Search results for: 'casemelong handlnt truth handle 2 3/8'

The GS520S Rubber Stair Tread with grit stripping has a 1/4" nose thickness which tapers down to 1/8" at the back.  The nose drops down 1-9/16", and the nose is not adjustable and is not tapered. You have two choices on the Grit Stripping, the Visual Impaired 1-2" wide or 2-3/4" wide grit tape strips. They are designed for interior use.

Nylon based Metal Swivel Glide for a round chair leg with a 1-1/8" O.D. X 1" I.D. This glide does not have a ferrule. This glides base is 1 1/4" in diameter. Metal Furniture Feet for school and institution applications. Nylon base protects your floor as long as the bottom does not have grit and grime on it. 

Single Piece Mirror, type 304 stainless steel formed mirror #8 mirror polished finish. Fabricated with Rounded corners, integral frame and 6 dimpled mounting holes. Front mount with Torx screws included. Designed in mind for Behavioral Health and Detention Centers.

Dimension

12” x 16” x 1/4” (305 x 406 x 6 mm)

Mirror Gauge

107-14 (20 Gauge)

Monarch Exit Device 914KIL Lever Trim

The 914KIL Lever Trim is for use on the Monarch / Falcon 19 Series.  This lever trim is shipped with a standard Schlage C Keyway, that are keyed different if you are ordering multiple levers.  The key locks and unlocks the Lever handle.

Monarch Falcon Part # 914KIL-KD

Used on chairs and table, so you can use an adjustable height gilde. Used with the LA10625 or SLA12525. 1/4-20 Thread, 1" outside diameter and 7/8" inside diameter.

Safeglides-Brown 1 1/2" Base Diameter Nail On Glide for furniture. To install the glide, tap it into your wooden furniture.

Bleacher Bolt Fastener Kep Nut 3/16-24.

Partition Door Integral Hinge Set Top & Bottom. The bottom pin is 4-7/8" high & the top pin 3" X 1/2" high. Most manufactures used this integral hinge pin set for solid plastic partitions. The Pilasters next to the door are cut out for this door to fit in it. The hinge pins break often due to swinging on the door which causes the pin to bend and breaks the door. Manufacture part #7005.

Bleacher Bolt Fastener Type D-1" Head, 5/16-18 X 1-3/4" Long.

Flush Metal Partitions Keeper Bumper For 1-1/4" Outswing Square Edge Pilaster Or Post

The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for outswinging doors. Also known as a Bathroom Stall Strike and Keeper-Outswing 1-1/4". Manufacture part # 5210 Shipped with mounting screws.

The Swivel Glide 5/8" Outside Diameter with Ferrule Outside Holding Clip is used on American Desk, Artco Bell, Carter Craft, Krueger, Peabody and Virco Chairs. Metal base glides are very popular in schools and institutions and move easily across smooth or carpeted floors.  Metal base glides are nickel plated and are extremely durable, but when they do wear out, they will scratch the floor.  The glide freely swivels beyond 30 degree angle. Glide grips leg with outside holding clip, meaning it grabs the out side of the leg, see more views for picture of outside holding clip.  This product will git all 5/8" outside diameter tubing.  The base has an 1-1/4".

Bottom Partition Hinge For 1-1/4" Round Edge Post Or Pilaster

Chrome plated Zamac die cast construction. The hinge measures 1-1/4" deep by 2-1/8" high by 1-7/16" wide. The U part of the hinge measures 2-1/8" high by 1-1/4" deep with a slot depth of 11/16". The hole spacing is 1-1/2". The lug projects out 1-3/32" and is 1/2" thick with a 5/16" diameter hole. Also known as a Bathrrom Stall Pivot Hinge - Bottom 1-1/4". Manufacture part # 4040. Used on Ampco and Metpar Metal Partitions.

Shipped with mounting screws.

A=1-7/16"

Von Duprin 33/3547 99/9947 Ratchet Lever Spring (2)

One of two springs located in the 33/3547 and 98/9947 Top Latch 050492.  Sold in packages of 2.

Von Duprin Part # 090069

Toilet Partition Bottom Hinge Assembly For 7/8" Door To 1-1/4" Pilaster Square Edge Cast Stainless Steel

Cast stainless steel hinge. Hinge mounts to 1-1/4" square edge post or pilaster, for use with 7/8" thick doors. Kit includes bottom hinge, pintle, pin and insert. Also known as a Bathroom Stall Bottom Pivot Hinge Set. Manufacture part # 63013

Includes all screws.

Chrome plated Zamac die casting construction. Coat hook bumper projects out 3" and has a rubber insert. The hook projects out 1-7/32". The coat hook bumper base is 1-7/16" wide by 2-1/4" high with a hole spacing of 7/8". Also known as a Bathroom Stall Hook. Manufacture part # 4000.

Toilet Partition Pilaster Anchoring Device

Zinc plated steel construction. For 3/4" thick and larger Pilaster Posts and 3" wide and larger pilaster posts. The brackets are 11/16" wide. Also known as a Bathroom Stall Pilaster Post Anchoring Pack. All the screws are included in the package.

Medart Bleacher Rear Shoulder Pin 3/4", for front row truck assembly.

Bleacher Bolt Fastener Type G - 5/16-18 X 1 1/2" Long.

Sanymetal Coat Hook Bumper 3" Projection

Chrome plated Zamac die cast construction. The coat hook base measures 2" by 1-11/16" with a 1-1/8" hole spacing. The hook projects out 1-13/16". The bumper projects out 3" with a rubber insert on the tip. Also known as a Bathroom Stall Hook. Manufacture part # 4280.

