Search results for: '2004 right hand operator'

Heavy Duty Toilet Partition Gravity Hinge Set Lh Outswing, Rh Inswing Stainless Steel see diagram

1/8" thick stainless steel construction. 1-1/2" hole spacing up and down and 2-3/8" right to left hole spacing. Outside dimensions are 3-1/8" wide x 3" high. Also known as Bathroom Stall Gravity Hinge Sets. Manufacture part # 7052.

Includes all screws.

Wall Guard’s brushed stainless steel units measure 31.5”x15.5”x.06” and are designed to be installed under hand dryers. Provides protection for wall and makes clean up simple. Wall Guard can be used many different applications other than just under a hand dryer. Can be mounted around sinks, on restroom stalls or anywhere where to help prevent water damage. Known as World Dryers part number 37-10457K.

• Unit Size: 31.5”x15.5”x.06”
• Brushed Stainless Steel
• Mounted using Heavy Duty Double-Sided Adhesive Strips(Included)
• Easy Cleaning
• Modern Design

International Door Closer 854 Series

FEATURES
Two Adjustment Valves: Closing and Latching speeds controlled by separate regulating Valves, Universal application Non-handed for standard top
jamb or parallel arm installation.

Ships with regular arm and parallel arm bracket.

3/4" x 9-1/16" mounting holes

1" Q-Ball Floor Protector with Felt Base

The 1" Q-Ball Floor Protector with Felt Base is for use on 1" outside diameter chair and table legs. The adaptor shown on the right fits over your existing glide, and then the Q-Ball slides over the adaptor. Constructed of Gray Plastic.

Kit includes: Adaptor for 1" Leg, and Q-Ball with Felt Base

Grade 1 exit device
Device is non handed
Standard widths are 30", 36", 42" or 48"
3-3/4" minimum stile width

Replacement parts are also available

Plunger Type Holder / Stop FS1153

This plunger type door holder manufactured by H.B. Ives features a contemporary yet economical method of positive Hold-Open.  It is constructed in sturdy cast aluminum for years of service.  The spring operated plunger activates with minimal pressure, releasing instantly with a light tap on the plat-form lever.  The plunger offers a 1-5/8" throw for all types of doors.  The ribbed non-marring rubber shoe is securely fastened to unit with a screw and is easily replaced when worn.

Aluminum finish only

Ives Part # FS1153

Wall Guard’s white acrylic units measure 31.5”x15.5”x.06” and are designed to be installed under hand dryers. Provides protection for wall and makes clean up simple. Wall Guard can be used many different applications other than just under a hand dryer. Can be mounted around sinks, on restroom stalls or anywhere where to help prevent water damage. Known as World Dryers part number 37-10455K.

• Unit Size: 31.5”x15.5”x.06”
• White(Antimicrobial Acrylic-PVC Composite)
• Mounted using Heavy Duty Double-Sided Adhesive Strips(Included)
• Easy Cleaning
• Modern Design

Grade 1 Exit Device
Device is non handed
Standard sizes are 30", 36", 42" or 48"
Minimum stile width is 2"

Replacement parts are also available

Hand: Non-handed.
Finishes: US3 (605); US4 (606); US10 (612); US26 (625); US26D (626);
US32 (629); US32D (630); US28 (628), 313AN.
Strikes: 299 strike standard.
Latchbolt: Stainless steel, 3⁄4" throw.
Deadlocking Latchbolt: Standard.
Dogging Feature: 1⁄2 turn hex dogging standard. No threaded parts to wear out..
Doors: 1-3⁄4" thick, wood or metal. Specify thickness if other than 1-3⁄4".
Projection: 2-3⁄4" maximum, 2” dogged.
Mounting Height: 40-1⁄4" from CL to finished floor.
Fasteners: All mounting screws are concealed, sheet metal screws and machine
screws standard.
ANS I: Certified ANSI A156.3-2001 Grade 1 standards.
Center Case & Working Parts: Center case is heavy wrought and sintered metal parts.

