Search results for: 'curtain hold horn roll size 1 inch'
-
Curtain Rod Kit, 1-1/4" x 60"
Kit includes rod with exposed flanges.
Flanges fabricated of 20ga. stainless steel with a satin finish. Flanges have (3) countersunk 13/64" dia. holes to accept #10 flat or oval head screws furnished by others.
Rod is installed in straight section between two (2) mounting flanges. Rods longer than 60′′ require ceiling hanger Model No 1204-C18.
For use with standard shower curtain model No ’s 1200 or 1200-V having 60′′ length and standard hooks Model No 1200-SHU unit should be installed with rod centerline 74-1/2′′ AFF or 67′′ above tub rim to obtain 6′′ bottom overlap.
CURT11/4x60 -
B-274 Bobrick Toilet Tissue Dispenser for Double Roll
B-274 Bobrick toilet tissue dispenser for double roll. The unit is made of a cast aluminum satin finish with a plastic spindle that is theft resistant. Holds up to one roll 6" diameter. The unit measures 12-1/2"w x 4-7/8" projecting out from the wall. This also has a controlled delivery.
B274 -
White Fabric Shower Curtain 48" x 72"
Shower Curtain - 10 Ga. White Vinyl, Order 8 Hooks Separately - 48"W X 72"H
Flame-resistant, anti-bacterial, 10 gauge white vinyl fabric with standard height of 72". Curtain should be 6" wider than opening up to 54" and 12" wider than opening exceeding 54".
Shower curtain should be attached with hooks (not provided, order separately) to rod (not provided, order separately). Known as 10-1200-V48 by American Specialties.
48X72P -
Curtain Rod Kit, 1" x 42"
Tubing is 1″ diameter x 20 gauge with a satin finish. 42" Length will be as specified. Rod is held captive by flanges when installed properly. Rod may rotate in flanges if turned by hand. Correctly installed rod and flanges will support specified shower curtain(s) hung on hooks 1200-SHU or others. Rod will bend and pull from flanges if significant body weight is suspended.
CURTAIN1x42 -
Curtain Rod Kit, 1" x 72"
Tubing is 1″ diameter x 20 gauge with a satin finish. 72" Length will be as specified. Rod is held captive by flanges when installed properly. Rod may rotate in flanges if turned by hand. Correctly installed rod and flanges will support specified shower curtain(s) hung on hooks 1200-SHU or others. Rod will bend and pull from flanges if significant body weight is suspended.
CURTAIN1x72 -
Curtain Rod Kit, 1-1/4" x 48"
Kit includes rod with exposed flanges.
Flanges fabricated of 20ga. stainless steel with a satin finish. Flanges have (3) countersunk 13/64" dia. holes to accept #10 flat or oval head screws furnished by others.
Rod is installed in straight section between two (2) mounting flanges. Rods longer than 48′′ require ceiling hanger Model No 1204-C18.
For use with standard shower curtain model No ’s 1200 or 1200-V having 48′′ length and standard hooks Model No 1200-SHU unit should be installed with rod centerline 74-1/2′′ AFF or 67′′ above tub rim to obtain 6′′ bottom overlap.
CURT11/4x48 -
White Fabric Shower Curtain 36" x 72"
Shower Curtain - 10 Ga. White Vinyl, Order 8 Hooks Separately - 36"W X 72"H
Flame-resistant, anti-bacterial, 10 gauge white vinyl fabric with standard height of 72". Curtain should be 6" wider than opening up to 54" and 12" wider than opening exceeding 54".
Shower curtain should be attached with hooks (not provided, order separately) to rod (not provided, order separately). Known as 10-1200-V48 by American Specialties.
36X72P -
International Door Closer 300 Series Adjustable Power
International Door Closer 300 Series Adjustable Power
UL Listed, Barrier Free Operation to Comply with Federal Accessibility Standards (ADA) ANSI A117.1. Spring Power adjustable for a range of sizes from 8-1/2 lbs t Medium Spring Tension, fully adjustable after installation.
