Search results for: 'grai 8 dyad brook door handed'

Black Round Plastic Chair Tips for Round Tubing chair legs with a 3/4" Oustside Diameter X 5/8" Inside Diameter. Available in black only. 

Global Partitions Top Hinge Pin

Zinc plated steel construction. The hinge pin is 3/8" diameter by 3-3/4" long. Also known as a Bathroom Stall Door Hinge Pin. Manufacture part # 98544.

Bobrick B-369 recessed paper towel dispenser and waste receptacle in a satin finish stainless steel. Seamless beveled flange. Dispenses 350 c-fold or 400 multifold towels. knob latch retains door. Removable waste container has a 2 gal. capacity. Rough wall opening 12-5/8"w x 26-5/8"ht x 4" minimum depth.

Corbin Russwin ED4200 Active Head

Used on the Corbin Russwin ED4000 Rim Devices, for non fire rated doors. A non fire rated door is a door were you can use your allen wrench to dog, or lock, the door in the open position during business hours.

Corbin Russwin part # 650F37-8

The Hub Position for the ED4200

Framed Mirror 20 Gauge, #8 Polished Stainless Steel Front Mount. Frame 14 Gauge type 304 stainless steel finish. All corners are welded and ground to smooth finish. Front mounting furnished with Torx head vandal-resistant 1/4-20x2(150mm) machine screws. Designed in mind for Behavioral Health and Detention Centers.

Dimensions

12″ x 16″ x 5⁄8″ (305 x 406 x 16 mm)

Grade 1 Exit Device
Device is non handed
Standard sizes are 30", 36", 42" or 48"
Minimum stile width is 2"

Replacement parts are also available

The Detex V40xNS is designed for Narrow Stile Doors with a stile width of at least 2". The 36 inch is 34-7/8 inches wide overall, and the 48 inch device is 46-7/8 overall.

Partition U Bracket For 3/4" Thick Panel Cast Stainless Steel. Cast stainless steel construction. Bracket base is 1-3/8" x 1" with two mounting screw holes. Bracket legs project out 1-3/8" with the thru hole at 1" on center from the bottom of the base. Also known as a Bathroom Partition Stall U-Bracket or Wall Bracket 3/4". Manufacture part number 1893. Shipped with mounting screws.

Square Chair Turing Metal Swivel Glide with a Square Tubing measurement of 7/8" O.D. X 3/4" I.D. This metal swivel glide has a 1 1/6" base diameter and also has a ferrule. 

American Sanitary Partitions Top Hinge Pin

Zinc plated steel construction. The hinge pin is 3/8" diameter by 3-3/4" long. Also known as a Bathroom Stall Door Hinge Pin. Manufacture part # 98544.

Dor-o-matic 1790 Center Case Cover Screw

For devices shipped before September, 2004

Doromatic part # SCREW.1025 or PB324

Dor-o-Matic 1790 Repair Parts Breakdown

Truth Telescoping Pole

Telescoping Pole with Hex Ball or Hook Drive
Rigid anodized aluminum poles feature free-turning ABS hand grips.
6 foot pole extends to 10 feet.

Truth Part # 10637 Hex Drive
Truth Part # 10638 Hook Drive

Von Duprin 5547 Top Rod Kit

Von Duprin 050053 5547 Top Rod Kit for doors 6'8" to 8' tall.

Von Duprin Part # 050053
Old Von Duprin Part # 104759

Threaded spring clip for round legs. 1/4-20 thread for use with our LA10625 and SLA12525. 5/8" outside diameter, 1/2" inside diameter with a 1/4-20 thread. This clip has an outside holding clip. 

The ESC6600 are non handed, with a Grade 1 thru bolted design. It features a clutch mechanism, double heavy duty spring support to prevent sagging and a hardened stell heavy duty spindle. Entrance function, key locks or unlocks lever, operates as a Classroom Function. Ships with mounting screws and a 6-Pin Schlage Mortise Cylinder. 

