Search results for: 'roll board partition partit'

Bobrick B-35639 surface mounted waste receptacle with disposal door in a satin finish stainless steel all welded construction. The door is secured to cabinet with a concealed full length stainless piano hinge. Equipped with a cable door swing limit and tumbler lock. Waste bin constructed of heavy gauge stainless steel. The unit is a 3 gallon capacity and is 14-13/16"w x 28-3/16"h x 4-1/2" depth.

Zamac die cast construction, polished chrome finish. Latch base is 4" high with 2-3/4" hole spacing. Latch bolt is 3-3/16" long by 3/4" wide by 3/16" thick. The latch bolt clearance is 9/16" from the back of the base to the under side of the latch bolt and projects out 15/16". The latch projects out 1-9/16" from the face of the door when installed. Also known as a Bathroom Stall Surface Mounted Slide Bolt Latch. Manufacture part # 5020.

Shipped with mounting screws.

Gravity Hinge Set Cast Stainless Steel For Rh Inswing, Lh Outswing - See Diagram

Hinge is 3/32" thick stainless steel. They measure 3-1/4" wide x 2-29/32" high outside dimensions. 1-1/2" hole spacing up and down 2-7/16" right to left hole spacing. Also known as a Bathroom Stall Surface Mounted Hinge Set. Manufactures part # 7033.

Shipped with the fasteners.

Gravity Hinge Set Cast Stainless Steel For Lh Inswing, Rh Outswing - See Diagram

Hinge is 3/32" thick stainless steel. They measure 3-1/4" wide x 2-29/32" high outside dimensions. 1-1/2" hole spacing up and down 2-7/16" right to left hole spacing. Also known as a Bathroom Stall Surface Mounted Hinge Set. Manufactures part # 7043.

Shipped with the fasteners.

WingIt Grab Bar Fastener for extra strength mounting grab bars. The wingit 251-4 is designed to work for a hole 2-1/2" and 3-1/2" or deeper hollow walls with finished wall surfaces 1/4" to 1-1/2" thick. Material used is a corrosion resistant stainless steel. One require for each flange. Fasteners will support up to 300 lbs load. Also known as 251-4.

B-40 Bobrick surface mounted soap dispenser in a two tone black and grey color. Valve dispenses all purpose soaps. No lock with easy refills. Translucent container provides a visible soap level. The capacity is 40 fl oz and can mount to a mirror if needed. The unit is 5-13/16"w x 6-7/8"h x 3-3/16" depth to push button.

Outswing Keeper Bumper, 1-1/4" Post Sq Edge

Zamac die cast and polished chrome plate construction. Keeper is 1-1/4" tall by 2-3/8" wide by 1-13/16" deep. The strike is 1/2" thick with rubber insert. The opening to mount it on the square edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5970

Shipped with screws for mounting.

The Matte Black Hadrian Door Kit is designed to work with doors and pilasters that are 3/4" thickness. Hinges, Coat Hook and Latch Keeper are constructed of stainless steel and indicator latch is constructed of zamac with all having a matte black finish. The door kits comes with (2) Hinges, (1)Indicator Latch, (1) Latch Keeper, (1) Coat Hook and fasteners for installing. Hinges are field adjustable so door and swing in or out as well as right or left. Known as manufacturers part number 671000-BLK.

General Keeper Bumper For Concealed 1-1/4" Round Edge

Polished chrome plate Zamac die casting construction. Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5510.

Shipped with mounting screws.

Bobrick fixed position tilt mirrors known as B-293 series. These mirrors are ADA approved and are required for commercial restrooms that provide handicap accessibility. The frame is type 304 stainless steel with beveled edges of the frame hug the mirror. This provides a gapless fit for improved appearance and safety when cleaning. The product is a plate glass. The mirror extends 4" from the wall at the top and tapers down to 1" at the bottom.

