Search results for: 'covers latch that tip acrylic solid'

Aluminum Store Front Door Flush Bolt FB-1202

15/16" x 4-1/4" radius face, 5-7/32" hole spacing, 1/8" offset, 5/8" throw, 12" rod length, with a square nylon tip with beveled corners fits in a 1/2" square hole.

Concealed Partition Latch Keeper Bumper Inswing Cast Stainless Steel

Stainless steel casting. The strike and keeper is 1-1/4" high by 2-1/2" deep by 1/8" thick. The stop is 1/2" deep by 1-1/4 wide with a rubber insert. The slots are 1/4" deep. Also known as a Bathroom Stall Strike and Keeper Inswing Flat. Manufacture part # 5653.

Shipped with mounting screws.

The Falcon/Monarch Fire Rated Top Latch is used on the F-19-V, F-24-V, F-25-V, F-18-V and F-XX-V Surface Vertical Rods.  The new number from Falcon is 650375, the old Monarch Number was F588.  This latch is used on the above devices that are Fire Rated, meaning you can not dog these device in the Unlock Position.  If your device has the ability to be dogged open, then use the G588 Non Fire Rated Version

Pull Plate 5026

The plate is a solid .050" wought plate of solid aluminum, brass or stainless steel depending on the finish. The Door Pull GHE26 has 8" centers and is constructed of solid aluminum, brass or stainless steel, and is 1" in diameter, handles come with thru bolts. The plate come predrilled with counter sunk holes and sheet metal screws in matching finiish.

Finishes

FEATURES

• Please note the factory will only sell in quantities of 10.
• Supervisory key control
• Ergonomic dial with grip ring and non-slip coating
• Fully retracting automatic spring latch with standard 5/16” bolt
• Automatic locking
• 7 pre-set combinations for extended usage
• 3-digit dialing combination with 5-pin tumbler key plug
• Patent pending button guard to protect lock function from overstuffed lockers
• Nut channels for easy installation
• All Built-in Combo Locks have a 10 year warranty from time of shipment
• 72 hour shipping available

APPLICATIONS

• Model 1954 is for use with locker door hinged on right; similar in operation to Master Lock 1654
• Fits all standard single point or box lockers

The Command Access MLRK1-VD22 is a motorized electric latch retraction with REX for the Von Duprin 22.  This motor is 24 to 28 volts and has a Standard : 900 mA (Avg Current Peak); 215 mA (Avg Current Hold). This unit requires 18 ga wire.  And ships with (1) Motor Mount with MM5; (2) 40002 - 8/32 x 1/4 inch Phillips Head Screw; (1) 50030 8/Lead with vd Connector; (1) 50944 Molex Pigtail; (1) 40144 Dogging Hole Cap; (1) 50991 Fire Rated Drilling Template; (1) Replacement Dogging Tail Piece.

The MLRK1-VD22 is a cost-effective and straightforward way to upgrade your Von Duprin 22 series device to motor-driven latch retraction in the field. UL Listed + 3 Year Warranty

The Command Access MLRK1-JAC12 Motorized Latch Retraction Kit With REX is for use on the Jackson CRL 1285 and 1295 Series Exit Devices. The unit is 24 volt with Standard : 900 mA (Avg Current Peak); 200 mA (Avg Current Hold). The unit requires 18 ga wires. The package includes:  1) Motor Mount with MM5; (1) 50944 Molex Pigtail; (1) 50030 6 Feet Lead with VD Connector; (2) 40124 10-24 x 3/8inch Phillips Screws (Silver); (2) 40125 10-24 x 3/8inch Phillips Screws (Black).

The MLRK1-JAC12 is a cost-effective and straightforward way to upgrade your Jackson 12, Kawneer 16/17 and PD16 series device to motor-driven latch retraction in the field. UL Listed + 3 Year Warranty.

Concealed Partition Latch Keeper Bumper 1-1/4" Post Round Edge Cast Stainless Steel

Cast stainless steel construction. Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5513.

Shipped with mounting screws.

7/16" X 3/4" SLOT

Sanymetal Partitions Keeper Bumper And Strike For Concealed Latches Inswing/Outswing 1-1/4"

Zamac die cast and polished chrome plate construction. Keeper is 1-1/4" tall by 2-3/8" wide by 1-3/4" deep. The strike is a1/2" thick and the slot is 7/16" deep. The opening to mount it on the pilaster or post is 1-1/4" by 1-1/4" This Strike and Keeper are for square post or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5960

Shipped with screws for mounting.

