Search results for: 'rivet brush partit'

Pull Plate 5020

The plate is constructed of .050" wrought metal, in either solid aluminum, brass or stainless steel, with Door Pull GHE20 -8" center. Handles come with thru bolts, finish washers and the plates come with sheet metal screws that fit the countersunk holes.

Finishes

Wall Mounted Door Stop WS33

• Constructed in a durable cast brass and then brushed chrome plated.
• Replaceable rubber bumper with offset shoulder screws into cavity on body to prevent loss or theft.
• Sloping design discourages vandalism

WS33 is furnished with wood screws for drywall mounting.

The offset door pull 44 is 5 inches by 12 inches.  It offers a 2 inch clearance with a 2-1/8 inch projection.  The mounting holes are 10 inches on centers.  The base block is 1 inch by 12 inches.

The Heavy Duty Cal Royal CRCODE101 is for use on the 7700 and 9800 Rim and Surface Vertical Rods. This lock features Single Code with up to 8000 code combinations, weather resistant, non handed, and code can be changed without removing the lock. Comes in Brushed Chrome finish only.

Installation and Programming Instructions

The Cal-Royal 9800 Rim Device is a grade 1 Heavy Duty Exit Device.   The 9800 has the same template as the 8800 and 9800 with escutcheon lever trim. The 36 inch device will be 32 inches wide and can be cut down an additional 2" to fit doors as narrow as 30 inches.  The 48 inch will be 44 inches wide and can be cut down to fit doors 36 inches wide. The device is non handed, meaning it will work on a left hand reverse or right hand reverse door. Strike and mounting screws are included.

Door Pull 15

This door handle features 7-1/2" centers on the mounting screws. With 2" diameter bases. The Grip has a 2-1/4" projection with a 1-5/8" clearance. Also known as a Door Handle or Door Grip. This handle ships with thru bolts and finish washers.

Finishes

Hadrian Headrail End Plug for Metal and Stainless Steel Partitions. This is used to close off the end of the partition headrail at the top of your partitions. This goes over the 1"x1-5/8"ht outside edge of headrail opening. Known as part number 607220 and used only with Hadrian Partition Company.

Two Hole 1-1/4" Window Handle 5/16" Lockup With Ring Pull

This window handle features a 1-1/4" hole spacing, a 5/16" lock up dimension and a ring pull for elevated windows. This handle is cast white bronze construction with a brushed nickel finish

Two Hole 1-3/8" Window Handle 5/16" Lockup With Ring Pull

This window handle features a 1-3/8" hole spacing, a 5/16" lock up dimension and a ring pull for elevated windows. This handle is cast white bronze construction with a brushed nickel finish.

Right Hand Shown

The Von Duprin 996L Lever Trim replaces the 992L, and 994L and is the latest generation of the 99 Lever Trim.

The escutcheon plate measures 2-3/4" wide by 10-3/4" high and projects out 27/32". The handle projection is 2-7/8". This lever handle is handed, but is field reversible. Key lock and unlocks lever.

Ives Sweep Lock07

The Ives Sweep Lock are made of solid brass and plated to your desired finish.   The base is 15/16" x 2-9/16", and the Strike is 5/8" x 2-9/16".  The center to center distance on the screws 1-15/16".

Ives Part # 07

Monarch 25-V Series Center Case Cover Kit

Replacement cover for the Monarch Falcon 25-V Exit Device.   Kit includes cover and the mounting screws.

Falcon Part # 650257

Ives Wall Bumper Heavy Duty WS401CCV

Features:

• Special retainer cup makes rubber tamper resistant.
• Constructed in heavy-duty cast brass or aluminum base.
• The WS401CCV unit is designed with a concave rubber bumper which avoids damage to ocks with projecting buttons, packed with wood screw and plastic anchor.

2-1/2" diameter with a 1" projection

Two Hole 1-1/2" Window Handle

This window handle has a 1-1/2" hole spacing with a 5/16" lock up dimension. The handle also features a ring pull for elevated windows. Cast white bronze with a brushed nickel finish.

Right Hand Shown

Sargent Exit Device 90 Series End Plug 97-0008

Sargent 97-0008 End Plug and 01-001 End Plug Screw.  Fits the 90 series cross bar panic devices.

Cal Royal 7000 Lever Trim

Two Hole 1-3/8" Window Handle 5/16 Lock Up

This window handle features a 1-3/8" hole spacing wth a 5/16" lock up. The handle as a cast white bronze construction with a brushed nickel finish

Door Pull 16

This door handle has an overall length of 7-1/2". The base diameters are 2" with three holes each. The handle projects out 2-1/4" and has a clearance of 1-1/2". Also known as a Door Grip or Door Handle. This handle ships with 6 wood/sheet metal screws.

Finishes

Handicap Door Pull 18

With this handle you are able to get a closed fist behind the pull, which makes it a great ADA Door Pull. Shipped with screws. Also known as a Handicap Grip, ADA Door Pull or Handle.