Bobrick Trimline series surface mounted napkin/tampon dispenser with two models to choose from. The unit is satin finish stainless steel on exposed surfaces and is 13-7/8"w x 28"ht and has adjustable flange surface mounts. Choice of Free or .25 cents for your customers. The model #'s B-370639-25 and B-370639-C are the two that we offer, see detailed sheet for more information.

Bobrick Contura series surface mounted napkin/tampon dispenser with two models to choose from. The unit is satin finish stainless steel on exposed surfaces and is 14-3/8" w x 28-3/8" ht and has adjustable flange surface mounts. Choice of Free or .25 cents for your customers. The model #'s B-47069-25 and B-47069-C are the two that we offer, see detailed sheet for more information.

Metpar concealed Ada lever latch knob with cover. Zamac die cast construction with polished chrome plating. Outside diameter of the knob and cover are 1-3/4" with the inner ring diameter of 1-7/32". The latch bolt is 11/32" diameter by 2-21/32" long, the square box has a height of 3/4". Also known as a bathroom stall concealed ADA lever latch cover and knob assembly or a barrier free concealed latch knob, Cover and pin. Manufacture part # 6080.

Metpar Bottom Hinge 1-1/4" Square Edge Post Or Pilaster

Chrome plated Zamac die cast construction. The bottom hinge U channel measures 1-1/4" deep by 2-1/4" high with an insert depth of 1-5/16". The hole spacing is 1-1/2" between screw holes. The hinge lug projects out 1-9/16" by 1/2" thick with a 5/16" diameter hole. Also known as a Metpar Bathroom Stall Pivot Hinge - Bottom 1-1/4". Manufacture part # 3430.

Shipped with mounting screws.

A=1-9/16"

General Top Hinge For 1-1/4" Round Edge Post

Chrome plated Zamac die cast construction. Pivot hinge is 2-3/16" tall by 1-1/4" wide. The slot that wraps around the post is 1-1/4" wide and 11-16" deep. The hole spacing is 1-1/2" on center. The lug projects out 1-1/2" and is 1/2" thick. The bushing on the lug is 3/8" diameter. Also known as a Bathroom Stall Pivot Hinge Top 1-1/4". Manufacture part # 3510.

Shipped with mounting screws.

A=1-7/6"

Selling Bobrick channel frame plate glass mirrors. Type 430 stainless steel with bright polished finish with mitered corners. Frame screw permits easy replacement of glass. 1/4" thick glass mirror with 1/2"x1/2"x3/8" stainless framing. Secured to concealed wall hanger with theft resistant mounting. Known as the B-165 series channel frame mirrors.

Bobrick stainless steel straight grab bars for 1-1/2" diameter with a snap on flange to conceal the screws. Type 304 stainless steel tubing. Maximum weight capacity is 250lbs Known as B-6806x18, B-6806x36 and B-6806x42.

Cast Stainless Steel Top Hinge for 1-1/4" Sq Edge

Cast Stainless Steel construction. The hinge measures 2-1/4" high by 1-1/4" wide. The U channel is 2-1/4" by 1-1/4" by 1" deep. The lug projects out 1-5/8" by 1/2" thick with a 3/8" diameter bushing. Also known as a Bathroom Stall Pivot Hinge Top 1-1/4". Manufacture part # 3793

a=1-11/16"

also known as general, american sanitary, flush, fiat

Outswing Keeper Bumper, 1-1/4" Round Edge

Polished chrome plate Zamac die casting construction. Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5570.

Shipped with mounting screws.

Zamac die casting that is polished chrome plated. The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. The latch bolt slot is 1-9/16" high by 5/16" deep. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for inswinging doors. Also known as a Bathroom Stall Strike and Keeper-Inswing 1-1/4" Square Edge. Manufacture part # 5110. Shipped with mounting screws.

Scranton Stealth Brackets for Integral Hinges 4 brackets included. These brackets help support the plastic pins used with the integral hinge pin system. These brackets help to reinforced the hinge pins so they do not break or the door breaking at the top and bottom.

American Sanitary Slide Bolt Latch Chrome Plated.