Call for pricing on non listed finishes
2 week lead time

FEATURES

• Please note the factory will only sell in quantities of 10.
• Locks are individually keyed for single key access on a single lock
• Higher security 5-pin tumbler lock cylinder
• Rear mounted steel casing deters vandalism
• Locks have supervisory Control Key overide
• Each lock supplied with 2 keys
• Lock will work on both left and right hinged doors
• All Key Locks have a 5 year warranty from time of shipment
• 72 hour shipping available
  

APPLICATIONS

Fully retracting automatic spring latch for convenience

FEATURES

• Please note the factory will only sell in quantities of 10.
• Supervisory key control
• Ergonomic dial with grip ring and non-slip coating
• 7 pre-set combinations for extended usage
• 3-digit dialing combination with 5-pin tumbler key plug
• Patent pending button guard to protect lock function from overstuffed lockers
• Nut channels for easy installation
• All Built-in Combo Locks have a 10 year warranty from time of shipment
• 72 hour shipping available

APPLICATIONS

• For use with lock door hinged on top or bottom
• Manual dead bolt operation for higher security; recommended for ventilated lockers
• Fits all traditional locker styles

B-2112 Bobrick automatic wall mounted soap dispenser with satin finish in stainless steel. The vale dispenses all purpose hand soaps. Capacity 40 fl oz. The soap is refillable at the top and has an eye for soap level. The demensions are 8-1/8"w x 4-3/4" x 3-1/2"depth with push button included.

Truth/A.W. Anderberg 222SS 4 bar Egress Window Hinge

Used on larger casement windows to provide egress through the window.

Sold individually, these hinges are non handed

Truth/A. W. Anderberg part #35.11.00.102

The Yale 2701 is a non handed door closer that can be mounted push, pull or top jamb. The closer is adjustable 1-6 sizing, so it will work on any size door, interior or exterior.  The closer ships with a full cover, and all the mounting screws. This a Grade 1 closer, which is the highest rating possible. The mounting is 3/4 x 12 inches on centers.

International Door Closer 853 Series
FEATURES

Two Adjustment Valves: Closing and Latching speeds controlled by separate regulating Valves,

Universal application Non-handed for standard top jamb or parallel arm installation. Ships with regular arm and parallel arm bracket.

Direct replacement for the older style Norton 1602 and 1603, and Yale 52 and 53

3/4" x 8-3/16" mounting holes

• Non Handed
• Flush Mounted, No Inset
• 48" Maximum Door Width
• Beveled or Square Edge Doors, 83" long, cut to length

For Doors Weighing up to 450 pounds without reinforcing,
600 pounds with reinforcing

Effective December 20, 2024 the 2390 has been discontinued.  Falcon Doromatic is working on retro-fit plates to work with the 1690.

Doromatic 2390 Exit Device

International Door Closer 851 Series

FEATURES

Two Adjustment Valves: Closing and Latching speeds controlled by separate regulating Valves,

Universal application Non-handed for standard top jamb or parallel arm installation. Ships with regular and parallel arm bracket

3/4" x 6-3/8" mounting holes

International Door Closer 852 Series
FEATURES

Two Adjustment Valves: Closing and Latching
speeds controlled by separate regulating Valves,

Universal application Non-handed for standard top jamb or parallel arm installation. Shipped with regular and parallel arm bracket.

3/4" x 7-3/8" mounting holes

The Cal-Royal CRCODE204 is for use with the 2200, 7700 and 9800 Rim and Surface Vertical Rod Devices. The Lever Mechanism features a Break Away Lever, for use with 1-3/4 inch to 2 inch thick doors, non-handed, Single Code User, Key Override, easy on the door code change, weather resistant, and more than 8000 non-sequential possible code combinations.