International 58L Escutcheon Trim for the 5000 Series Devices

Non-handed, easily install with exit device Escutcheon plate measures 8-1/16" tall by 2-5/8" wide by 29/32" thick. We offer 3 functions, Classroom, Passage and Storeroom.

Classroom - cylinder (not included) locks and unlocks lever handle-Most Popular
Passage - no cylinder hole, lever always active
Night Latch (Storeroom) - cylinder (not included) unlocks lever, but lever is always locked when key is removed.

For use on the Doromatic 1790 exit devices only. It will not work on the other Doromatic exit devices.  This lever trim is now field reversible, the handing can be changed in the field.

FEATURES

• Please note the factory will only sell in quantities of 10.
• Large, all-steel ADA Compliant User Paddle Key for ease of access
• Ergonomic dial with grip ring and non-slip coating
• Nut channels for easy installation
• Fully retracting automatic spring latch with standard 5/16” bolt
• 7 pre-set combinations for extended usage
• Supervisory key control
• Includes 2 User Keys
• Nut channels for easy installation
• Automatic locking
• 3-digit dialing combination with 5-pin tumbler key plug
• All Built-in Combo Locks have a 10 year warranty from time of shipment
• 72 hour shipping available
  

APPLICATIONS

• Fits all standard single point or box lockers
• Model 1954ADA is for use with locker door hinged on right

Corbin Russwin Door Closer H.D. Hold Open Arm

Recommended for high-use, high-abuse environments, Tamper-resistant, solid forged steel riveted arm, Mounted on push side, and Not available in plated finishes.

Corbin Russwin part # 689F04

Corbin Russwin Door Closer H.D. Parallel Arm

Recommended for high-use, high-abuse environments, Tamper-resistant, solid forged steel riveted arm, Mounted on push side, and Not available in plated finishes

Corbin Russwin part # 689F02

26" Full Dome 360 Degree Mirror. 26" diameter, full dome 360 degrees. Covers up to 400 square feet. 

26" Quarter Dome 90 Degree Mirror, 1/4 Dome, 26" diameter and Covers up to 75 square feet.

Swivel spindle
9/32" square x 4-3/4" long
20 tpi, one 3/8" solid square

Toilet Partition Surface Mounted Ada Slide Bolt Latch And Keeper Stainless Steel

Stamped stainless steel construction. Slide lock measures 4-3/16" long by 1-1/8" tall by 15/32" thick. The mounting plate has mounting screws 1-1/4" on center and is 2-15/32" long. The lock projects out 1-3/16" from the face of the door. The keeper is 1-1/2" wide by 1-1/8" tall by 3/32" thick. Commonly known as a Bathroom Stall Surface Mounted ADA Slide Lock and Toilet Partition Locks. Manufacturer part # 6049, 1002927.

Shipped with mounting screws. For 1" thick doors.

Von Duprin 22 Exit Device Only

Von Duprin 22 rim exit device for all types of single and double doors with mullion, UL listed for Panic Exit Hardware. Devices are ANSI A156.3, 2001, Grade 1. Covers stock hollow metal doors with 161* cutouts. Fits door stiles as narrow as 3 13/16"

Ships with all mounting screws and the 299 strike.

20 tpi
4-3/4" long
1 solid center
3 pin holes one side

Polished Brass Kick Plate

Solid brass kick plate, polished to mirror finish.  We can no longer get the solid brass plates, the lifetime polished brass will be shipped in its place.

Custom sizes available starting around $0.40 per square inch depending quantity

Please allow 1 week shipping time

Kick Plates come pre drilled with screws.

I would highly recommend the Lifetime Brass if these plates are going to be mounted outside. Solid brass is soft, and tends to dent easily and the clear coat can be compromised. The Lifetime Brass plates do not require a clear and will last a lot, lot longer!

Truth Entrygard Flip and Fold Handle 12905

Can be used on all Truth Entrygard Operators. Replaces the orignal handle and cover with a folding handle that fits flush into the cover.

11/32" spline

International 89L Escutcheon Trim

Clutched lever trim for use with the 8000 Series International Door Closer Exit Devices. Escutcheon measures 8-27/32" high by 2-15/16" wide by 15/16" thick. Trim is non handed and easily converted in the field. We offer 3 functions, Classroom, Passage and Storeroom.