Hydraulic Cylinder only
3000-B-310 105 with Hold Open
3000-B-311 105 with No Hold Open
3000-B-312 90 with Hold Open
3000-B-313 90 with No Hold Open3000-B -
LCN 4110 HEDA Hold Open Door Closer
Standard 4110 series closer shipped with EXTRA DUTY HOLD OPEN arm, standard plastic cover, 4110-201 FIFTH SCREW SPACER and self reaming and tapping screws. Sized cylinders adjustable for interior doors to 5’0” and exterior doors to 4’0”. Non-sized cylinder adjustable for interior doors to 4’6” and exterior doors to 3’6”. Closer mounts parallel arm, specify right or left swinging door. 4111 cylinder meets ADA requirements. The friction hold open arm allows for adjustable stop hold open positions up to 180 degrees.
We ship the 4111 HEDA
4110H- -
LCN 4110 HCUSH Hold Open Door Closer
Standard 4110 series closer shipped with HOLD OPEN CUSH N STOP arm, standard plastic cover, 4110-201 FIFTH SCREW SPACER and self reaming and tapping screws. Sized cylinders adjustable for interior doors to 5’0” and exterior doors to 4’0”. Non-sized cylinder adjustable for interior doors to 4’6” and exterior doors to 3’6”. Closer mounts parallel arm, specify right or left swinging door. 4111 cylinder meets ADA requirements. The cush hold open arm allows for a stop and hold open positions up to 110 degrees. "T" handle on arm will release door for closing, locking pin can be retracted for normal door closing operation.
We ship the 4111 HCUSH
4110HCUSH- -
Curtain Rod Kit, 1-1/4" x 42"
Kit includes rod with exposed flanges.
Flanges fabricated of 20ga. stainless steel with a satin finish. Flanges have (3) countersunk 13/64" dia. holes to accept #10 flat or oval head screws furnished by others.
Rod is installed in straight section between two (2) mounting flanges. Rods longer than 42′′ require ceiling hanger Model No 1204-C18.
For use with standard shower curtain model No ’s 1200 or 1200-V having 42′′ length and standard hooks Model No 1200-SHU unit should be installed with rod centerline 74-1/2′′ AFF or 67′′ above tub rim to obtain 6′′ bottom overlap.
CURT11/4x42 -
Cal Royal 7000 Alarmed Exit Device
Cal Royal 7000 Alarmed Exit Device
Same as the Cal Royal 7700, but with these added features"
Alarm unit has internal horn. When the push rail is depressed, the horn sounds to provide an audible means of signaling that the door has been opened and violated. The unit has changeable 2 minute alarm cutoff or manual reset. Preset at factory for 2 minute alarm cut off. The key switch to turn alarm off is a standard 1 ¼” cylinder with “C” keyway. The alarm operates on one standard 9 volt transistor battery. When battery is weak the horn will emit an intermittent signal. Alarmed units are supplied with a switch that monitors push rail only. Unit includes “EMERGENCY EXIT ONLY • ALARM WILL SOUND” decal for application on door or unit.
ALRM7700 -
Push Plate 80 Series 1/8 inch Round Bevel
The 80 Series Push Plate is similar to the 70 series, but has a round bevel on the top and bottom of the plate. There is no bevel on the sides. These plates are an 1/8 inch thick and are available many different finishes and size. Custom sizes are available, and they ship with the matching finish mounting screws.
GPH80- -
Crash Chain Door Stop CS115
Crash Chain Door Stop CS115
- Specially designed for full-size exterior doors.
- Tear resistant, grey vinyl cover.
- Heavy duty compression spring assembled to both ends of chain
and end brackets. - Packed with sheet metal screws.
- Cast Brass brackets with solid, welded steel chain.
Available in 20-1/2", 25-1/2" and 30-1/2" lengths. Length is determined
by the location of your door closerPART # LENGTH
GCC205 20-1/2"
GCC255 25-1/2"
GCC305 30-1/2"GCC205- -
Specta Rib Olefin Carpet Mat
SPECTRA RIB CARPET MAT-OLEFIN
Ribs that scrape, valleys that hold dirt and moisture. Ribbed carpet surface wipes shoes better, saves on clean up time of your floors. Shaded carpet effect brightens your entryway.
