Search results for: 'goes 8 drive bolt door hider'

Bobrick B262 surface mounted paper towel dispenser on sale today. Satin finish stainless steel. Paper dispenser holds 400 c fold or 525 multifold towels. The door has a tumbler lock with key and piano hinge for extra strength. Hemmed towel tray opening. The unit is 10-3/4" x 14"ht x 4" depth.

Cal Royal 7000 Alarmed Exit Device

Same as the Cal Royal 7700, but with these added features"

Alarm unit has internal horn. When the push rail is depressed, the horn sounds to provide an audible means of signaling that the door has been opened and violated. The unit has changeable 2 minute alarm cutoff or manual reset. Preset at factory for 2 minute alarm cut off. The key switch to turn alarm off is a standard 1 ¼” cylinder with “C” keyway. The alarm operates on one standard 9 volt transistor battery. When battery is weak the horn will emit an intermittent signal. Alarmed units are supplied with a switch that monitors push rail only. Unit includes “EMERGENCY EXIT ONLY • ALARM WILL SOUND” decal for application on door or unit.

Toilet Partition Urinal Screen Bracket Chrome Plated. This bracket is for any thickness panel. The bracket is 2 separate pieces. The base is 1-1/2" x 1-1/2". The base mounting hole is 1" from the inside face of the leg face. The bracket projects out 2-1/2", and the holes are at 2-1/8" and 1-1/8" from the mounting face. The brackets are made of a zamac die cast material and polished chrome plated. This bracket is also known as a Two Piece Bracket - Two Holes, Toilet Partition Bracket, or Bathroom Stall Bracket. The manufacturers part number is 1860 or 650-6437. The bracket is shipped as two pieces plus all of the fasteners.

Von Duprin 880TP Trim

The plate measures 3" wide by 14-3/16" long with an 1-5/8" bore hole for cylinder.

Von Duprin part # 880TP-R

The Dor-o-Matic Falcon 4758959 Soleniod is used on the EL1690, EL1790, and EL2390 Electric Latch Retraction exit devices.  The Solenoid measures 4-1/8 inches long including mouting flange, and has an 1-3/4 inch diameter.  The mounting screw spacing is 1 inch on centers. The Plunger is included and has a 7/8 inch diameter and is 2-15/16 inches long.  We find the number 971687 on the solenoid. 

7-1-2025 No longer available.  If you have the 1690 or 1790 you can update your exit to the new mortor 47867200

General Toilet Partition Bottom Hinge For 1-1/4" Sq Edge Pilaster Or Post Chrome Plated

Chrome plated Zamac die cast construction. The hinge measures 2-1/4" high by 1-1/4" wide and the hole spacing is 1-1/2". The U channel is 2-1/4" by 1-1/4" by 1" deep. The lug projects out 1-5/8" by 1/2" thick with a 5/16" diameter bushing. Also known as a General Bathroom Stall Pivot Hinge Bottom 1-1/4". Manufacture part # 3290

Shipped with mounting screws.

a=1-5/8"

Cast SS Two Ear Bracket 1" Panel 1-1/2" X 2-1/2"

Cast stainless steel construction. Base is 1-1/2" x 4" with 3" hole spacing. Bracket walls are 1/8" thick. The legs project out 2-1/2" with the thru holes at 2-1/8" from the bottom of the base. Also known as a Bathroom Stall Two Ear Wall Bracket, or Two Ear 1". Manufacture part # 1753

Shipped with mounting screws.

The Truth 11577 is used on the Encore and Maxim Awning Operators, Models Wi5100 (51.00) and Wi5110 (51.10). The operator is attached to the track by the 11647 Slide Shoe. The track measures 16 inches long by 5/8 inches wide and 5/16 inches deep.

Hardware packets are based on 4' x 8' boards.

Package includes 4 plastic anchors, 4 #3LCLIPS, 8 drill and tap screws, and 4 of the #10 phillips screws.