Installation and Programming Instructions

The Monarch 712L Lever Trim is used for the XX-C, 18-C, and all 24 Series Falcon Devices.  The XX-C and 18-C are the obsolete concealed vertical rod Monarch Exit Devices. The Trim is non handed or field reversible. The Key locks or unlocks the Lever.  The escutcheon measures 1-3/4" wide and 7-1/4" long.

Falcon Spring-n-Stop Hold Open Arm, non handed, extra duty forged parallel arm includes an integral spring stop and non-adjustable forearm assembly for high volume traffic or abusive conditions.

Function is the Doromatic/Falcon Door Closer Model

Yale 4400 Door Closer

• Non-handed
• Rack-and-pinion design
• Cast aluminum body
• 2-1/8" (54mm) projection
• 1-1/2" (38mm) diameter piston
• 5/8" (16mm) diameter pinion journals
• Staked valves
• Standard, separate and independent, latch, sweep and
  backcheck intensity valves
• Backcheck positioning valve
• NorGlide® fluid
• Molded plastic cover
• All standard arm applications allow doors to swing 180°,
  conditions permitting
• Self-drilling screws
• Full-size template
• 10-year limited warranty

2-3/8" x 6-3/4" hole spacing. This door closer replaces the 4400BF. This newer version is Barrier Free Compliant.

The Falcon 8242 Automatic Opener is a smart and easy solution to improve accessibility and meet ADA Codes.  The 8242 is a non handed, surface mounted, 115 volt closer for a push side mounting.   If your door is an inswinging door you would use the 8231.   This self contained package features, an on board power supply, LED light on the control box to signal accurate installation and helps with connection diagnostics.  The package includes everything except for the actuators.

Falcon 8200 Catalog

Falcon 8200 Installation Instructions

The Falcon 8231 Automatic Opener is a smart and easy solution to improve accessibility and meet ADA Codes.  The 8231 is a non handed, surface mounted, 115 volt closer for a pull side mounting.   If your door is an outswinging door you would use the 8242.   This self contained package features, an on board power supply, LED light on the control box to signal accurate installation and helps with connection diagnostics.  The package includes everything except for the actuators.

Falcon 8200 Catalog

Falcon 8200 Installation Instructions

Tubing is 1″ diameter x 20 gauge with a satin finish. 42" Length will be as specified. Rod is held captive by flanges when installed properly. Rod may rotate in flanges if turned by hand. Correctly installed rod and flanges will support specified shower curtain(s) hung on hooks 1200-SHU or others. Rod will bend and pull from flanges if significant body weight is suspended.

Tubing is 1″ diameter x 20 gauge with a satin finish. 72" Length will be as specified. Rod is held captive by flanges when installed properly. Rod may rotate in flanges if turned by hand. Correctly installed rod and flanges will support specified shower curtain(s) hung on hooks 1200-SHU or others. Rod will bend and pull from flanges if significant body weight is suspended.

The Interkal Bleacher Wired Accupower Motor 1/4 Hp - 1 Phase is also known as K01151A100 or Part # P210709

Delivery of the Interkal Bleacher Wired Accupower Motor 1/4 Hp - 1 Phase we try to keep in stock at our facility for quick deliveries. The Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase is designed specifically for use in Interkal brand bleacher systems (Vectra bleachers), providing reliable power and performance. With a horsepower of 1/4, it is ideal for applications that require moderate lifting and lowering capabilities. The single-phase design ensures compatibility with standard electrical systems, making installation straightforward.

The Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase is built to last, featuring durable materials that can withstand the rigors of frequent use. Whether you are upgrading an existing bleacher system or replacing a worn-out motor, the Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase is a solid choice. For those looking to enhance their bleacher operations, the Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase offers smooth and efficient performance with 115 volts. With its robust design and user-friendly features, this motor not only simplifies the operation of your bleacher system, but also ensures safety and durability.

To maximize the benefits of your Wired Accupower Motor 1/4 Horsepower 1 Phase for Interkal bleachers (Vectra bleachers), regular maintenance is recommended. This includes checking connections, lubricating moving parts, and ensuring that the motor is free from debris. By taking these simple steps, you can extend the life of your Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase and maintain optimal performance.

