Search results for: 'bolt door lockers cast with degre'

Restroom Door Kit Outswing 7/8" Door & 1-1/4" Post Cast stainless steel. All hardware screws included for installation of these products. All hardware is a gravity close so your door self closing every time. Also known as part number 27813.

18" Quarter Dome 90 Degree Mirror, 1/4 dome, 18" diameter, Covers up to 50 square feet.

1714mkada Master Lock

• 5-Pin Tumble key
  
• Built in key locks, Bolt moves Horizontally.
  
• Comes with 2 user keys.
  
• Automatic locking springbolt.
  
• For box lockers
  
• Right or Left Hinged
  
• Master Keys extra, We will need your master key number if adding to your existing system.
• 1-2 week lead time

18" Full Dome 360 Degree Mirror, Light weight and virtually unbreakable. Covers areas up to 300 square feet. 

Lyon Metal Locker Door Jamb. Used in February 1980 - September 2004, also known as 6726, 75014, ly2234, ll1778. Manufactured in the usa.

Lyon Metal Locker Door Jamb, November 1958 - February 1980. Also known as 6725. Left hand shown in picture.

Restroom Door Kit Inswing 7/8" Door & 1-1/4" Post Cast SS. All hardware screws included for installation of these products. All hardware is a gravity close so your door self closing every time. Also known as part number 17803.

Aluminum Store Front Door Flush Bolt FB-1202

15/16" x 4-1/4" radius face, 5-7/32" hole spacing, 1/8" offset, 5/8" throw, 12" rod length, with a square nylon tip with beveled corners fits in a 1/2" square hole.

1714 Master Lock

• 5-Pin Tumble key
  
• Built in key locks, Bolt moves Horizontally.
  
• Comes with 2 user keys.
  
• Automatic locking springbolt.
  
• For box lockers
  
• Right or Left Hinged
  
• Master Keys extra, We will need your master key number if adding to your existing system.
  1-2 week lead time

Friction Ring Insert For 90 Degree Inside Corner caster. For 7/16" diameter casters only.

Interior Steel Box Locker Door Pull, Hole spacing 2-3/16" between outer holes. Used November 1958 - Current, also known as 6719.

Friction Ring Insert For 90 Degree Outside Corner. For use with 7/16" diameter casters ONLY. 

• Available (NHO) non-hold open,
(SHO) selective
hold open. Specify degree (90, or
105°)
• Standard top pivot: 180 included
• Cycolac cement case
• Separate independent valves for closing,
latch and backcheck adjustments
• Built-in positive dead stop prevents door
from swinging beyond the desired
opening degree
• Vertical door adjustment

Less all parts means, only the Cylinder!

Lyon Metal Locker Two Person Upper Door Jamb, April 953 - August 1970. Also known as 6755, 75037, ly2213, ll1790..

FEATURES

• Please note the factory will only sell in quantities of 10.
• Large, all-steel ADA Compliant User Paddle Key for ease of access
• Ergonomic dial with grip ring and non-slip coating
• 7 pre-set combinations for extended usage
• Supervisory key control
• Includes 2 User Keys
• Nut channels for easy installation
• 3-digit dialing combination with 5-pin tumbler key plug
• All Built-in Combo Locks have a 10 year warranty from time of shipment
• 72 hour shipping available    

APPLICATIONS

• For higher security; recommended for ventilated lockers
• Fits all traditional locker styles
• Model 1971ADA is for use with locker door hinged on left
  

Toilet Partition Bottom Hinge Assembly For 7/8" Door To 1-1/4" Pilaster Square Edge Cast Stainless Steel

Cast stainless steel hinge. Hinge mounts to 1-1/4" square edge post or pilaster, for use with 7/8" thick doors. Kit includes bottom hinge, pintle, pin and insert. Also known as a Bathroom Stall Bottom Pivot Hinge Set. Manufacture part # 63013

Includes all screws.

Cast stainless steel outswing door kit for square edge doors and posts. For 1" doors and 1-1/4" post. All hardware screws included for installation of these products. All hardware is a gravity close so your door self closing every time. Also known as part number 21003.

Partition Door Pull 3-1/2" Between Screws Cast Stainless Steel

Cast stainless steel construction. The pull measures 4-3/4" wide and projects 1" with a hole spacing of 3-1/2". The mounting holes are threaded for a 10-24 screw. Also known as a Bathroom Stall Door Pull. Manufacture part # 5403.