If your toilet partition (bathroom stall) wall bracket is stamped 1630, then chances are you have the Two Ear Wall Bracket for 7/8″ thick toilet partition panels. This brackets base is 1-3/8″ wide x 3-1/2″ long with 2-3/4″ center to center hole spacing. The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. The bracket is made of a die cast material that is then chrome plated. The bracket sometimes goes by the name Bathroom Stall (toilet partition) Two Ear Bracket or Wall Bracket.

Torque Head Barrel Nut Shoulder Screw for 7/8" - 1-3/16" gripping. Use with torque driver bit T27 for toilet partition security screws. 10-24 thread chrome plated and uses a 6 lobe  head torque. Both pieces included.

Corbin Russwin Hold Open Arm

Friction hold open arm.

Corbin Russwin part # 688F77

Napkin Disposal w/o Shelf Stainless Steel Surface mount 16 gauge utility shelf. Overall Size 7 1/2" x 10" x 3 7/8".  Surface Mounted Sanitary Napkin Disposal shall have top cover door and cabinet of 22 gauge type 304 stainless steel alloy 18-8. All exposed surfaces shall be satin finish and be protected during shipment with PVC film easily removable after installation. Capacity shall be 1.2 gal (4.5L). Top cover is attached to cabinet with a full length 3/16" diameter (Ø4.8) stainless steel multi-staked piano hinge. Structural assembly of body and door components shall be of welded construction. American Specialties 0852 stainless steel napkin disposal unit.

The International 8000 Series End Cap is used on the hinge side of the the exit device.  This cap includes the mounting bracket and the mounting screws.   It is constructed of a die cast metal for years of service.  The piece measures 2-3/8" by 2-1/4" by 1-1/2".  This end cap is used on the International Door Closer models, 8510S, 8610S, 8710S, 8810S, 8620S, 8530S, and 8650S devices, along with the same devices ending in F.    

Penco Recess Locker Lift with Trigger in 028 Grey color. This is for a Right Handed Locker Facing it with the hinges on the right side. (Handle on the Left Side). Also known as 608930c.

Standard duty 2-1/4" knob is factory pinned to swivel spindle
to 1-3/4" door. Spindle has two 3/8" centers. Inside knob has
two case hardened set screws and spindle is threaded 3/8-18

Truth 16.52 Sash Lock. A very common sash lock that tends to fail because the plastic slide breaks due to incorrect installation at the window manufacturer or being forced when there is a obstruction in the window opening. The new replacement model has a thicker plastic slide. Because the slide is thicker, the keeper, part # Wi41268 and Wi41269 might have to be shimmed with small washers.

Common numbers found on this sash lock are 21328 and 45189

Non handed (can be used on right or left hand windows).

FLUFF-CORD STRIP TILE-CONTINUOUS STRIP

A close-nap carpet-like surface of specially processed rubber-fabric strips made from recycled heavy-duty truck and bus tires; Natural Earthtone Gray Color. Strips are heat bonded to a woven flexible backing. This creates a "dry-back" adhesive back that reacts with our non-flammable adhesive to form a stronger bond to the floor. Install this permanent entry floor mat inside or outside; cord strips act as a wiper where dirt or moisture is a problem; are non-skid, non-absorbing, resist shrinkage, deaden sound. Ideal for heavy wear areas in shopping centers, lobbies, entryways, ramps, airports, etc. Produced in longitudinal rolls 12" wide x 25' long.

Tile must be installed using manufacturer's specific installation instructions and Musson No. TT-390 Non-Flammable Environmentally Safe Adhesive.