Classroom - cylinder (not included) locks and unlocks lever handle
Passage - no cylinder hole, lever always active
Storeroom (Night Latch) - cylinder (not included) unlocks lever, but lever is always locked when key is removed.

Swivel spindle
9/32" square, 16 tpi
4-3/4" long, w/ two solid centers

Wall Mounted Holder/Stop WS445

• Constructed in cast of brass or aluminum.
• Unit functions as a stop but serves as a Hold-Open device when hook is manually engaged in strike.
• Unit requires manual disengagement to release Hold-Open.
• Replaceable resilient, non-marring rubber tip.

WS445 is packed with expansion shield and lead shield for masonry type mounting.

Concealed Partition Latch Keeper Bumper Outswing 1-1/4" Square Edge Cast Stainless Steel

Cast stainless steel construction. Keeper is 1-1/4" tall by 2-3/8" wide by 1-13/16" deep. The strike is 1/2" thick with rubber insert. The opening to mount it on the square edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5973.

Shipped with screws for mounting.

Bobrick B-7120/B-7128 series hand dryers are a durable 22 gauge type 304 satin finish stainless steel cover option or a zinc plated steel with white epoxy cover with black plastic trim. Choices are 115 volt or 230 volt.

Concealed Partition Latch Keeper Bumper Inswing 1-1/4" Round Edge Cast Stainless Steel

Cast stainless steel construction. Keeper is 1-1/4" tall by 2-3/8" wide by 2-9/16" deep. The strike is a17/32" thick and the slot is 1/4" deep. The opening to mount it on the round edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing 1-1/4". Manufacture part # 5583.

Shipped with screws for mounting.

1" Diameter Solid Aluminum Round

Anodized Finishes, Aluminum or Dark Brown

Cross bar has a 33-1/16" Center to Center screw spacing

Mounting Hardware Included

Bobrick Toilet Partitions Inswing Keeper Bumper For Throw Latch For 1" Sq Edge Post

Polished chrome plated Zamac construction. The strike and keeper is 2-1/2" tall by 1-15/16" wide. The mounting holes are 1-1/2" on center. The stop is 2-1/2" tall by 13/16" projection with a rubber insert. The two slots are 5/16" deep by 13/16" high. Also known as Bathroom Stall Strike and Keeper Inswing 1". Manufacture part # 5820.

Shipped with mounting screws.

Floor Mounted Door Stop FS444

This door stop has been around a long time. We have been selling it for the past 35 years, and it is one of our best sellers year in and year out.

Features: Ideal for interior or exterior use. Cast brass construction. Accommodates door undercut up to 2-1/2". Non-marring rubber tip. Packed with expansion shield and lead shield. This Floor Mounted Door Stop is 3" high, and the base has a 2-1/2" diameter.

Concealed Partition Latch Keeper Bumper 1-1/4" Square Edge Cast Stainless Steel

Cast stainless steel construction. Keeper is 1-1/4" tall by 2-3/8" wide by 1-3/4" deep. The strike is a 1/2" thick and the slot is 7/16" deep. The opening to mount it on the square edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5963.

Shipped with screws for mounting.

400 Vinyl Stair Treads

Heavy gauge sharp-rib design Koroseal vinyl treads for heaviest traffic; 1/4" thick at wear area, easily trimmed to cover and fit any stair step. Install over concrete, metal, wood, terrazzo. Extra heavy thickness at the front "wear area". Meets Fed. Specs. RR-T-650E Type B. They are designed for interior use.

SPECIFICATIONS:

No. 400 Koroseal vinyl rib design stair treads 1/4" thick 12" deep; 1-1/4" square nose; contains no asbestos fiber; made of first quality homogeneous vinyl, color throughout thickness; free from imperfections which might lesson serviceability. Select standard length of 24", 30", 36", 42", 48", 54", 60", 72", 84" or 96". Select standard solid colors of Brown, Sand, Gray or Black.

Swivel spindle, 4-3/4" long
Two 3/8" solid centers
20 tpi

Dor-o-Matic 1690/1790 End Case Cover, or Hinge Case Cover

Doromatic part # ECAP.130 or PB314. Formly known as the ECAP.129

Color: Black