If you have any questions about the installation process or compatibility with your current setup, feel free to reach out to our customer service team. We are here to help ensure that you get the most out of your Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase. If you ever need assistance, our dedicated support team is just a phone call or email away. We are committed to providing you with the best service possible, ensuring that your Wired Accupower Motor 1/4 Horsepower 1 Phase for Interkal bleachers systems operates smoothly and efficiently for years to come. The Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase is an excellent investment for anyone looking to enhance their seating arrangements. With its combination of reliability, efficiency, and ease of use, the Interkal Bleacher Wired Accupower Motor 1/4 Hp 1 Phase is sure to meet your needs and exceed your expectations.

International Door Closer 855 Series-Discontinued.   If you order this door closer the 885 will be sent, it is the same door closer but also features back check.

FEATURES
Two Adjustment Valves: Closing and Latching speeds controlled by separate regulating Valves, Universal application Non-handed for standard top jamb or parallel arm installation.

Ships with regular arm and parallel arm bracket.

3/4" x 9-1/16" mounting holes

Truth Telescoping Pole

Telescoping Pole with Hex Ball or Hook Drive
Rigid anodized aluminum poles feature free-turning ABS hand grips.
6 foot pole extends to 10 feet.

Truth Part # 10637 Hex Drive
Truth Part # 10638 Hook Drive

The Irwin Bleacher Drive Wheel is also known as Part # P5000IR.

The wheel is used with the Irwin & Folding Bleacher 6" Diameter x 9½" Wide x ¾" Axle with a keyway. The axle is 15⅛" long. Select one or two 20-tooth, 15-tooth, or 16-tooth sprockets.

The Irwin Bleacher Drive Wheel is durable and efficient, making it an essential component for any bleacher system. With its robust construction, the Drive Wheel for Irwin Bleachers ensures smooth operation and reliable performance, whether in a gymnasium or outdoor setting. Installation is a breeze, and with just a few simple tools, you can have your bleachers ready for action in no time. The 6" diameter and 9½" width provide stability, while the ¾" axle with a keyway ensures a secure fit. The Irwin Bleacher Drive Wheel’s design minimizes wear and tear, extending the lifespan of your bleacher system.

For maintenance, it's recommended to regularly check the Irwin Bleacher Drive Wheels for any signs of damage or wear. Keeping the Irwin Bleacher Drive Wheel clean and lubricated will help maintain optimal performance. If you need to replace a wheel, we offer the Irwin Bleacher Drive Wheel so that you can keep your bleachers in top condition. Whether you're managing a sports facility, school, or event venue, investing in quality components like the Drive Wheel for Irwin Bleachers will enhance the safety and functionality of your seating arrangements.

We recommend keeping a few spare Irwin Bleacher Drive Wheels on hand to minimize downtime in case of unexpected wear or damage. Regular maintenance checks should also include inspecting the bleacher structure itself. Look for any loose bolts, rust, or signs of structural weakness. Addressing these issues promptly can prevent larger problems down the line and provide safety for your patrons.

For questions about ordering the Irwin Bleacher Drive Wheel, feel free to reach out to our customer service team. We are always ready to assist you with any inquiries you may have regarding the Drive Wheel for Irwin Bleachers, from product specifications to shipping options.

Magnet Door Stop

Hands-free magnetic door stop/holder. All you need to do is open the door and a strong maget will keep it open until you close it. Mounts horizontally or vertically. Includes fasteners plus 1 concrete and 3 hollow wall anchors.

Not for use on doors with spring hinges or door closers.

• Standard top pivot for most offset pivot
sets and floor closers
• Oil-impregnated sintered bronze bearing
• Non-ferrous base metal
• 3/4"(19mm) offset (measured from
centerline of pivot to face of door)
• Furnished with wood and machine screws

Non Handed