Manufacturers

Jackson 1095 Gear Package

Jackson part # 30-852

Jackson Exit Device Mounting Stud 1085/1095

The treaded part of the Jackson Mounting Stud has a 1/4-20 thread.

Jackson 1085 Body Package

Includes everything shown in picture.

Jackson part # 30-1409

Jackson 1085 and 1095 dogging pin. Includes everything shown in picture.

Jackson part # 30-1115

Jackson Exit Device 1085/1285/2086 Bottom Bolt Guide Assembly

Jackson Part # 30-320

Jackson 1085/1285/2086 Top Bolt Guide Assembly

1-1/2” deep x 1-1/16” wide x roughly 1” tall

Jackson Part # 30-934

Sargent 20/30/60/80 Connecting Arm Spring

Push Bar Return Spring

Sargent part # 68-0236

Sargent Exit Device Lever Return Spring

This spring is used on Sargent Lever Trims for there Exit Devices.

2-1/8" LONG

Sargent part # 97-0425

Sargent 60/80 Push Bar Pin Retaining Clip

used on Sargent 60 and 80 series to retain the push bar and channel axles. Use with the 68-0229 and 68-0230.

Sargent part # 01-0098

Sargent 60/80 Push Bar Pins-Short Pin

Also known as the push bar axle, this is the pin that you see on the push pad.

1-9/16" LONG

Sargent part # 68-0229

Sargent 60/80 Push Bar Pins-Long Pin

Also known as the channel axle or pin. This is the pin you see on the exit device channel, the wider of the two pins.

2-3/16" LONG

Sargent part # 68-0230

Sargent 20/30/60/80 Dogging Assembly

We only sell the dogging assembly parts as a complete set. This Dogging Assembly Kit is used on the Sargent 20, Sargent 30, Sargent 60, and Sargent 80 Series Exit Devices. This dogging assembly kit has been around since the 1980's.

Sargent part # 68-2596

Dor-o-Matic 1990 repair kit. The kit includes the following:
4 Mounting Studs
1 Hex Key 7/32"
1 Allen Key 1/8"
1 Pinion
1 Cylinder Bushing
2 Rod Bushings
1 Retractor
1 Traveller Assy

Doromatic part # 4270902091 or PBX-2

1990 parts breakdown

Doromatic 1690 1790 replacement dogging assy. The dogging assembly is used to dog the door in the open position, so people can enter the building without having to unlatch the door.  The kit ships with form threading screws for installation.

Doromatic part # KIT.1197

Dor-o-Matic 1690 Repair Parts Breakdown
Dor-o-Matic 1790 Repair Parts Breakdown
Falcon / Dor-o-Matic 2390 Parts Break Down<

Von Duprin 88 Exit Device

Von Duprin 88 rim devices for all types of single and double doors with mullion, UL listed for accident hazard installations. Field reversible, Five popular finishes, ships with 42" crossbar whichis field sizeable, Hex key dogging, 3/4"(19mm)throw latch bolt

Ships with all mounting hardware and strike.

Von Durpin 8827 surface mounted vertical rod devicesfor all types of single and double
doors, UL listed for accident hazard installations.Covers stock hollow metal doors
with 86 or 161 cutouts and fits door stiles as narrow as 3½" (90mm).

● Fully reversible
● Five popular finishes
● Field sizeable
● Hex key dogging
● 5/8"(16mm)throw latch bolt

Ships with all mounting screws and the 299, 304L and 248L-4 Strikes.

Monarch 19-V Exit Device

Hand: Field reversible.
Functions: All functions built into “EO” device.
Finishes: Powder-coated aluminum–SP28; powder-coated duranodic–SP313;
Latchbolt: Top stainless steel 3⁄4" throw. Bottom square bolt 1⁄2" throw.
Deadlocking Latchbolt: Standard.
Dogging Feature: 1⁄2 turn hex dogging standard. No threaded parts to wear out.
Stock Sizes: 3'0" and 4'0"
Doors: 13⁄4" thick, wood or metal.
Narrow Stile Doors: To 1-3⁄4" N.S. aluminum. With control trim–2-1⁄4" min. stile.
Projection: 2-1⁄2" max., 1-7⁄8" dogged.