Surface Mounted Partition Slide Bolt Latch Stainless Steel 3/8" Bar To Door Clearance

Cast stainless steel construction. Latch base is 4-1/2" high with 3-1/2" hole spacing. Latch bolt is 3-3/32" long by 1" wide by 3/16" thick. The latch bolt clearance is 5/16" from the back of the base to the under side of the latch bolt and projects out 15/16". The latch projects out 1-9/16" from the face of the door when installed. Also known as a Bathroom Stall Surface Mounted Slide Bolt Latch and Toilet Partition Locks. Manufacture part # 5063.

Shipped with mounting screws.

Toilet Partition Stainless Steel Continuous Hinge, 71", Non-Handed, 14 Gauge, 1/4" Pin

Stainless Steel Construction 14 gauge (.075" thick). Hinge is 3" wide when laid flat, by 71" long. Holes are typically spaced every 14". The hinge pin is 1/4" diameter, and the mounting holes are 9/32" diameter. This hinge is also known as a Full Length Toilet Partition Continuous Hinge. Hinge had rounded edge 3/8" radius and is cam (gavity) self closing. Designed to be zero degree hold so that door will close flush with partition surface. The Bathroom Stall hinge can be raised up 3/8" for emergency entry.

*Fasteners not Included *

Manufacture part # 160799

FEATURES

• Please note the factory will only sell in quantities of 10.
• Supervisory key control
• Ergonomic dial with grip ring and non-slip coating
• 7 pre-set combinations for extended usage
• 3-digit dialing combination with 5-pin tumbler key plug
• Patent pending button guard to protect lock function from overstuffed lockers
• Nut channels for easy installation
• All Built-in Combo Locks have a 10 year warranty from time of shipment
• 72 hour shipping available

APPLICATIONS

• Model 1971 is for use with locker door hinged on left; similar in operation to Master Lock 1671
• For higher security; recommended for ventilated lockers
• Fits all traditional locker styles

FEATURES

• Please note the factory will only sell in quantities of 10.
• Large, all-steel ADA Compliant User Paddle Key for ease of access 
  
• Ergonomic dial with grip ring and non-slip coating
• 7 pre-set combinations for extended usage
• Supervisory key control
• Automatic locking
• Includes 2 User Keys
• Nut channels for easy installation
• 3-digit dialing combination with 5-pin tumbler key plug
• All Built-in Combo Locks have a 10 year warranty from time of shipment
• 72 hour shipping available

APPLICATIONS

• Fits all lift handle gravity latch, multi-point lockers
• Model 1930ADA is for use with locker door hinged on right

Door Finger Protector - Exterior Push Side

This model is specifically designed for exterior doors on the push side of the door. This patented Finger-Gard product is designed for both exterior and interior doors and thus will operator in very cold and very hot tempetures. Flexible to minus 40 degrees. They are made of a special rubber that is resistant to harsh sunlight. They will allow the door to swing up to 180 degrees. This product is available in Brown or White, 78" or 83" lenghts

Our part # on this is GFG5 for the 78" length, and GFG5+ for the 83" length.

Multi-User Built-In Locks. Best Used For: Health & Recreation Facility Lockers School, Employee, & Athletic Lockers Product Features: Allows a locker user to set their own temporary 3-digit combination for the duration of visit, eliminating the need for system charting Designed for standard, lift handle lockers with hinges on the right Manual spring locking Solid zinc housing provides durability for multiple uses on a daily basis Secure, easy to use resettable combination lock offers up to 1,000 different combinations Control key for supervisory access; specify key to match existing system or factory assigned Extension kit available for use on wooden doors with a thickness of 11/16" to 3/4". Known as 3670.

Partition Keeper Bumper Inswing 1-1/4" Post Square Edge Cast Stainless Steel

Cast stainless steel construction. The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. The latch bolt slot is 1-9/16" high by 5/16" deep. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for inswinging doors. Also known as a Bathroom Stall Strike and Keeper-Inswing 1-1/4". Manufacture part # 5113.

Shipped with mounting screws.

