Search results for: 'good 8 draw based door hold'

Square Plastic Chair Tips for Straight Square Tubing chair legs with a  3/4" Outside Diameter X 5/8" Inside Diameter. Available in black only. 

Accurate Door Kit Old Style, Used January 1-2013 to September 2021. This door kit includes all you see and the security screws. Also known as 40-8261505. Made of cast stainless steel.

Republic Steel Locker Door Jamb RH, for Prior to Current. Right hand shown in picture. For locker hinges on the right side facing the lockers. Made in the USA., Hole spacing 2" on centers. Also known as 70303, 2703, 70031, rs1133, lr334.

The Von Duprin Dogging Adaptor is the female part that holds the dogging shaft in place.

Von Duprin dogging assebly part

#1 on diagram

Von Duprin part # 090043

Sold individually

Half Mortise 4-1/2" Door Hinge-Box of 3

Steel construction, five knuckle, two bearing, square edge, Half Mortise 4-1/2" Door Hinge.  Sold in boxes of 3 hinges, ships from California.   Available in Brushed Chrome and Paint Primed (gray).

Von Duprin 360L Lever Trim

The Von Durpin 360L Lever Trim has a base measurement of 7-1/2" high by 1-11/16" wide and 7/8" thick. The lever is 4-1/2" and projects out 3". This lever Trim uses a 1-1/4" Mortise Straight Cam Cylinder.

Von Duprin Part # 360L

Toilet Partition Continuous Toilet Partition Hinge 57-1/2" With Spring Close Stainless Steel
Rh Inswing or Lh Outswing See Diagram

16 gauge (.060" thick) stainless steel with 4 springs. 3" wide when laid flat x 57-1/2" long. 1/8" diameter hinge pin. Mounting screws are located every 11" or so. Can be raise up 3/8" for emergency entrance. Also known as a Bathroom Stall Piano Hinge, or Full Length Stainless Steel Continuous Piano Hinge. Manufacture part # 7659.

Shipped with all the fasteners

Toilet Partition Pilaster Floor Shoe 1-3/4" X 1-3/4" Square Post

Constructed of zamac die cast material, then polished chrome plated. Base is 2-5/32" x 3-7/8", with 3" on center hole spacing. Floor shoe projects up 2" and has a 1/4-20 treaded hole. Also known as a Bathroom Stall Pilaster Post Shoe, or Toilet Partition Pilaster Post Shoe. Manufacture part # 3040 and 40-8512510. Shipped with all the fasteners.

Handless Window Fastener 1-3/8"

Cast white bronze with a brushed nickel finish

"C" Fold or Multi-Fold
Heavy duty steel back with impart resistant plastic front
Holds 540 multi-fold or 350 C-fold towels
11"w x 15"h x 4" d

85 Series Tube Balances, 5/8" Diameter.

This is the most common type of tube balance out there.

Partition Door Pull 3-1/2" Between Screws Cast Stainless Steel

Cast stainless steel construction. The pull measures 4-3/4" wide and projects 1" with a hole spacing of 3-1/2". The mounting holes are threaded for a 10-24 screw. Also known as a Bathroom Stall Door Pull. Manufacture part # 5403.

Stainless Steel Door Hook Fix it kit comes with stainless steel plate 3"x3", stainless steel hook and screws included. Also known as 115523. Hook projects 3" also known as 4113 or 4003.

Republic Steel Locker Door Jamb LH, for Prior to Current. Right hand shown in picture. For locker hinges on the left side facing the lockers. Made in the USA., Hole spacing 2" on centers. Also known as 70304, 2703, 70041, rs1134, lr335.

The LCN 1260 Series combines the best features from the previous 1070 and 1370 into a single versatile and economical cast iron closer, with dual mounting capability. The 1260 is adjustable spring sizes 1-5 and mounts to the most common commercial footprint. The 1260 also features a complete line of regular and extra duty arms, LCN’s peel-n-stick installation templates, a convenient spring adjust pointer. The Brass finish is Painted Brass.

We ship the 1261 Rw/PA

"C" Fold or Multi-Fold
Heavy duty steel back with impart resistant white plastic front
Holds 540 multi-fold or 350 C-fold towels
11"w x 15"h x 4" d

Replacement Shoe For Mickey Door Stop Holder

Replacement shoe for the GJX2M Grand Specialties 3" Mickey Door Stop.

Product Description & Features
• Total Projection: 1-13/16" (46mm)
• Mounting Requirements:
2" x 4" x 2-1/2" (51 x 102 x 64mm) outlet box
• Wall must be properly reinforced and outlet box
adequately fastened
• UL listed door holder

Chrome plated Zamac die casting construction. Coat hook bumper projects out 3" and has a rubber insert. The hook projects out 1-7/32". The coat hook bumper base is 1-7/16" wide by 2-1/4" high with a hole spacing of 7/8". Also known as a Bathroom Stall Hook. Manufacture part # 4000.

Interkal Bleacher Seat Nose Beam Shoulder Bolt 2-3/4" x 3/8"-16 Thread. The bolt has a shoulder collar of 1/2" diameter x 1-1/4", the thread length is 1-1/8". Used with seat modules to bolt the chair to the frame of the bleachers.

#14 x 5/8" Screw 6 Lobe(T-27), Chrome, 7/16" diameter head, also known as 92193. This uses a Torx bit to drive screw.

Ives 7212 Pivot Set

• Handed
• Top, header mount
• Bottom, jamb mount
• Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
• Maximum door load 200 pounds
• Vertical adjustment range 3/16", with positive locking

Handing diagram

The International Flushbolt Standard Guide is the piece that fits into the top or bottom of the door and acts as a guide for the Flushbolt Rod.  The piece measures 1-3/8" x 1-1/2".  The square hole in the piece is a 1/2" square.  The manufacture part number is FG-1200.

Lyon metal Locker Door Jamb, Used September 2004 - Current. Also known as 6727.

Hussey Bleacher Wheel 5" x 1-3/16" x 3/8". Also known as 2011007. Load approx. 190 - 210 lbs.

Dor-o-Matic 1690 Pinion Support Bracket. Bracket holds pinion tip so that it will not slip

Doromatic part # BRKT.478, BRKT.133 or PB312

Dor-o-Matic 1690 Repair Parts Breakdown

Accurate Stainless ADA Door Kit Old Style, Used January 1-2013 to September 2021. This door kit includes all you see and the security screws. Also known as 50-8261515. Stainless steel material.

Plastic Chair Tips Square Tubing for 7/8" Outside Diameter X 13/16" Inside Diameter. Fits square tubing legs with an outside diameter of 7/8" and an inside diameter of 13/16". Available in black. 

#10 x 5/8" Long Screw 6 Lobe(T-27) Chrome, 7/16" diameter head, Also known as 90963. This uses a Torx bit to drive the screw.

The 538 Automatic Door Holder is constructed of cast brass, and then chrome plated. The wall mounted strike has a pivoting head to adjust to different angles. The Holder/Stop measures 3-11/16 x 3 inch base, the stop projects out 1-15/16, and the strike projects out 3-1/4 inches. Holder/Stop ships with fasteners.

Only available in Brushed Chrome Finish.

LCN SEM7810-514 Coupler Assembly Kit