Shipped with mounting screws.

Lyon Metal Locker double tier lock bar, 27-1/2" in length. Used Feb 1980 - Sept 1981.
2 Wire Springs included. Also known as 6776.

Toilet Partition Continuous Alcove "H" Bracket For 1" Panel x 54" Long Stamped Stainless Steel

18 gauge (.05" thick) stamped stainless steel construction. Bracket is 1" x 3-1/2" x 54" long. Legs project out 1-3/4" with the thru hole at 1-3/8" from the base. Mounting and thru bolts every 13" or so. Also known as a Bathroom Stall Alcove Bracket or "H" Bracket. Manufacturer part # 2859.

Shipped with screws.

Permanent in ground Mount Aluminum Bench with out backrest with Galvanized Steel Legs. Available sizes are 6', 8' and 12' benches. All Hardware included, 2" x 10" anodized seat planks, 2-3/8" galvanized pipe leg design. Note 12' benches will ship by truck.

Call for Pricing********

Lyon Metal Locker single tier lock bar, 56-1/2" in length. Used Feb 1980 - Sept 1981.
3 Wire Springs included. Also known as 6775.

Concealed Latch Keeper Bumper Outswing Cast Stainless Steel

Cast Stainless Steel casting. The strike and keeper is 1-1/4" high by 1-3/4" deep by 1/8" thick. The stop is 1/2" deep by 1-1/4 wide with a rubber insert. Also known as a Bathroom Stall Strike and Keeper Outswing Flat. Manufacture part # 5643.

Shipped with mounting screws.

Black Plastic Chair Tips for  Round Tubing with a chair leg 7/8" Outside Diameter X 13/16" Inside Diameter. Available in Black. 

1714 Master Lock

• 5-Pin Tumble key
  
• Built in key locks, Bolt moves Horizontally.
  
• Comes with 2 user keys.
  
• Automatic locking springbolt.
  
• For box lockers
  
• Right or Left Hinged
  
• Master Keys extra, We will need your master key number if adding to your existing system.
  1-2 week lead time

LCN Door Closer 4050 Rw/PA

This new LCN Door Closer is a direct replacement for the Norton 7500 and Yale 4400 Door Closers.  It features, a cast aluminum cylinder, 2-3/8” x 6-3/4” hole spacing, 25 year warranty, powder coated finishes, and stick on mounting template.  This door closer comes with the ability to mount on the push, pull or top jamb and is non handed.   The door closer meets Grade 1-ANSI A156.4, UL/cUL, ADA and the Buy American Act certifications.

General Toilet Partitions Keeper Bumper For 1-1/4" Outswing Square Edge Pilaster Or Post

Zamac die casting that is polished chrome plated. The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for outswinging doors. Also known as a Bathroom Stall Strike and Keeper-Outswing 1-1/4". Manufacture part # 5210

Shipped with mounting screws.

Zamac die casting that is polished chrome plated. The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. The latch bolt slot is 1-9/16" high by 5/16" deep. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for inswinging doors. Also known as a Bathroom Stall Strike and Keeper-Inswing 1-1/4" Square Edge. Manufacture part # 5110. Shipped with mounting screws.

B-2890 Bobrick single jumbo toilet tissue dispenser. The unit is a satin finish stainless steel. Equipped with a keyed lock. The spindle holds up to one 10" diameter roll and for a 3" diameter core. Stainless steel mounting plate and is 10-21/32"w x 10-5/8"h x 4-1/2"depth.

Yale 50 Series Door Closer

• ANSI A156.4, Grade 1
• 10-year warranty
• Non-handed
• Rack-and-pinion design
• Cast aluminum body
• 1-3/8" (35mm) diameter piston
• 5/8" (16mm) diameter pinion journals
• Standard, separate and independent, latch, sweep
  and backcheck intensity valves
• 2-7/8" (73mm) projection
• Tri-Packed- packed for regular arm, top jamb and
  parallel arm installations.
• All standard arm applications allow

Older models may be stamped with Scoville or Eaton, which are the companies that used to own Norton
We some times find 20-0054-4001 or 20-0254-4001 stamped on the back of the closer

Toilet Partition Pilaster Anchor 'L' Bracket For 1-1/8"-1-1/4" Thick Pilaster Posts

Zinc plated brackets and screws. Also known as a Bathroom Stall Pilaster Post Anchoring Pack. Package includes all needed screws and brackets.

1695mkada Master Lock, Built-in lock for ADA single point latch lockers designed for Wrap Around Latch Technology, automatic deadbolt locking, right-hand hinged door, with Master key enabling. Includes 2 student keys with ADA key head. Order Master Key separately.
ADA For Single Point Lockers. Spring latch locks automatically.
RH Only
1-2 week lead time

The Matte Black Hadrian Two Ear Bracket is constructed of stainless steel and measures 3-1/8"Wx1-1/4"Hx47"L. This two ear bracket is designed for 1/2" thickness material. Bracket comes with fasteners to install. Known as manufacturers part number H20559-BLK.

Cal Royal 2200 Escutcheon Lever Trim

2-5/16" X 8-1/2"

Toilet Partition Alcove Clip Set, 2 Pieces, For 1" To 1-1/4" Panel Stainless Steel Plated

These clips are 1-1/2" tall x 2-1/4" wide. The screws are 1-1/2" on center, with 1/4" diameter holes. The clip is constructed of cast stainless steel material. This part is also know as Bathroom Stall Alcove Clip Set, or Toilet Partition Alcove Clip. The manufacturers part number is 8343. These clips are sold in sets with the fasteners. They are used to connect a 1" panel to a 1-1/4" panel.