HD-408-BB is used for boards with item # prefixes: AA, AB, AF, AM, AN, AP, CA, CB, CT, CW, LA, PR, WB, WF, WN, WP

HD-408-WC is used for boards with item # prefixes:AW, LW, MW, WM, WS, WR

HD-408-AC is used for boards with item # prefixes: AS, MA

Roto Split Arm Operator Pin Up

The housing is 4-1/2" wide, and the linkage arm has an overall length of 4-3/8"

Left Hand shown in the picture

Von Duprin 88 Spring Tube

Spring tube measures 2-1/4" long by 3/8" diameter, steel construction.

Von Duprin Part # 050476
Old Part #951081

Friction Ring Single Wheel Caster - 2-1/2" Wheel - 7/16" Stem Diameter, 1 3/8" stem length, 2 1/2" wheel diameter. Zinc finish with black rubber wheel. Available with tread for carpet and non carpet areas. 

KK5831 hard tread for carpet

KK5832 soft tread for non carpet

ASI Locker Lock Bar 27" includes lock bar, lifter, trigger, latch clips and coiled springs. For double tier lockers, 72" overall height of locker. The lock bar is what is riding vertically to lock and unlock from the frame of the locker. When a person lifts up on the locker handle it is attached to the lock bar which releases the door from the frame of the locker.

Plastic Chair Tip Bumpers for Stacking Chair. Bumper is 1/2" Diameter, 1/4" stem diamter, 3/8" stem length, 3/16" base height and 1/2" base diameter. Available in Clear Plastic Only. 

Chrome Plated Toilet Partition Keeper Bumper Flat Stop 1-1/2" Between Screws, For Outswing

Polished chrome plated Zamac construction. The strike and keeper measure 2-1/2" high by 1-5/8" deep by 1/8" thick. The stop has a 3/4" projection and is 9/16' deep with a rubber insert. The mounting holes are 1-1/2" on center. Also known as a Bathroom Stall Strike and Keeper Outswing Flat. Manufacture part # 5260

Shipped with mounting screws.

General Partitions Bottom Hinge For 1-1/4" Round Edge

Chrome plated Zamac die cast construction. The wrap around dimension is 1-1/4" wide by 1-3/4" high and 11-16" deep. The hole spacing is 1-1/8" on center. The lug projects out 1-3/8" and is 1/2" thick with a 1/4" bushing diameter. Also known as a Bathroom Stall Pivot Hinge - Bottom 1-1/4". Manufacture part # 3420.

a=1-11/16"

Von Duprin 8827 Top Latch Case for non fire rated doors. This is the part that may be causing your bottom latch to drag on the floor. The Top Latch does all the work on the Von Duprin 8827. When the Top Latch is retracted, it holds the rods in the retracted postion.

Von Duprin part # 050460
Old Part # 101750

Bobrick B-3944 recessed convertible paper towel dispenser with waste receptacle in a satin finish stainless steel. The door has a 90 degree return. dispenses 600 c-fold or 800 multifold towels. Removable leak-proof waste container has a 12 gal. capacity. Rough wall opening 16"w x 54-3/4"ht x 4" minimum depth.

Brunswick Chair Front leg Black Rubber Feet with Metal Cap. Fits 5/8" outside diameter tubular legs.  Overall height is 1-3/4", base diameter is 1-1/4". Used on fiberglass shelled Brunswick seats.

The Republic steel #10, also known Berger #10 locker handle was made from 1960-1962. This was one of the only locker handles Republic Storage used in this time period. However, back them they were called Berger, then Republic-Berger, then Republic Steel, now they go by Republic Storage. The locker handle is 3″ overall length, 13/16″ tall, and 7/16″ wide. The lugs are 3/4″ on center and use a 8/32 x 1/2″ screw for fastening to the lock bar. The locker handle is made of a die cast material and then chrome plated. This Berger Handle is made in the USA, and is shipped with two 8/32″ x 1/2″ screws. Manufactured in the USA. Also known as 70111, 2050, 70002, rs1110, lr311.

