Search results for: 'roll 7000 100 high'

Non-fading superior aging properties make this oil, grease, chemical and stain resistant matting a popular item. Non-combustible; tear, cut, impact and ozone resistant; high tensile strength and elongation properties; single piece rolls. Use inside or outside. Round ribbed corrugations run lengthwise, easily cleaned with soap and water.

GREASE AND OIL RESISTANT — NO FABRIC

Pricing below is per linear feet, Black Only, Size is the Width

The 893 Hat And Coat Strip are available in 24", 36", 48" and 56". These are constructed of 18 gauge type 304 stainless steel, the hooks are constructed of 14 gauge stainless steel, both are finished to a #4 satin brushed finish.  The strip is 4" high by length and projects out 1/2".  The hooks are 1" wide by 6-11/16" high and project out 2-1/8", and have radiused ends to prevent injury. Manufactures part number is 1307 by American Specialties.

24" unit has 3 hooks.
36" unit has 4 hooks
48" unit has 5 hooks
56" unit has 6 hooks

Toilet partition round edge pilaster shoe, stamped stainless steel construction. Pilaster Shoe measures 2" to 24" wide by -1-1/4" thick by 3" high. This size pilaster post shoes are split on one end for easy installation. Also known as a Bathroom Stall Pilaster Post Shoe Round Edge. Used for the base of the support system with pilaster mounting.

Toilet partition square edge pilaster shoe split, stamped stainless steel construction. Pilaster Shoe measures 2" to 24" wide by -1-1/4" thick by 3" high. This size pilaster post shoe is split on one end for easy installation. Also known as a bathroom stall pilaster post shoe square edge. Used for the base of the support system with floor mounted pilaster.

Toilet partition square edge pilaster shoe, stamped stainless steel construction. Pilaster Shoe measures 2" to 24" wide by -1" thick by 3" high. This size pilaster post shoe is not split on either end. Also known as a bathroom stall pilaster post shoe square edge. Used for the base of the support system with pilaster mounting.

Toilet partition square edge pilaster shoe, stamped stainless steel construction. Pilaster Shoe measures 2" to 24" wide by -3/4" thick by 3" high. This size pilaster post shoe is not split on either end. Also known as a bathroom stall pilaster post shoe square edge. Used for the base of the support system with pilaster mounting.

405CR Vinyl Stair Tread Risers

Plain color cove risers match Koroseal vinyl stair treads; or use a contrasting riser with vinyl or rubber treads; easily trimmed in height and length; savings in installation are substantial; cove risers are same sizes as stair treads.

SPECIFICATIONS:

Furnish and install No 405CR Koroseal vinyl coved stair riser; 1/8” thick, 7” high with 5/8” toe; ribbed back. Select standard length of 18”, 24”, 30”, 36”, 42”, 48”, 54”, 60”, 72”, 84” or 96”. Select standard solid color of Brown, Sand, Gray or Black.

GSA11 ALUMINUM STAIR TREADS

Diamond hard aluminum oxide abrasives combined with "space-age" polymeric binders are bonded to a heat treated high strength aluminum square nose stair tread. Treads are available GSA75-7-1/2", GSA9-9" or GSA11-11" deep; in one or two contrasting colors per tread. Flat pieces, GSA35-3-1/2" or GSA55 5-1/2" deep, can be used for ramps and other non-step applications or as a filler behind the 7-1/2" treads. Select one color for front insert and the same or a different color for back insert from seven standard abrasive colors of black, brown, blue, gray, green, red or yellow. Maximum lenght is 10 foot. Nose drops 1-1/16".

Install outdoors or indoors on concrete, wood, treated lumber, slate or marble steps. Use for motels, schools, hotels, apartments, condos, hospitals, churches, cruise ships, amusement parks, etc. Offers anti-slip safety surface - protects new steps - renovate slippery, worn steps.

Purchase the 11" model here.

Diamond hard aluminum oxide abrasives combined with "space-age" polymeric binders are bonded to a heat treated high strength aluminum square nose stair tread. Treads are available GSA75-7-1/2", GSA9-9" or GSA11-11" deep; in one or two contrasting colors per tread. Flat pieces, GSA35-3-1/2" or GSA55 5-1/2" deep, can be used for ramps and other non-step applications or as a filler behind the 7-1/2" treads. Select one color for front insert and the same or a different color for back insert from seven standard abrasive colors of black, brown, blue, gray, green, red or yellow. Maximum lenght is 10 foot. Nose drops 1-1/16".

Install outdoors or indoors on concrete, wood, treated lumber, slate or marble steps. Use for motels, schools, hotels, apartments, condos, hospitals, churches, cruise ships, amusement parks, etc. Offers anti-slip safety surface - protects new steps - renovate slippery, worn steps.

Purchase the 9" model here.

Diamond hard aluminum oxide abrasives combined with "space-age" polymeric binders are bonded to a heat treated high strength aluminum square nose stair tread. Treads are available GSA75-7-1/2", GSA9-9" or GSA11-11" deep; in one or two contrasting colors per tread. Flat pieces, GSA35-3-1/2" or GSA55 5-1/2" deep, can be used for ramps and other non-step applications or as a filler behind the 7-1/2" treads. Select one color for front insert and the same or a different color for back insert from seven standard abrasive colors of black, brown, blue, gray, green, red or yellow. Maximum lenght is 10 foot. Nose drops 1-1/16".

Install outdoors or indoors on concrete, wood, treated lumber, slate or marble steps. Use for motels, schools, hotels, apartments, condos, hospitals, churches, cruise ships, amusement parks, etc. Offers anti-slip safety surface - protects new steps - renovate slippery, worn steps.

Purchase the 7-1/2" model here.

The Emco R1 Wall Rack system is perfect for hotels, restaurants, churches and schools. It is easy to install and built to last.  They project 12-1/8" from the wall and the support brackets are 12" high and 1-7/16" wide.  The slats measure 3/4" by 1" rectangle with a wall thickness of .062" and are constructed of extruded aluminum and have plastic end closures.  The mounting brackets are made of cast aluminum that is powder coated black.  For the slats we have the option of Silver Anodized Aluminum or Bronze Acrylic Coated Aluminum.  We show the more popular sizes on the website, but we can get these up to 50' long.  Manufacturer will use slip joints so the rack can ship UPS/FEDEX.  Hangers are not included.

The Emco W Wall Mounted Hook Strip is an ideal complement under any shelf system. May also be used by itself. Comes with double pronged poly-carbonate hooks. The wall bracket measure 6-1/4" and are 1-7/16" wide, and are constructed of cast aluminum that is then powder coated black.  The bar (slat) that the hooks are mounted on is 3/4" high by 1" deep.  The slat is available in dark bronze or aluminum.  The poly-carbonate hooks measure 3" wide by 2-3/4" high and project out 1-1/2".  The hooks are available in Black, Blue, Brown, Gray, Green, Orange, Purple, Red, Yellow, or Assorted Color Hooks.  The number of brackets and hooks is determined by the length of the hook strip.

24" racks have 3 hooks/2 brackets
36" racks have 4 hooks/2 brackets
48" racks have 6 hooks/3 brackets
60" racks have 8 hooks/3 brackets
72" racks have 10 hooks/3 brackets

Racks can be made any size up to 50'. Manufacturer will use slip joints so the rack can ship UPS/FEDEX.