Search results for: 'gloss 8 drill been door hidden'

The Truth 23.49 is a Dyad Operator is rear mounted. The linkage arm is 9-1/4 inches overall length, 8-3/4 inches hole to hole. The rear mounting holes are 5 inches on centers.

The Truth-Wright Split Arm Operator is a replacement for the older Wright Operators.  Linkage arm has an overall length of 3-5/8".

Left Hand Shown in Picture, we can only get these in white.

Republic Steel upper locking bar for a two person locker RH. 700337 spring and 700338 latch included. 7-5/8" length. Prior to current. Facing the locker the hinges will be on the Right side. Also known as 75703, 2719, 70010, rs1123, lr703.

Adams Rite 22-0430-IP 8700/8800 Strike is used on the rim devices that have the Star Wheel Latching System.  The strike measures 2-3/4" long by 1-3/4" wide and projects out approximately 3/8".

Permanent in ground Mount Aluminum Bench with out backrest with Galvanized Steel Legs. Available sizes are 6', 8' and 12' benches. All Hardware included, 2" x 10" anodized seat planks, 2-3/8" galvanized pipe leg design. Note 12' benches will ship by truck.

Call for Pricing********

Comtec Toilet Partitions Aluminum Slide Bolt Latch 3-1/2" Screws

Clear anodized aluminum construction. Base is 4-1/2" tall by 2" wide by 1/8" thick. Latch bolt is 3-1/8" long by 1" wide by 1/4" thick, and has a 1" throw. The latch bolt is 9/16" from the bottom of the base to the under side of the latch bolt. Also known as a Bathroom Stall Aluminum Slide Bolt Latch and Toilet Partition Locks. This latch is usually used on Solid Plastic (HDPE) Toilet Partitions. The manufacture part #'s are 4988, 650-4051, 650-8543 and HLSLA.

This latch ships with the mounting screws.

Security Front Mount Grab Bar fabricated with 18 gauge, 1-1/2" diameter tubing and flanges are 1/8" (3mm) thick stainless steel type 304 satin finish. The Closure Plate is 1/8" (3mm) thick and is welded the the bottom side of the grab bar. Closure plate is constructed of 12 gauge stainless steel. Unit has 3 holes on each flange for exposed mounting. Each flange is " in diameter Special Closure Plate is designed for Security and Anti-Ligature applications. Designed in mind for Behavioral Health and Detention Centers.

Toilet partition square edge pilaster shoe, stamped stainless steel construction. Pilaster Shoe measures 2" to 24" wide by -3/4" thick by 3" high. This size pilaster post shoe is not split on either end. Also known as a bathroom stall pilaster post shoe square edge. Used for the base of the support system with pilaster mounting.

If your toilet partition (bathroom stall) wall bracket is cast 1840, then you have the One Ear Wall Bracket for 1-1/4″ thick toilet partition panels. This brackets base is 1-3/8″ wide x 2-3/4″ long with 1-1/2″ center to center hole spacing. The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. The bracket is made of a die cast material that is then chrome plated. The bracket sometimes goes by the name Bathroom Stall One Ear Bracket, Toilet Partition One Ear Bracket, Single Leg Bracket or Wall Bracket.

Bobrick Toilet Partition Keeper Bumper For 1" Outswing Square Edge Post

Polished chrome plate Zamac die casting construction. Strike and Keeper measures 2-1/2" high by 1-15/16" wide. Stop is 17/32" thick and projects out 13/16". The screw holes are 1-1/2" on center. This Bathroom Toilet Door Keeper is designed for use on 1" thick square edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Outswing 1". Manufacture part # 5720.

Shipped with mounting screws.

Toilet Partition Nylon Hinge Insert Replacement Kit

Replaces Bathroom Stall hinge pins on our part #'s 9a7043, 9a7043, 9a7ss1, 9a7ss2, 9a07b1 & 9a70b2.

actual size 5/8" x 2-3/4"

Adams Rite Old Style Dogging Pin

This Adams Rite part is a replacement for worn or stripped dogging pins. The older style pins were an 1/8" allen head hex. The replacement is 5/32".

Adams Rite part # 24-0730

Awning Operator Guide Bar 30568

The Truth Operator Guide Bar measures 26-3/4" long with the two mounting holes at 26-1/8" on centers. The bar is constructed of extruded aluminum. The Wi10005 is the component that slides in this track. This track is mounted to the sash.

Truth Part # 30568

Global Concealed Latch Knob & Cover Chrome Plated

Zamac die cast construction with polished chrome plating. Outside diameter of the knob and cover are 1-5/8" with the inner ring diameter of 1-1/4". Also known as a Bathroom Stall Concealed Latch Cover and Knob Assembly. Manufacture part # 1390, 1380, 6140.

The Falcon Doromatic Adjustable Mortise STrike STK70 is used on their mullions.  This is the strike that fits in the tear drop shapped mullion. They measure 2-3/8 inches tall by 1-7/16 inches wide and are 1" thick.  They are sold in sets, enough for 1 mullion.

Von Duprin 8827 Top Latch Case for non fire rated doors. This is the part that may be causing your bottom latch to drag on the floor. The Top Latch does all the work on the Von Duprin 8827. When the Top Latch is retracted, it holds the rods in the retracted postion.

Von Duprin part # 050460
Old Part # 101750

Bobrick B-3944 recessed convertible paper towel dispenser with waste receptacle in a satin finish stainless steel. The door has a 90 degree return. dispenses 600 c-fold or 800 multifold towels. Removable leak-proof waste container has a 12 gal. capacity. Rough wall opening 16"w x 54-3/4"ht x 4" minimum depth.