Finishes

Door Pull 17

This door handle has an overall length of 10". The base diameters are 2" with three holes each. The handle projects out 2-1/4" and has a clearance of 1-1/2". Also known as a Door Grip or Door Handle. This handle ships with 6 wood/sheet metal screws.

Finishes

The Ives Wall Bumper Stop WS407-CCV our economically price wall bumper.  The metal ring is a wrought stainless steel, otherwise known as stamping.  It features a concealed tamper-proof mounting, and is shipped pre-assembled to the back plate is reduce installation time.   Installation is easy, just insert the screw driver through the pin hole in the rubber and tighten.  The bumper is 2-1/2" in diameter and projects out 1".

Ives Floor Mounted Door Holder FS41

Features:
• Automatic door holders ideal for heavy-traffic situations that require a simple,
fool-proof, Hold-Open device.
• Forged from brass.
• Unit is activated automatically when door is opened. A firm pull on door releases
the mechanism.
• Strikes accommodate different door to floor clearances.
• Model numbers are determined by strike/door-to-floor clearances.
• Holder position on door is adjustable.

Door to Floor Clearance 9/16" to 1-1/16"
Holder Dimensions 3" Wide x 3-11/16" High

Von Duprin 98 rim exit devices for all types of single and double doors with mullion, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1. The Von Duprin 98 device has a smooth mechanism case and the Von Duprin 99 device has a grooved case. The rim device is non-handed.

Ships with all the mounting screws and the 299 Strike.

Pull Plate 5810

7/32" thick forged plate made of solid aluminum, brass or stainless steel depending on the finish. The Door Pull GHE10, handles come with thru bolts and finish washers. The plate has counter sunk holes and sheet metal screws for mounting. 3-1/2 x 15 inch Plate only.

Finishes

Fabricated from B & S 16 ga. (.050). Standard lengths are 36", 42" and 48". Custom capabilities include variations of all of the above parts including frame protectors and vertical rod protectors.

2" x 2" x 48"

Screws included for mounting

Custom sizes are available!

Please allow 1 week shipping time

Finishes

Wall Mounted Door Stop WS443

Features:

• Constructed in brass.
• Ideal for interior or exterior use.
• Non-marring rubber tip.
• Packed with expansion shield and lead shield.

Diameter 2-1/4"
Projection 3-11/16"

The Burns 618 Locking Pocket Door Latch is 2-3/4 inches tall by 2-1/2 inches deep. The mortise dimensions are 2-5/16 inches tall by 1-7/8 inch deep. Base metal is Brass or Aluminum depending on the finish.

Monarch 24-V Series Center Case Cover Kit

Replacement cover for the Monarch Falcon 24-V Narrow Stile Exit Device.   Kit includes cover and the mounting screws.

Falcon Part # 650251

Von Duprin 9827/9927 surface mounted vertical rod device for all types of single or double doors, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1. Covers stock hollow metal doors with 86 or 161 cutouts. The Von Duprin 9827 device has a smooth mechanism case and the Von Duprin 9927 device has a grooved case. The surface vertical rod device is non-handed.

Cal Royal 7760 Surface Vertical Rod Exit Device

For use in institutions, schools, universities, commercial buildings where heavy duty reliable operation is a requirement. ANSI A156.3, Grade 1 heavy duty exit device in surface vertical rod and rim designs. Rail assemblies are heavy duty extruded aluminum body with stainless steel push pad and end caps are made of brass, bronze or stainless steel. Rail travels in direction of the door swing. Trims are thru bolted for additional security. Conforms & Meets ADA Regulations. UL Listed for Panic and ULC10C, UBC 7-2-1777 codes. UL Listed for Fire Exit Hardware.

Templating matches the Von Dupin 99 and 98

Door Pull 21

This handle has a cross section dimension of 1/2" x 1" and is made of half round (underside is round) stock. The handle projects out 2-1/8" with a clearance of 1-5/8". This handle is available in 6" and 8" center to center mounting holes, but can be made in different Center to Center dimensions. This product is also known as a Door Handle or Door Grip. The handle ships with thru bolts and matching finish washers.

Finishes

Von Duprin 33/3547A/49A Center Case Cover Kit

Replacement Von Duprin 33/3547A/49A Concealed Vertical Rod Center Case Cover Kit.  Screws come with the new cover.

Von Duprin Part # 050485

Keeper Bumper- Outswing For 1-1/4" Sq Edge Chrome Plated Construction

Used on many toilet partition manufacturers partitions, known as 40-8512354.

Project In Window Handle 1-3/8"

This window handle features a 1-3/8" hole spacing with a 7/16" lock up. The mounting holes are located on the back of the handle and are tapped for a standard thread screw. Cast white bronze, with brushed nickel finish.

Roller Bumper Straight Arm 4" RB471

Features:

• Constructed in heavy-duty cast brass.
• RB471 is ideal for use in situations where doors meet each

other at approximate right angles (back to back).