Bobrick Toilet Partition Keeper Bumper For 1" Outswing Square Edge Post

Polished chrome plate Zamac die casting construction. Strike and Keeper measures 2-1/2" high by 1-15/16" wide. Stop is 17/32" thick and projects out 13/16". The screw holes are 1-1/2" on center. This Bathroom Toilet Door Keeper is designed for use on 1" thick square edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Outswing 1". Manufacture part # 5720.

Shipped with mounting screws.

LCN SEM7820-516 Magnet Core Assembly

Tri Voltage Magnet Core only. 35 pounds of holding force at nominal input voltage. Maximum current draw is .020 A @ 24 volt and 120 volt, and .030 A @ 12VDC.

LCN part number SEM7820-516

Horn Bleachers Vertical Push Rod, Push rod only. for right hand or left hand. 17-1/2" x 3/8". Works for right hand or left handed.

Toilet Partition Continuous 'L' Wall Bracket 2-3/4" X 57-1/2" Aluminum

Extruded aluminum construction. Base is 1-3/8" and the leg projects out 2-3/4". These are sold individually. It is also known as a Bathroom Stall Continuous L Wall Bracket. The manufacturers part # is 2684.

Shower Room Pedestal 8" x 16-1/4"ht Sold Individually. Heavy duty Bench Pedestals shall consist of steel tubing with 10 gauge steel flanges welded to each end. The overall height of pedestal shall be 16-1/4". Pedestals are to be finished to match the lockers in  Putty color.

For Hussey Bleacher 5" Wheel Axle. Overall dimensions are 3/8" axle x 2-5/16" length. 2-1/16" between grooves. This axle is also used with Folding bleacher Company. Includes clips. Also known as 1001133.

The 882 Low Profile Landing Tile is designed for use with the 820R Stair Treads.   The tiles measure 19-11/16" x 19-11/16".

Size:  19-11/16" x 19-11/16"
Overall Thickness:  1/8"

Truth 11.30 Single Pull Awning Window Operator.

11-3/8" spread when in closed position.

Includes sash hook and matching handle.

Casement Window Operator 9" Arm

Die cast housing with steel arm. The hole spacing of the window operator housing is 4-3/4" on the outside screws and 3-7/8" on the inside two screws. The arm is 9" from the roller to the center of the window operator housing. This operator uses a 5/16" spline operator, part #Ro169516.

Ro267 Right Hand
Ro268 Left Hand

Roto Casement Sash Lock

Housing measures x 4-3/4" tall by x 3/4" wide. The hole spacing is 3-15/16" center to center. The lifting finger projects out 1-1/8"" with the cut out measuring 11-16" deep by 5/16".

Threaded Stem Twin Wheel Caster -2" Wheel -1/4-20 Thread, 5/8" long stem. Chrome hood with black wheels. Available with tread for carpet and non carpet areas. 

KK8111 for hard tread for carpet

KK8112 for soft tread for non carpet surfaces

Republic Steel upper locking bar for a two person locker. 700337 spring and 700338 latch included. 7-5/8" length. Prior to current. Facing the locker the hinges will be on the Left side. Also known as 75803, 2790, 70009, rs1124, lr803.

The Truth 23.49 is a Dyad Operator is rear mounted. The linkage arm is 9-1/4 inches overall length, 8-3/4 inches hole to hole. The rear mounting holes are 5 inches on centers.

The Truth-Wright Split Arm Operator is a replacement for the older Wright Operators.  Linkage arm has an overall length of 3-5/8".

Left Hand Shown in Picture, we can only get these in white.

Republic Steel upper locking bar for a two person locker RH. 700337 spring and 700338 latch included. 7-5/8" length. Prior to current. Facing the locker the hinges will be on the Right side. Also known as 75703, 2719, 70010, rs1123, lr703.