x 8' Insert, 3 Pack

MR2T8 Tan
MR2G8 Gray

Plastic chair tip for 1 1/8" diameter round tubing chair legs. Protect your floors against scratches and marks. These chair tips are available in tan, gray and black in a variety of sizes. Chair tips help prevent chair legs from coming through and damaging your floors. For Krueger Chairs, Tables and other furniture where the leg has a 1-1/8" outside diameter.

PCT112T Tan

PCT112G Gray
PCT112B Black

Heavy duty knob set. Replaces the Corbin #1419 with #32 spindle.
Outside knob is pinned to spindle and inside knob is held by
two 5/16" case hardened set screws. Spindle is on 3/8" diameter
center on outside half and inside spindle is threaded 3/8-20

LCN Door Closer Cush-n-Stop Arm

Non-handed parallel arm features solid forged steel main
arm and forearm with stop in soffit shoe.

Specify your current closers model number when ordering. Not all
of the LCN closers have the same shape spindle on the door closer
cylinder. LCN Part #'s: 1260-3077CNS, 1460-3077CNS, 4040-3077CNS, 4110-3077CNS

Standard 4110 series closer shipped with EXTRA DUTY arm, standard plastic cover, 4110-201 FIFTH SCREW SPACER and self reaming and tapping screws. Sized cylinders adjustable for interior doors to 5’0” and exterior doors to 4’0”. Non-sized cylinder adjustable for interior doors to 4’6” and exterior doors to 3’6”. Closer mounts parallel arm, specify right or left swinging door. 4111 cylinder meets ADA requirements.

We ship the 4111 EDA

Handing diagram

Ives Wall Bumper Heavy Duty WS402CVX

Features:
• Constructed in heavy-duty cast brass or aluminum base.
• Special retainer cup makes rubber tamper resistant.
• The WS402CVX unit is designed with a convex rubber bumper packed with screw and
drywall anchor.

2-1/2" diameter with 1" projection

The offset door pull 44 is 5 inches by 12 inches.  It offers a 2 inch clearance with a 2-1/8 inch projection.  The mounting holes are 10 inches on centers.  The base block is 1 inch by 12 inches.

Toilet Partition Heavy Duty Vault Hinge Set Stainless Steel For 3/4" Or 1" Thick Doors

Stainless steel construction. For 3/4" to 1" thick doors and 3/4" to 1" posts and pilasters. Also known as a Bathroom Stall Roller Bearing Hinge Set. Used by all of the Toilet Partition manufactures on there Solid Plastic (HDPE) Restroom dividers. Manufacture part # 7813.

Shipped with screws.

Dome Door Stop 1-5/8" Height 521

Forged brass construction with a gray rubber bumper. 1-3/4" diameter x 1-5/8" High x 1/4" Base thickness, US26D-Brushed Chrome finish only.
Supplied with wood screws and machine screws with anchors

Ives Wall Bumper Heavy Duty WS401CCV

Features:

• Special retainer cup makes rubber tamper resistant.
• Constructed in heavy-duty cast brass or aluminum base.
• The WS401CCV unit is designed with a concave rubber bumper which avoids damage to ocks with projecting buttons, packed with wood screw and plastic anchor.

2-1/2" diameter with a 1" projection

The 4040SE Sentronic® is a heavy duty, non-handed, nonsized closer/holder designed to provide single point hold-open for fire and smoke barrier doors. The door is held open until current interruption releases the
holding mechanism and the door closes. Single lever (track) arm closer is specifically designed for interior doors. Choice of finishes, track functions, and installation accessories meet virtually all life safety requirements.

Falcon Spring-n-Stop Hold Open Arm, non handed, extra duty forged parallel arm includes an integral spring stop and non-adjustable forearm assembly for high volume traffic or abusive conditions.