Zamac die cast construction, polished chrome finish. Latch base is 4" high with 2-3/4" hole spacing. Latch bolt is 3-3/16" long by 3/4" wide by 3/16" thick. The latch bolt clearance is 9/16" from the back of the base to the under side of the latch bolt and projects out 15/16". The latch projects out 1-9/16" from the face of the door when installed. Also known as a Bathroom Stall Surface Mounted Slide Bolt Latch. Manufacture part # 5020.

Shipped with mounting screws.

Comtec Out Swing Flat Stop 6"

Clear Anodized aluminum construction. The strike and keeper is 6" tall by 1-5/8" deep by 1/8" thick. The stop is 9/16" deep by 3/4" wide with a rubber insert. The mounting holes are 3" on center. Also known as a Bathroom Stall Flat Backed for Wall Mounting Strike and Keeper. Manufacture part #5898.

Shipped with mounting screws.

The 2½" Aluminum Bleacher Clip is also known as Part #P2041U.

The 2½" Aluminum Bleacher Clips feature grooves 2-1/8" for the outer groove and 1" apart are the inner grooves. This clip replaces the 2-1/8" smaller version clip. You would use the outer and inner groove to make 1-3/4" between grooves. The 2½" Aluminum Bleacher Clip package includes a bolt and nut which are zinc cadmium plated.

Make your bleachers safe and secure with the reputable 2½" Aluminum Bleacher Clips. The durable 2½" Aluminum Bleacher Clips are designed to securely fasten bleacher seats to the supporting structure, ensuring safety and stability for spectators. Installation involves a quick setup and adjustments as needed. Each 2½" Aluminum Bleacher Clip is engineered to withstand heavy use, providing peace of mind during events. Made from high-quality aluminum, 2½" Aluminum Bleacher Clips hold up against rust and corrosion, making them ideal for both indoor and outdoor use. Whether you are managing a sports facility, school auditorium, or community center, the Aluminum Bleacher Clips 2½" are an essential component for maintaining the integrity of your bleacher system.

In addition to regular inspections, it is important to stay educated about the proper use and maintenance of the bleachers with information and/or training to help ensure that all staff understands how to operate the bleachers safely and effectively. Encourage your team to report immediately any replacements needed—whether it's loose 2½" Aluminum Bleacher Clips or damaged boards—so that repairs can be made promptly. We recommend keeping a maintenance log to track inspections and repairs for your bleachers. This can help you stay organized and ensure that nothing is overlooked. Regular maintenance not only enhances safety but also improves the overall appearance of your bleachers, making them more inviting for spectators.

For more information on specifications of the Aluminum Bleacher Clips 2½", please feel free to contact our customer service team. We can help you choose the best replacement part for your bleachers, whether it be the 2½" Aluminum Bleacher Clip or another product.

FLUFF-CORD STRIP TILE

A close-nap carpet-like surface of specially processed rubber-fabric strips made from recycled heavy-duty truck and bus tires; Natural Earthtone Gray Color. Strips are heat bonded to a woven flexible backing. This creates a "dry-back" adhesive back that reacts with our non-flammable adhesive to form a stronger bond to the floor. Install this permanent entry floor mat inside or outside; cord strips act as a wiper where dirt or moisture is a problem; are non-skid, non-absorbing, resist shrinkage, deaden sound. Ideal for heavy wear areas in shopping centers, lobbies, entryways, ramps, airports, etc. Produced in standard 12" x 12" tile size.

Tile must be installed using manufacturer's specific installation instructions and Musson No. TT-390 Non-Flammable Environmentally Safe Adhesive.

Order Fluff-Cord Strip Tiles here

The Interkal Bleacher Drive Wheel is also known as 216008 or Part # P2000VI.