 FEATURES

• Please note the factory will only sell in quantities of 10.
• Supervisory key control
• Ergonomic dial with grip ring and non-slip coating
• Automatic locking
• 7 pre-set combinations for extended usage
• 3-digit dialing combination with 5-pin tumbler key plug
• Patent pending button guard to protect lock function from overstuffed lockers
• Nut channels for easy installation
• All Built-in Combo Locks have a 10 year warranty from time of shipment
• 72 hour shipping available

APPLICATIONS

• Fits all lift handle gravity latch, multi-point lockers
• Model 1930 is for use with locker door hinged on right; similar in operation to Master Lock 1630

Multi-User Built-In Locks. Best Used For: Health & Recreation Facility Lockers School, Employee, & Athletic Lockers Product Features: Allows a locker user to set their own temporary 3-digit combination for the duration of visit, eliminating the need for system charting Designed for standard, lift handle lockers with hinges on the right Manual spring locking Solid zinc housing provides durability for multiple uses on a daily basis Secure, easy to use resettable combination lock offers up to 1,000 different combinations Control key for supervisory access; specify key to match existing system or factory assigned Extension kit available for use on wooden doors with a thickness of 11/16" to 3/4". Known as 3631.

Multi-User Built-In Locks. Best Used For: Health & Recreation Facility Lockers School, Employee, & Athletic Lockers Product Features: Allows a locker user to set their own temporary 3-digit combination for the duration of visit, eliminating the need for system charting Designed for standard, lift handle lockers with hinges on the right Manual spring locking Solid zinc housing provides durability for multiple uses on a daily basis Secure, easy to use resettable combination lock offers up to 1,000 different combinations Control key for supervisory access; specify key to match existing system or factory assigned Extension kit available for use on wooden doors with a thickness of 11/16" to 3/4". Known as 3630.

Toilet Partition Top Hinge Assembly For 7/8" Door To 1-1/4" Post Square Edge Cast Stainless Steel

Cast stainless steel hinge. Hinge mounts to 1-1/4" square edge post or pilaster, for use with 7/8" thick doors. Kit includes top hinges, pintle, pin and inserts. Also known as a Bathroom Stall Top Pivot Hinge Set. Manufacture part # 63023

Includes all screws.

Concealed Latch Fix it Kits for Powder Coated Steel

For 1" Thick Doors- Round Edge for Powder Coated Steel
All Hardware included

FEATURES

• Please note the factory will only sell in quantities of 10.
• Supervisory key control
• Ergonomic dial with grip ring and non-slip coating
• Automatic locking
• 7 pre-set combinations for extended usage
• 3-digit dialing combination with 5-pin tumbler key plug
• Patent pending button guard to protect lock function from overstuffed lockers
• Nut channels for easy installation
• All Built-in Combo Locks have a 10 year warranty from time of shipment
• 72 hour shipping available

APPLICATIONS

• Fits all lift handle gravity latch, multi-point lockers
• Model 1931 is for use with locker door hinged on left; similar in operation to Master Lock 1631

FEATURES

• Please note the factory will only sell in quantities of 10.
• Large, all-steel ADA Compliant User Paddle Key for ease of access
• Ergonomic dial with grip ring and non-slip coating
• 7 pre-set combinations for extended usage
• Supervisory key control
• Includes 2 User Keys
• Nut channels for easy installation
• 3-digit dialing combination with 5-pin tumbler key plug
• All Built-in Combo Locks have a 10 year warranty from time of shipment
• 72 hour shipping available    

APPLICATIONS

• For higher security; recommended for ventilated lockers
• Fits all traditional locker styles
• Model 1970ADA is for use with locker door hinged on right
  

FEATURES

• Please note the factory will only sell in quantities of 10.
• Large, all-steel ADA Compliant User Paddle Key for ease of access 
  
• Ergonomic dial with grip ring and non-slip coating
• 7 pre-set combinations for extended usage
• Supervisory key control
• Automatic locking
• Includes 2 User Keys
• Nut channels for easy installation
• 3-digit dialing combination with 5-pin tumbler key plug
• All Built-in Combo Locks have a 10 year warranty from time of shipment
• 72 hour shipping available

APPLICATIONS

• Fits all lift handle gravity latch, multi-point lockers
• For use with locker door hinged on left

Toilet Partition Continuous Hinge 54" With Cam Close Stainless Steel. The hinges must be mounted flat when door is shut. For inside swing the hinges are mounted on the inside of the stall. For the outside they must be mounted on the outside.

Stainless Steel Construction, 14 gauge (.075" thick). Hinge is 3" wide when laid flat, by 54" long. Holes are spaced every 13" and are 9/32" diameter and 5 sets of holes. The hinge is self closing by a cam action, which is made possible by angle cuts on the continuous hinge leafs. Cam features Zero Degree Closing. Can be raised up 3/8" for emergency entry. This hinge is also known as a Bathroom Stall Full Length Continuous Hinge. This hinge is non handed. Manufacture part # 130209, 7599, 125319, 650-9402. This hinge is known as 7599.