Function is the Doromatic/Falcon Door Closer Model

Vinyl Stair Treads GS365 with Grit Strip

This is one our highest volume vinyl stair treads. Heavy duty to stand up to most applications with the safety of inlaid grit strips. Made in the USA

SPECIFICATIONS:

Furnish and install No. GS365 Koroseal Vinyl Stair Treads
Grit-Strip rib design stair treads; 7/32" thick, 12" deep; 1-1/4" square nose; two black* 1" wide abrasive Grit-Strips inlaid in tread, 1" from front edge, spaced 1-1/4" apart; contains no asbestos fiber; made of first quality homogenous vinyl, color throughout thickness; free from imperfections which might lessen serviceability. Meets Federal Specs. RR-T-650E Type B. Select standard length of 36", 42", 48", 54", 60", 72", 84" or 96". Select standard solid color of Brown or Gray.

DR-CT DIAGONAL RIB CARPET TILES
An attractive and functional entrance matting alternative; heavy duty modular carpet tile with excellent scraping and dirt removal properties for high traffic areas. Designed for interior use in entrances, vestibules, lobbies, between double doors, on ramps or in elevators.

Install in a recess or on the surface. Our easy release adhesive allows you to remove worn or damaged tile which is easily re-adhered. Tile can be switched to decrease traffic patterns; lasts longer, looks better. Vinyl or Aluminum beveled edging available.

3/8" thick; 19-11/16" x 19-11/16" square tile; diagonal rib pattern woven of 100% polypropylene pile yarn with a bitumen backing.

SPECIFICATIONS--No. DR-CT

DR-CT Diagonal Rib Carpet Tiles made of 100% polypropylene pile yarn with a bitumen backing in areas as indicated on drawings. Tile shall be of first quality commercial grade carpet, free of surface defects. Install tile in an alternating rib parquet pattern in indicated recess with recommended easy release adhesive, (or on surface area using vinyl edging or aluminum beveled frame). Tile shall be 3/8" thick, 19-11/16" x 19-11/16" square carpet tile. Select from standard carpet colors of Cranberry, Blue, Beige, Teal, Gray, Chocolate or Charcoal.

one DR-CT Diagonal Rib Carpet Tile covers 2.69 square feet

The concealed 2030 Series Pacer® is a heavy duty closer designed to fit in a narrow, minimum 1 3/4” aluminum transom. The single lever arm and roller assembly provide smooth, quiet door control and the choice of finishes and track functions meet virtually all architectural requirements.

Specifications

• Standard 2030 series closer shipped with standard arm, standard track, mounting/finish plate, and wood and machine screw pack
• Sized cylinders for interior doors to 4’6” and exterior doors to 3’6”
• Handed for right or left swinging doors
• Aluminum frame requires minimum 1 3/4” (44 mm) x 4” (102 mm) tube
• Closers to meet ADA requirements
• Standard or optional custom powder coat finish
• Optional plated finish on arm, fasteners and finish plate

Dor-o-Matic 1490 RHR/1590 LHR Push Label
4-7/8" x 1-7/16"

Doromatic part # 4270107321 or PB212 Black-No longer available
Doromatic part # 4270107320 or PB214 Gold

• For heavy weight doors
• High frequency usage
• 4 ball bearing
• Packed with wood and metal screws

Sold in boxes of 3 Hinges
Shown in brushed chrome

• For medium weight doors
• Medium frequency usage
• 2 ball bearing
• Packed with wood and metal screws

Sold in boxes of 3
Shown in brushed chrome

Shower Room Pedestal Dove Gray Color 8" x 16-1/4" Sold Individually. Heavy duty Bench Pedestals shall consist of steel tubing with 10 gauge steel flanges welded to each end. The overall height of pedestal shall be 16-1/4". Pedestals are to be finished to match the lockers in  Dove Gray color.

Provides hold-open function with templated stop/hold-open points.
Handle controls hold-open function.

Specify your current closers model number when ordering. Not all
of the LCN closers have the same shape spindle on the door closer
cylinder. This LCN Arm is known as these part numbers: 1260-3049CNS, 1460-3049CNS, 4040-3049CNS, 4110-3049CNS

Handing diagram

Heavy Duty Locker Door Knob for Two Person Locker upper doors, includes 703208 Screw. Also known as 70080, bu0113. 1" diameter x 7/8" height.