The Interkal Drive Wheel for Bleachers is also compatible with Vectra bleachers. With a 6" diameter x 2-7/16" width x 1" axle, it is set to suit your specific bleacher needs. The Interkal Bleacher Drive Wheel comes with a key ring for your convenience, making maintenance and replacement easy. The wheel is designed to offer durability and efficiency. Interkal Bleacher Drive Wheels are ideal for moving bleachers smoothly and safely, making them perfect for sporting events, school activities and other gatherings.

The Interkal Drive Wheel for Bleachers is made from high-quality materials that resist wear and tear, ensuring it will last through many seasons of use. Its smooth rolling action minimizes strain on the bleachers, helping to preserve its structure over time. With a robust construction, Interkal Bleacher Drive Wheels can handle heavy loads while still being easy to install. The 6" diameter ensures they perform well on a variety of surfaces, and the 1" axle allows them to be easily attached to your existing bleachers. This makes it possible to spend less time maintaining your bleachers and more time enjoying the events you host! Plus, the compact size of Interkal Bleacher Drive Wheels means they won’t take up much space when not in use, making storage easy and convenient. Whether you are a school, sports club or event organizer, the Interkal Bleacher Drive Wheel offers the reliability and functionality you need.

Don’t let cumbersome bleachers hold you back from hosting successful events. Replace or install the Interkal Bleacher Drive Wheel today and experience the difference in mobility and safety. For special inquiries regarding the Interkal Drive Wheel for Bleachers, our customer service team is ready to assist you. Make your next event a breeze with Interkal Bleacher Drive Wheels!

The Hussey Bleacher Wheel ⅜" Axle x 1" Tread x 4" Diameter is also known as 10011132 or Part # P2080HS.

The ⅜" axle x 1" tread x 4" diameter wheel is also compatible with Folding Bleacher Company products.

The Hussey Bleacher Wheel ⅜" Axle x 1" Tread x 4" Diameter is a durable and reliable option for bleacher seating systems. With a load capacity of approximately 125-140 pounds, the ⅜" Axle x 1" Tread x 4" Diameter Wheel for Folding Bleacher Company holds strong in tough conditions. Its hefty construction allows it to withstand a significant load, making it ideal for use in sports facilities, schools, and other event venues. The ⅜-inch axle allows for easy installation and compatibility with a variety of bleacher types.

The ⅜" Axle x 1" Tread x 4" Diameter Wheel for Folding Bleacher Company is designed to ensure smooth and safe movement of your bleachers. In addition, the 1-inch tread is wide enough to provide stability, while the 4-inch diameter provides a high rolling capacity. This makes moving your bleachers easy, even on uneven surfaces.

Maintenance is minimal on the⅜" Axle x 1" Tread x 4" Diameter Wheel for Folding Bleacher Company, which contributes to its longevity and reliability. Whether you need a new set or are looking for a replacement wheel, the Hussey Bleacher Wheel ⅜" Axle x 1" Tread x 4" Diameter is an excellent choice. With its sturdy design and high load capacity, you can be confident that your bleachers will move safely and efficiently.

If you are unsure about which parts you need or how to perform maintenance on the ⅜" Axle x 1" Tread x 4" Diameter Wheel for Folding Bleacher Company, our knowledgeable customer service team is here to help. We can provide guidance on installation and troubleshooting, ensuring you have the support you need to keep your bleachers functioning optimally. Please let us know if you would like more information about the Hussey Bleacher Wheel ⅜" Axle x 1" Tread x 4" Diameter before placing your order. We are always happy to assist!

Stainless Steel unit Tumbler lock, sheet metal and heavy duty piano hinge width 11"w x 15"h x 4"d.
Dispenses 400 C-fold or 525 multi-fold paper towels without adjustment or adapters. Fabricated of 22 gauge stainless steel with #4 satin finish. Fitted with tumbler lock and heavy duty stainless steel piano hinge.

The Von Duprin 98/99 Maintenance Kit includes all the parts and pieces you need to keep your 98 or 99 device running properly for years.  If you are interested we can email a list of the parts.

Von Duprin part # 050046

98/99 Maintenance Kit Instruction Manual