Order Fluff-Cord Strip Rolls here

If your toilet partition or bathroom stall wall bracket is cast with the number 1940 on the back, then you have the “U” Wall Bracket for 1-1/4″ thick toilet partition panels. The wall bracket is usually mounted on the wall or the pilaster to mount the toilet partition stall panels. This bracket is 1-1/2″ wide x 1-3/8″ tall, with the through hole located at 1″ from the back. If features 4 holes with a 1/4″ diameter, with two of them on the base. The bracket is made of a die cast material that is then polished chrome plated. This bracket is sometimes called a Toilet Partition or Bathroom Stall “U” Bracket, or “U” Wall Bracket.

The Monarch 712L Lever Trim is used for the XX-C, 18-C, and all 24 Series Falcon Devices.  The XX-C and 18-C are the obsolete concealed vertical rod Monarch Exit Devices. The Trim is non handed or field reversible. The Key locks or unlocks the Lever.  The escutcheon measures 1-3/4" wide and 7-1/4" long.

Torque Head Barrel Nut Shoulder Screw for 1-1/4" - 1-5/8" gripping. Use with torque driver bit T27 for toilet partition security screws. 10-24 thread chrome plated and uses a 6 lobe  head torque. Both pieces included.

The Doromatic 1790 rim device is typically used in applications where maintenance is a concern because the rim device has fewer parts and pieces than current exit devices. The result is less maintenance and adjustment. The streamlined design has no openings for chains, reducing the risk for code infringements and offering increased building security by eliminating the possibility of tampering and forced entry through the use of coat hangers and other tools. The Doromatic 1790 may also be used to retrofit a Doromatic 2090 series crossbar device.

Replacement parts are also available

Shipped with all screws and strikes. If you wish to use a key cylinder on the exterior, you will need the 1790 NL/HB Cylinder Assembly, 179CA.

Truth 14.17 Casement Hinge-Pair

The 14.17 is not that popular of a hinge. But if your track measures 14" than this is probably what you have. The hinge has a stack height of 7/16". The outside screw holes measure 12-3/8" on center. We sometimes find the number 30986 on the arm and 41498 and 41499 on the stainless steel track.

This hinge is sold in pairs (one top and one bottom). If your window is the opposite hand, the top hinge goes to the bottom and the bottom hinge goes to the top.

Doromatic Exit Device 2090 Lever Arm

Right hand dark brown shown in picture

Dor-o-Matic 1090/2090 Repair Parts Breakdown

Metal based Swivel Glide for round tubing. Measurements of the chair leg are  5/8" O.D. X 1/2" I.D. This glide comes with Ferrule. Used by Peabody and other manufacturers. Base of the glide is 1 1/4" metal.  Swivel glide, grips inside of leg, see "More View" for picture of clip.  Metal base glides are very popular in schools and institutions and move easily across smooth or carpeted floors.  Metal base glides are nickel plated and are extremely durable, but when they do wear out, they will scratch the floor.  The glide freely swivels beyond 30 degree angle. Glide grips leg with outside holding clip, meaning it grabs the outside of the leg, see more views for picture of outside holding clip. 

Back to Back mounted 1 inch diameter stock.  One handle will be threaded and the other will be a female fitting that snugs the handle with a set screw.  The standard Stud that ships with the handle is for an 1-3/4 thick door.

Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.

Flush Metal Partitions Pintle 5/8" Diameter For Steel Doors

Steel and white nylon construction. The Pintle is 5/8" diameter by 2-1/4" overall length with 5/16-18 threaded end. Also known as a Bathroom Stall Bottom Pintle 5/8" Medium Lift. Manufacture part # 98175.

Shipped with nut and lock washer.

Metal Swivel Chair Glide for a chair leg with a  3/4" O.D. X 5/8" I.D. This Swivel base chair glide features a Ferrule and Nylon Base. The base of this chair glide is 1 1/4" in diameter. Metal base glides are very popular in schools and institutions and move easily across smooth or carpeted floors.  Metal base glides are nickel plated and are extremely durable, but when they do wear out, they will scratch the floor.  The glide freely swivels beyond 30 degree angle. Glide grips leg with outside holding clip, meaning it grabs the out side of the leg, see more views for picture of outside holding clip.