Search results for: 'spring for inside strip'
-
Hat & Coat Strip
The 893 Hat And Coat Strip are available in 24", 36", 48" and 56". These are constructed of 18 gauge type 304 stainless steel, the hooks are constructed of 14 gauge stainless steel, both are finished to a #4 satin brushed finish. The strip is 4" high by length and projects out 1/2". The hooks are 1" wide by 6-11/16" high and project out 2-1/8", and have radiused ends to prevent injury. Manufactures part number is 1307 by American Specialties.
24" unit has 3 hooks.
36" unit has 4 hooks
48" unit has 5 hooks
56" unit has 6 hooksKJ893 -
Emco W Wall Mounted Hook Strip
The Emco W Wall Mounted Hook Strip is an ideal complement under any shelf system. May also be used by itself. Comes with double pronged poly-carbonate hooks. The wall bracket measure 6-1/4" and are 1-7/16" wide, and are constructed of cast aluminum that is then powder coated black. The bar (slat) that the hooks are mounted on is 3/4" high by 1" deep. The slat is available in dark bronze or aluminum. The poly-carbonate hooks measure 3" wide by 2-3/4" high and project out 1-1/2". The hooks are available in Black, Blue, Brown, Gray, Green, Orange, Purple, Red, Yellow, or Assorted Color Hooks. The number of brackets and hooks is determined by the length of the hook strip.
24" racks have 3 hooks/2 brackets
36" racks have 4 hooks/2 brackets
48" racks have 6 hooks/3 brackets
60" racks have 8 hooks/3 brackets
72" racks have 10 hooks/3 bracketsRacks can be made any size up to 50'. Manufacturer will use slip joints so the rack can ship UPS/FEDEX.
EM-W-xx -
Aluminum Nosing 2 inch with Grit Surface
This 2-1/2" deep nosing is made from the same material as our Grit-Surface Aluminum Treads. The front edge is 1-3/4" deep (inside nose dimension is 1-1/4"). The nose has a 1-3/4" wide abrasive finish with a 3/4" tapered aluminum back edge. Both the nose and tapered edge have a 1/4" wide reflective yellow safety tape strip for additional safety. The nosing is available in abrasive colors of Black, Brown, Blue, Gray, Green, Red or Yellow. Nosing is available solid (for glue-down applications) or with countersunk holes (for screw-down applications) every 12". Nose drops 1-1/16".
SPECIFICATIONS:
Furnish and install Musson Grit-Surface Aluminum Nosings, 3/16" thick X 2-1/2" deep; cut lengths up to 10 foot long. Tread surface shall have aluminum oxide abrasives permanently bonded to a heat treated aluminum nosing with 1/4" wide reflective yellow safety strip on both the top surface (between the grit surface and aluminum) and the nose. Grit surface shall be in one of the following standard colors: Black, Brown, Blue, Gray, Green, Red or Yellow. Nosings can be supplied with two countersunk holes every 12" for screw down installation or without holes for installation with our #400 Neoprene Contact Cement.
Custom sizes are available up to 10' long
GSA2N- -
Easy Sweep Rib Runner Mat
Non-fading superior aging properties make this oil, grease, chemical and stain resistant matting a popular item. Non-combustible; tear, cut, impact and ozone resistant; high tensile strength and elongation properties; single piece rolls. Use inside or outside. Round ribbed corrugations run lengthwise, easily cleaned with soap and water.
GREASE AND OIL RESISTANT — NO FABRIC
Pricing below is per linear feet, Black Only, Size is the Width
MXXX -
ADA Grab bars
The Handicap Grab Bar is fabricated of #18 gauge stainless steel with a #4 satin finish. They are available in 1 1/4” and 1-1/2” outside diameter. All bars maintain a constant 1 1/2” offset, which is the distance between the inside of the bar and the mounting surface. The mounting flanges have a 3” diameter. We offer two types of mounting, exposed screw mounting and snap on flange concealed. When properly installed they will easily support up to 250 pounds. The recommended height for mounting these grab bars is 33 to 36” above the finished floor, but heights vary depending on local codes. The overall length of a 12" grab bar is 15" due to the 3" diameter flanges. Due to the various materials that these are mounted on, screws are not included.
K74
