Search results for: 'locker number tabl 1 3 hold stop'

Hussey bleacher 1/2 horsepower, Three phase, rpm 1725, 208 volt, Note this is commonly used with 70:1 or 60: 1 Hussey gearboxes. Used with for Power III & Power Trac IV.

Lyon Folding Chairs metal Attaching Hardware set for all 4 legs. This is necessary to keep the chair tip in place. Lyon part number 1598. 

Republic Steel 30" dt Lock Bar-26-3/16" Length, Latch finger 701730 included, uses 700308-700309 handle assembly. Also known as 7627751, 75330, 2830, rs3026, lr230.

Toilet Partition Bottom Hinge Assembly For 7/8" Door, 1-1/4" Pilaster

Polished chrome plated zamac die cast construction. Kit includes Bottom Hinge, Pintle, Nylon Cam, and Bottom Hinge Door Insert. Bottom hinge measures 2-1/4" high by 1-1/4" wide with screw spacing of 1-1/2". Mounting lug projects out 1-1/4". Also known as a Bathroom Stall Bottom Hinge Kit. Manufacture part number 63010.

Screws are also included.

Threaded Stem Single Wheel Caster -3" Wheel -3/8-16 Thread, 1 1/2" long stem. Zinc finish with black rubber wheels. Available for treads for carpet and non carpet areas. 

KK7641 for Hard Tread for Carpet

KK7462 for Soft Tread for Non Carpet Surface

Friction Ring Single Wheel Caster - 3" Wheel - 7/16" Stem Diameter, 1" stem length, 3" wheel diameter. Zinc finish with black rubber wheel. Available with tread for carpet and non carpet areas.

KK5741 hard tread for carpet

KK5742 soft tread for non carpet

Partition Door Kit Inswing 1" Door & Post Cast Stainless Steel. All hardware screws included for installation of these products. All hardware is a gravity close so your door self closing every time. Also known as part number 11303.

The International Flushbolt Standard Guide is the piece that fits into the top or bottom of the door and acts as a guide for the Flushbolt Rod.  The piece measures 1-3/8" x 1-1/2".  The square hole in the piece is a 1/2" square.  The manufacture part number is FG-1200.

Chrome plated inswing door kit for square edge doors and posts. For 1" doors and 1" post. All hardware screws included for installation of these products. All hardware is a gravity close so your door self closing every time. Also known as part number 11300.

Partition Keeper Bumper Inswing 1" Square Edge Cast Stainless Steel

Cast stainless steel construction. The strike and keeper is 2-1/2" tall by 1-15/16" wide. The mounting holes are 1-1/2" on center. The stop is 2-1/2" tall by 13/16" projection with a rubber insert. The two slots are 5/16" deep by 13/16" high. Also known as Bathroom Stall Strike and Keeper Inswing 1". Manufacture part # 5823.

Shipped with mounting screws.

• Shower Room Benches require 2 pedestal's not included. 
• Locker benches shall be laminated selected hardwood 1-1/4" full finished thickness.
• All corners are to be rounded and sanded.
• Surfaces shall be finished with two coats of clear lacquer.
• Available Bench Tops are to be 9-1/2" wide and furnished in lengths of 3' through 12' (even foot increments).

Euro Style Support Brace for 3/4" thickness material. Available in 4"-4-1/2", 6-6-1/2" and 9-9-1/2" height, all adjustable by a 1/2". Heavy duty industrial #304 stainless steel material. References part numbers are 189003, 189013, 189023. 

Stainless Steel Torque Head Barrel Nut Shoulder Screw for 1/2" - 3/4" Gripping. Use with torque driver bit T27 for toilet partition security screws. 10-24 thread, stainless steel unplated and uses a 6 lobe  head torque. Both pieces included.

LCN Arm Screw

This screw goes by the number 4040-159, 4110-159, 4020-159, 1260-159, 1260-159, 4040-159 and 4040SE-159.   The screw has a 3/4" diameter head, 1/2" high with a 1/4" diameter shaft with 20 threads per inch (1/4-20 screw).

Threaded Stem Twin Wheel Caster -2-3/8" Wheel -3/8-16 Thread, 1 1/2" long stem. Chrome hood with black wheels. Available with tread for both carpet and non carpet areas. 

KK8421 for hard tread for carpet

KK8422 for soft tread for non carpet surfaces

Stainless Steel Torque Head Barrel Nut Shoulder Screw for 7/8" - 1-3/16" gripping. Use with torque driver bit T27 for toilet partition security screws. 10-24 thread stanless steel unplated and uses a 6 lobe head torque. Both pieces included.

Cast stainless steel outswing door kit for square edge doors and posts. For 1" doors and 1" post. All hardware screws included for installation of these products. All hardware is a gravity close so your door self closing every time. Also known as part number 21343.

Our replacement Republic Storage Handles are based on the version they produced in the 1970′s, which means more material on the legs (lugs) and housings. The extra material makes them much more heavy duty then the ones they are producing today. We used to sell the Republic Storage #12 Locker Handle three ways, just the lift, just the case or the complete assembly, however we are no longer able to procure the components individually. The case and the assembly come with the mounting screws. The Republic Storage #12 handle, also goes by Republic Steel #12 handle, and Berger #12 handle. The #12 handle has been produced since the 1965 and is still produced today. Also known as 70102, 2030, 70001, rs1106, lr302.

7/8" Q-Ball Floor Protector with Felt Base for use on 7/8" outside diameter chair and table legs.The adaptor shown on the right fits over your existing glide, and then the Q-Ball slides over the adaptor. Constructed of Gray Plastic. Kit includes: Adaptor for 7/8" Leg, and Q-Ball with Felt Base

Include Master key #, always starts with a "SL" and has 2-3 numbers after it.

or new series. We will need your master key number if adding to your existing system.