Available in Stock Sizes or Custom Lengths 24", 36" or 48" wide.
See more views box for colors.
SRXX -
1-1/4 inch Tube Cap
1-1/4" Tube Cap
Round Tubing - 6 prong Tube Caps are pushed in easily and hold securely in 16 or 18 gauge round tubing. Sold individually.
Fits 1-1/4" outside diamter legs, 1-1/4" base diamter
Nickel Base Finish
TC125 -
Easy Sweep Rib Runner Mat
Non-fading superior aging properties make this oil, grease, chemical and stain resistant matting a popular item. Non-combustible; tear, cut, impact and ozone resistant; high tensile strength and elongation properties; single piece rolls. Use inside or outside. Round ribbed corrugations run lengthwise, easily cleaned with soap and water.
GREASE AND OIL RESISTANT — NO FABRIC
Pricing below is per linear feet, Black Only, Size is the Width
MXXX -
Roll Type No Touch Towel Dispenser Dark Translucent
Roll Type No Touch Towel Dispenser Dark Translucent
The Electra Touchless Roll Towel Dispenser provides maximum options and cost reduction. It features adjustable paper lengths (9", 12", 15") and time delay (1, 2, 3 seconds). Our patented paper-savings mode reduces paper consumption by 12-15%. An automatic transfer system eliminates stub roll waste. Three choices for colors, Dark Translucent, Black translucent and White.
9AT225T -
Swivel Glide 5/8 inch O.D. X 1/2 inch I.D. Without Ferrule
Metal Based Swivel Chair Glide for a round tubing chair leg with a 5/8" O.D. X 1/2" I.D. This glide has a clip that holds the glide on by going inside the chair leg. The Chair Glides Base diameter is 1 1/4".
SGR62I -
1 inch Tube Cap
1" Tube Cap
Round Tubing - 6 prong Tube Caps are pushed in easily and hold securely in 16 or 18 gauge round tubing. Sold individually.
Fits 1" outside diamter legs, 1" base diamter
Nickel Base Finish
TC100 -
Pilaster Shoe for 1-1/4" Thick x 3" ht
Toilet partition square edge pilaster shoe split, stamped stainless steel construction. Pilaster Shoe measures 2" to 24" wide by -1-1/4" thick by 3" high. This size pilaster post shoe is split on one end for easy installation. Also known as a bathroom stall pilaster post shoe square edge. Used for the base of the support system with floor mounted pilaster.
9A0306 -
Lifetime Polished Brass Kick Plate
Lifetime Polished Brass Kick Plate US3 PVD -16 Ga (.050")
Stainless steel plate with a highly durable polished brass looking finish.
Custom sizes available starting around $0.40 per square inch depending quantityKick Plate comes with matching Phillips Head screws for mounting
Please allow 1 week shipping time
GKP-US3-PVD -
Saddle Threshold 613 - 6" Wide By 1/4" High
Saddle Threshold 613 - 6" Wide By 1/4" High
Extruded aluminum construction. The thresholds are shipped with mounting screws (#10 x 1-1/2" FH zinc plated wood screws), Milled aluminum finish. This is considered a Handicap Saddle Threshold.
Other sizes and finishes are available, call for more information.
Air shipment is not available on this product. Please allow 7-10 days for delivery.
613- -
Polished Stainless Steel Kick Plate US32
Polished Stainless Steel Kick Plate US32
Polished Stainless Steel US32 Kick Plate 16 Ga (.050"). These plates have the same appearance as polished chrome, but are a lot more durable. Custom sizes available starting around $0.37 per square inch depending quantity
Please allow 1 week shipping time
Kick Plates come pre drilled with screws.
GKP-pol-ss -
Round Tubing 5/8 inch O.D. X 1/2 inch I.D. Spring Clip
Threaded spring clip for round legs. 1/4-20 thread for use with our LA10625 and SLA12525. 5/8" outside diameter, 1/2" inside diameter with a 1/4-20 thread. This clip has an outside holding clip.
CLR62N





