The Detex ECL-230X Panic Device is a single point deadbolt device. One size fits 36 to 48 inch doors. The dead bolt has a 1 inch throw and is saw resistant. Locking and unlocking dead bolt always arms and disarms alarm.  The alarm is 100 decibels and is powered by a 9 volt battery. Email for more information.

Magnuson CLM Wall Rack

Classic wood slat design is sturdy, functional and good lookin in any setting. 5/8" diameter hanger tube accommodates theft deterrent mini-hook hangers. Available in 2, 3, or 4 foot lengths.

Available finishes are Victorian Cherry and Mahogany

Drawer Pull 3-1/2" Centers Stainless Steel, stainless steel wire pull. Measurements are 3-3/4" wide x 1-1/4" projection and the 8-32 screws are included.

Corbin Russwin ED4000/ED5000 Dogging Assembly

Used on Corbin Russian ED4000 and ED5000 Non Fire Rated Exit Devices.  The plate measures 2” x 1-7/16”, the shaft measures 1-7/16” long by 1/2” diameter.

Corbin Russwin # 650F52-8

The 780R Rubber Stair Tread is a Raised Disc.  It features an adjustable nose that drops down 1-9/16".  The nose is 1/8" thick. They are designed for interior use.

Flush Metal Toilet Partition Concealed Latch Knob And Cover

Zamac die cast construction with polished chrome plating. Outside diameter of the knob and cover are 1-5/8" with the inner ring diameter of 1-1/4". Also known as a Bathroom Stall Concealed Latch Cover and Knob Assembly. Manufacture part # 1390, 6140.

Yale 1500 Dogging Shaft

Used on the Yale 1500 Rim and Surface Vertical Rod Devices.   This is the peice that the Dogging Key goes in to actuate the Dogging Piece.   The Dogging Shaft measures 1-3/8" long and approximately 5/16" diameter.  The hex is 5/32"

Yale Part # 60-1500-1184

Ives Roller Latch RL32

The Ives Roller Latch RL32 is constructed of Brass and Plated to your desired finish.  The body measures 1-1/8" wide by 2-1/4" high and 2-1/4" deep.  The roller is constructed of Nylon, and has an adjustable projection up to 1/2".  Fits a standard heavy-duty cylindrical lock cutout.

Flush Metal Toilet Partition Bottom Hinge For 1-1/4" Square Edge Post

Chrome plated Zamac die cast construction. The hinge measures 2-1/4" high by 1-1/4" wide and the hole spacing is 1-1/2". The U channel is 2-1/4" by 1-1/4" by 1" deep. The lug projects out 1-5/8" by 1/2" thick with a 5/16" diameter bushing. Also known as a Flush Metal Bathroom Stall Pivot Hinge Bottom 1-1/4". Manufacture part # 3290

Shipped with mounting screws.

a=1-5/8"

Ives Window Bar Lift 026

Made out of Solid Brass and plated to your selected finish.  Base is 1-1/8" high by 4" wide, with a projection of 1-1/16"

Ives Part # 026B

Lyon Metal Locker Recess Handle, used Sept 2004 to current. Also known as 6748. Note the back is smooth no bolt holes for lifter. Note the previous version looks the same, but has two mounting holes on the backside- this is no longer available. 4-1/8" x 6" x 1-1/4".

Von Duprin 992/994 Lever Lift Spring 971573

The spring measures 1-5/8" long with a 7/16" diameter. We find two of these springs per 992 and 994 series lever trims. These springs help support the lever handle and return it to the proper position.

Von Duprin Part # 971573-00

892 Mop and Broom Holder - 18 gauge type 304 stainless steel channel projects 3-1/4" from the wall, fitted with spring-loaded, serrated rubber cams to hold mop and broom handles from 7/8" to 1-1/4".

5 holders

Von Duprin Exit Device 88 Wedge Ring

The Wedge Tite Screw applies pressure on the Wedge which expands the Tube Attaching Ring to grip the Cross Bar. Measures 5/8" on the flat edge.

Von Duprin Part # 090020
Old Part # 956520

FEATURES

• Please note the factory will only sell in quantities of 10.
• Supervisory key control
• Ergonomic dial with grip ring and non-slip coating
• Fully retracting automatic spring latch with standard 5/16” bolt
• Automatic locking
• 7 pre-set combinations for extended usage
• 3-digit dialing combination with 5-pin tumbler key plug
• Patent pending button guard to protect lock function from overstuffed lockers
• Nut channels for easy installation
• All Built-in Combo Locks have a 10 year warranty from time of shipment
• 72 hour shipping available

APPLICATIONS

• Model 1954 is for use with locker door hinged on right; similar in operation to Master Lock 1654
• Fits all standard single point or box lockers

1" Diameter Solid Aluminum Round

Anodized Finishes, Aluminum or Dark Brown

Cross bar has a 33-1/16" Center to Center screw spacing

Mounting Hardware Included

Toilet Partition Slide Bolt Latch Stainless Steel

Cast stainless steel construction. Latch base is 4" high with 2-3/4" hole spacing. Latch bolt is 3-3/16" long by 3/4" wide by 3/16" thick. The latch bolt clearance is 9/16" from the back of the base to the under side of the latch bolt and projects out 15/16". The latch projects out 1-9/16" from the face of the door when installed. Also known as a Bathroom Stall Surface Mounted Slide Bolt Latch and Toilet Partition Locks. Manufacture part # 5023.

Shipped with mounting screws.

also known as 9F0302SS

Detex Dogging Hex Key

The dog key has a 5/32" hex and the shaft length is 2-1/4" long.   The overall length is 3-1/8" long.

Detex part # 100450