Truth 16.27 Sash Lock. Sometimes known as the Truth Entrygard Sash Lock.

3" high x 2-9/16" deep x 1" thick.  We sometimes find the numbers 45208 or 40707 cast into this part.

Left hand sash lock shown in picture.

2-3/8" between screws

Friction Ring Plastic Inserts For Round Legs with a 7/16" diameter friction ring casters only. 

Tubing Inside diameter / Part #'s

5/8" KK5A31
3/4" KK5A32
7/8" KK5A34
15/16" KK5A35
1" KK5A36
1-1/16" KK5A37
1-1/8" KK5A38

Toilet Partition Continuous 'U' Wall Bracket For 1" Thick Panel 57" Long Stamped Stainless Steel

18 gauge (.05" thick) stamped stainless steel construction. Base is 1-1/8" x 57" long. Legs project out 1-1/2" with the thru hole at 1-1/8" from the base. Mounting and thru bolts every 13" or so. Also known as a Bathroom Stall Continuous U Wall Bracket. Manufacturer part # 2369.

Screws included with bracket.

Truth 10005 Replacement Shoe

The metal part is 1-1/8" x 15/16". The plastic piece is 1-3/8" with a .280" diameter

Used on Truth Awning Operator number 11.16 and 11.44.

Hadrian Aluminum Headrails for 1"X60" Type A used on overhead braced floor mounted partitions. For Hadrian Powder Coated Steel and Stainless Steel Partitions. The headrail goes between a U shape which is 1" for the headrail to fit into at the top of the pilaster, the headrail bolts to the pilaster for stability at the top. Also known as part number 580060.

Hadrian Aluminum Headrails for 1"X74" Type A used on overhead braced floor mounted partitions. For Hadrian Powder Coated Steel and Stainless Steel Partitions. The headrail goes between a U shape which is 1" for the headrail to fit into at the top of the pilaster, the headrail bolts to the pilaster for stability at the top. Also known as part number 580074.

Hadrian Aluminum Headrails for 1"X96" Type A used on overhead braced floor mounted partitions. For Hadrian Powder Coated Steel and Stainless Steel Partitions. The headrail goes between a U shape which is 1" for the headrail to fit into at the top of the pilaster, the headrail bolts to the pilaster for stability at the top. Also known as part number 580096.

The Matte Black Hadrian 1/2" Pedestal Support Brace is constructed of stainless steel. Pedestal support brace is used in place of a traditional pilaster where the pilaster anchors to the ground. This pedestal support brace allows pilasters to be off the ground but still provide structure to partitions. Designed to be used under a pilaster or panel that is 1/2" thickness. Available in 12", 9" and 4" heights and comes with fasteners for installing. Known as manufacturers part number 673441-12AF-BLK, 673441-9AF-BLK and 673441-4AF-BLK.

Von Duprin 050535 El Solenoid Assy

Discontinued, we do not have any stock remaining.  You would have to order the QEL or QEL-HD Conversion Kit to update your exit to the new Mechanical Electric Latch Retraction:  https://www.robertbrooke.com/von-duprin-qel-baseplate-conversion-kit.html

Screws are 1" on center, the cylinder measures 3" long by 1-3/4" diameter. Used on the 33A, 35A, 98 and 99 exit and panic devices. This Solenoid Assembly is also used on the Doromatic/Falcon EL1690, EL1790 and EL2390

We sometimes find the number 971687, along with 4011 VDC 24

Von Duprin Part Number 050535
Doromatic/Falcon Part # 971687-00

Bobrick Toilet Partitions Inswing Keeper Bumper For Throw Latch For 1" Sq Edge Post

Polished chrome plated Zamac construction. The strike and keeper is 2-1/2" tall by 1-15/16" wide. The mounting holes are 1-1/2" on center. The stop is 2-1/2" tall by 13/16" projection with a rubber insert. The two slots are 5/16" deep by 13/16" high. Also known as Bathroom Stall Strike and Keeper Inswing 1". Manufacture part # 5820.

Shipped with mounting screws.

Friction Ring Plastic Inserts For Square Chair Legs for 7/16" diameter friction ring casters only. 

Tubing Inside diameter / Part #'s

5/8" KK5A41
3/4" KK5A42
7/8" KK5A44
1" KK5A46
1-1/8" KK5A48

Torque Head Barrel Nut Shoulder Screw for 7/8" - 1-3/16" gripping. Use with torque driver bit T27 for toilet partition security screws. 10-24 thread chrome plated and uses a 6 lobe  head torque. Both pieces included.

1525 master lock combination padlock. Standard 3/4" vertical shackle.
Keyed controlled & Combination.
Master key sold separately. We will need your master key number if adding to your existing system. These keys start with a "V" and has digits after it.

1-2 week lead time

Concealed Latch Keeper Bumper Outswing Cast Stainless Steel

Cast Stainless Steel casting. The strike and keeper is 1-1/4" high by 1-3/4" deep by 1/8" thick. The stop is 1/2" deep by 1-1/4 wide with a rubber insert. Also known as a Bathroom Stall Strike and Keeper Outswing Flat. Manufacture part # 5643.

Shipped with mounting screws.

Comtec Toilet Partition 8" Wrap Around Hinge Set. Clear anodized aluminum for 1" panel and 1" door. Used by every Bathroom Toilet Stall manufacture on Solid Plastic Toilet Partitions Doors. Sometimes known as part numbers, 7978, 7988, 8974, 8984. These hinges are reversible by taking the 3 pieces apart and reconfiguring the opposite swing.