Mills Toilet Partition

chrome plated top and bottom hinge set for 1-1/4" round edge pilaster, includes everything you see in the picture. known as hdwt-z01 through Mills Partitions.

Selling Mills Door Cam for over 35 years. Your One Stop shop for all Bathroom Hardware and Partitions.

Mills Partitions ADA Concealed Slide Bolt Latch Concealed Chrome Plated

Covers are polished chrome plated. Latch cover plates are 1-3/4" wide by 1-3/8" high. The latch switch is 1-15/32" wide. The latch bolt is 3/8" diameter. The spacing between the cover and the latch 1-1-32". This is a one of a kind latch. Also known as a Bathroom Stall Concealed Latch. Manufacture part # 4230, HDWT T290.

Chrome Plated Toilet Partition Keeper Bumper Inswing Flat Stop

Chrome plated Zamac die casting. The strike and keeper measure 2-1/2" tall by 2-9/16" deep and is 1/8" thick. The stop projects out 3/4" and has a rubber insert. The mounting holes are 1-19/32" on center. Also known as a Bathroom Stall Strike and Keeper - Inswing Flat. Flat backed for wall mounting. Manufacture part # 5140

Shipped with mounting screws.

Mills Toilet Partitions Keeper Bumper For 1-1/4" Inswing Square Edge Pilaster Or Post

Zamac die casting that is polished chrome plated. The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. The latch bolt slot is 1-9/16" high by 5/16" deep. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for inswinging doors. Also known as a Bathroom Stall Strike and Keeper-Inswing 1-1/4". Manufacture part # 5110

Shipped with mounting screws.

Surface Mounted Slide Bolt Latch 3/8" Bar To Door Clearance

Zamac die cast construction, polished chrome finish. Latch base is 4" high with 2-3/4" hole spacing. Latch bolt is 3-3/4" long by 3/4" wide by 3/16" thick. The latch bolt clearance is 3/8" from the back of the base to the under side of the latch bolt and projects out 15/16". The latch projects out 1-9/16" from the face of the door when installed. Also known as a Bathroom Stall Surface Mounted Slide Bolt Latch and Toilet Partition Locks. Manufacture part # 5030.

Shipped with mounting screws.

Mills Keeper Bumper 1-5/8" Between Screws, Surface Mount For Round Edge Posts

Polished chrome plated Zamac die casting. The strike and keeper measure 2-1/4" high by 29/32" wide and 15/16" deep. The hole spacing is 1-5/8" on center. Also known on Bathroom Stall Strike and Keeper Inswing/Outswing 1-1/4". Manufacture part # 5550.

Shipped with mounting screws.

Mills Toilet Partition Keeper Bumper For Concealed Latches 1-1/4" Round Edge Post

Polished chrome plate Zamac die casting construction. Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5590.

Shipped with mounting screws.

Lathern or Liquid Dispenser
8" w x 5" h x 3 d"
40 oz Bulk Fill
Stainless Steel

Single Roll
Deluxe Chrome
Die Cast
tension spring controls tissue flow for 4-1/2" wide rolls

Double Roll
Deluxe Chrome
Die Cast
tension spring controls tissue flow for 4-1/2" wide rolls

replacement eye piece. also known as P15-405.

Partition Slide Latch, Cast Stainless Steel With Hole Spacing 1-3/4" X 1-1/2"

Cast stainless steel construction. The latch base is 2-31/32" wide by 1-15/16" high and projects 1-1/8" high. The hole spacing is 1-3/4" wide by 1-1/2" high. The four mounting holes have a diameter of 1/4". The Slide Latch base is 1/4" thick. The latch bolt is 7/8" wide by 3-7/16" long. This toilet stall latch is used on Accurate and Mills Partitions. Also known as a Bathroom Stall Slide Latch. Manufacture part # 6983.

Shipped with mounting screws.

 

Coat Hook & Bumper 3-1/2" Projection x 2-3/4" High Chrome Plated

Chrome plated Zamac construction. Coat hook base is 1-1/2" wide by 2-3/4" high, with screw spacing of 7/8" at the top. Hook projects out 1". Bumper projects out 3-1/2" with a rubber insert. Also known as a Bathroom Stall Coat Hook and Bumper. Manufacture part # 4260.

Same as 9OT285, 9HA426