Monarch 19-R Exit Device

Hand: Non-Handed.
Functions: All functions built into “EO” device.
Finishes: Powder-coated aluminum–SP28; powder-coated duranodic–SP313;
Latchbolt: Stainless steel, 3⁄4" throw.
Deadlocking Latchbolt: Standard.
Dogging Feature: 1⁄2 turn hex dogging standard. No threaded parts to wear out.
Stock Sizes: 3'0" and 4'0"
Doors: 1-3⁄4" thick, wood or metal. Specify thickness if other than 1-3⁄4".
Projection: 2-1⁄2" maximum; 1-7⁄8" dogged.

36" device is only 33-1/2" wide
48" device is only 43-1/2" wide

Grade 1 exit device
Device is non handed
Standard widths are 30", 36", 42" or 48"
3-3/4" minimum stile width

Replacement parts are also available

The Dor-O-Matic 2390 231CA Cylinder Kit converts your 2390 exit only to a Night Latch or Hold Back function key lock.  All the hardware is included in the package to convert your device, except for the Mortise Cylinder.  Housing measures 4-1/2" tall by 1-11/16" wide with a 1-1/8" projection.  We send the 231CA which includes the Schlage B502-191 Cam.   The 239CA is the same kit, but without the Schlage Cam.

The Monarch 25 Series Lever Trim 510L is used on the 25 Series Devices.  The Escutcheon measures 2-3/4" x 9-3/4.  The Lever is field reversible.

Jackson 2095 Exit Device

Certified ANSI 156.3 Grade 1. Made of extruded aluminum, with stainless steel and hardened steel mechanical components.

Left Hand Reverse Shown

The Von Duprin 990TP Trim is the standard Thumb Piece Trim for the 99 and 98 Series devices.  The plate is constructed of Bronze or Stainless Steel and then plated to the desired finish.  The plate measures 3" wide by 14-3/16" tall, and includes the mounting screws.  The stanchions coming off the back of the plate line up with the center case mounting screws.  The key cylinder locks and unlocks the thumb piece.  The Rim Cylinder shown in the picture is not included.

Von Duprin Part # 990TP-R&V

Cylinder not included.

The Von Duprin 990NL Trim is the standard NIght Latch Trim for the 99 and 98 Series devices.  The plate is constructed of Bronze or Stainless Steel and then plated to the desired finish.  The plate measures 3" wide by 14-3/16" tall, and includes the mounting screws.  The stanchions coming off the back of the plate line up with the center case mounting screws.  The Rim Cylinder shown in the picture is not included.

Von Duprin Part # 990NL-R&V

The Von Duprin 996L Lever Trim replaces the 992L, and 994L and is the latest generation of the 99 Lever Trim.

The escutcheon plate measures 2-3/4" wide by 10-3/4" high and projects out 27/32". The handle projection is 2-7/8". This lever handle is handed, but is field reversible. Key lock and unlocks lever.

Von Duprin 990K Knob Trim

Plate measures 3" wide by 14-3/16" long.

Von Duprin Part # 990K-R&V

The Von Duprin 990DT Trim is the standard Dummy Trim for the 99 and 98 Series devices.  The plate is constructed of Bronze or Stainless Steel and then plated to the desired finish.  The plate measures 3" wide by 14-3/16" tall, and includes the mounting screws.  The stanchions coming off the back of the plate line up with the center case mounting screws.

Von Duprin Part # 990DT-R&V

Cal-Royal 9000 Series Lever Trim HDESC is for use on the 9800 and 9800 Exit Devices. The Trim has a clutch mechanism to prevent breaking and two heavy duty springs to prevent sagging. Escutcheon measures 2-5/8 inches wide by 10-5/8 inches long.  The lever projects out 2-7/8 inches. Key locks or unlocks lever.

• For 1-3/4" (44mm) doors standard
• Through-bolted with 3 mortise nuts
• Pulls project 1-1/2" (38mm) from door face
• GTB Design trim will cover a 161 cutout

Cal-Royal 9000 Series NESC Lever Trim features hardened steel tailpiece and heavy duty spring to prevent sagging. Standard 6-Pin Schlage C mortise cylinder included. Rigid entrance, key locks or unlocks lever.

The Cal-Royal NARL9800 is a time tested heavy duty Alarmed exit device.  Alarm works with a 9 volt battery.

• For 1-3/4" (44mm) doors standard
• Through-bolted with 3 mortise nuts
• Pulls project 1-1/2" (38mm) from door face
• GTB Design trim will cover a 161 cutout

Sargent 3828 Series Exit Device

The 3828 is a rugged exit device in a rim design. The 3828 Non Configured Rim Exit Device has 7 functions, 4 available trims and is easy to mix and match the device and trim. Aluminum finish only.