Search results for: 'adhes base 2390 in catch base 1095 inc'

Metal Chair Swivel Glide for a chair with round tubing with measurements of 1/2" O.D. X 11/16" I.D. With Ferrule. Used on American Desk Chairs and various other manufacturers, fits 1/2" inside diameter, and 11/16" outside diameter tubing. 1 1/4" metal base. 

14 gauge (.075" thick) stamped stainless steel construction. Base is 1-1/2" x 3-15/16" with the mounting screws are 2-3/16" on center. Leg project out 2-1/2" with the thru hole at 2-1/8" from the base. Also known as a Bathroom Stall Wall Bracket and Two Wing Bracket. Manufacturer part # 1839.

Shipped with screws

Door Pull 24

This door handle features a 6" center to center screw spacing. It ships with thru bolts and finish washers. Also known as a Door Handle or Door Grip.

1" diameter material
6" centers
8" overall
3/4" base diameter
2" projection

Finishes

• Standard top pivot for heavy-duty offset
pivot sets
• Heavy-duty needle bearings are standard
• Non-ferrous base metal
• 3/4"(19mm) offset (measured from
centerline of pivot to face of door)
• Furnished with wood and machine screws

Handing diagram

The Dor-O-Matic Falcon Request to Exit Switch, SWITCH.1006 is for use on the 1690, 1790 and 2390 devices, produced after June 2002.  The Request to Exit Switch allows you to cut the current to various devices when the push bar in depressed.

Installation Instructions

Jackson Exit Device 2085 Dogging Assembly RH/LHRB

This Jackson Exit Device dogging assembly is used on the 2085 Device made after October 1, 1999. It will work on the previous version of this exit device, but you may have to use a file a remove some material from the catch.

Jackson Part # 30-2467

Partition Ada Door Handle 3-3/8" Projection X 5-1/2" Wide Cast Stainless Steel

Cast stainless steel construction. This handle a ADA compliant. The handle base is 2" diameter with 3 mounting holes on each base. The handle is made of 3/8" daimeter material. The under clearance for the handle is 3". Also known as a Bathroom Stall Door Pull. Manufacture part # 6253.

Smooth Bottom Glide Cap Protective Chair Tip

This Glide Cap has a smooth bottom to prevent your chairs from scratching your floors, while at the same time extending the life of your current glides. This cap will fit on all of our Metal and Nylon Based Swivel Glides.

This Glide Cap is designed for use with our SGR Glides, or Swivel Glides Round 1-1/4" bases.

Accurate Partitions Surface Mounted Slide Bolt Latch

Zamac die cast construction, polished chrome finish. Latch base is 4-1/2" high with 3-1/2" hole spacing. Latch bolt is 3-3/32" long by 1" wide by 3/16" thick. The latch bolt clearance is 9/16" from the back of the base to the under side of the latch bolt and projects out 15/16". The latch projects out 1-9/16" from the face of the door when installed. Also known as a Bathroom Stall Surface Mounted Slide Bolt Latch and Toilet Partition Locks. Manufacture part # 5050.

Shipped with mounting screws.

Used by accurate and global

also known as 9G0136

American Outdoor 8' X 12' Flag. Rich, lustrous appearance with superb wearing strength and breath-catching beauty. 100% nylon material, originated for flags-durable fast colors, washable, won't shrink with sewn special thread. Sheds water, flies well, even in the rain. Polyester canvas headings with spur-type brass grommets or roped headings with galvanized metal thimbles.

Lyon Metal Locker Locking Bar Spring Wire Catch, Old Style spot welded on lock bar. Used in April 1953 - February 1980.
4-3/8" overall length. Also known as 6520, 75046, ly6787, ll1743.

Door Stop / Holder Rubber Shoe

Replacement rubber shoe
1/2" insert diameter
1" base diameter
1" height

Floor Mounted Door Stop FS444

This door stop has been around a long time. We have been selling it for the past 35 years, and it is one of our best sellers year in and year out.

Features: Ideal for interior or exterior use. Cast brass construction. Accommodates door undercut up to 2-1/2". Non-marring rubber tip. Packed with expansion shield and lead shield. This Floor Mounted Door Stop is 3" high, and the base has a 2-1/2" diameter.

Toilet Partition Continuous 'L' Wall Bracket 2-3/4" X 57-1/2" Aluminum

Extruded aluminum construction. Base is 1-3/8" and the leg projects out 2-3/4". These are sold individually. It is also known as a Bathroom Stall Continuous L Wall Bracket. The manufacturers part # is 2684.

Indoor Flag Stand - 1 3/8". These cast stands are designed to compliment any flag set. Easily movable, these are the most practical stands for general use. This flag pole base is 12" diameter and 6" high. This flag stand weighs 15 pounds. 

Irwin Glide With Metal Cap

for 1/2" outside diameter tubing

product includes metal base and nickel plated tubing collar

Von Duprin 050536 HD-EL Solenoid

Electric Latch Retraction for Von Duprin Exit Devices with Hex Key Dogging.  #4 on the diagram below large picture.

Von Duprin part # 050536
Old Part # was 110740

No longer available, the only solution we have at this time is to upgrade to the HD-QEL Base Plate.

Is your Toilet Partition Bracket stamped 1310, if it is you have a one ear urinal bracket. The bracket is made from a zamac die casting that is then polished chrome plated. It sometimes goes by the name Toilet Partition One Ear Urinal Screen Bracket, Urinal Wall Bracket, 1310 Wall Bracket, 650-6410 wall bracket, or just Wall Bracket. The base is 1-1/2" wide x 2-3/4" long with a 1-1/2" on center hole spacing. The legs project out 3-1/2" with the mounting holes at 3-1/8" from the base. The holes are 1/4" diameter.

For use on 1-1/4" thick panels

Tip- Proof Flag Stand - 1 1/4". Cast stand with universal bore. Supplied with adapter sleeves to accommodate various pole diameters. Indoor Flag Stand use only. This flagstand is 10-3/4" diameter and 5-1/2" high. The flag base weighs 9 pounds. 

Door Pull 17

This door handle has an overall length of 10". The base diameters are 2" with three holes each. The handle projects out 2-1/4" and has a clearance of 1-1/2". Also known as a Door Grip or Door Handle. This handle ships with 6 wood/sheet metal screws.

Finishes

Coat Hook 3" Projection x 1-3/4" High Cast Stainless Steel

Cast stainless steel construction. The hook base measures 1-3/16" wide by 1-9/16" high. The long hook projects out 3" and the short hook projects out 1-1/2". Also known as Bathroom Stall Hook. Manufacture part # 4023.

Coat Hook 3" Projection X 1-3/4" High

Chrome plated Zamac die cast construction. The hook base measures 1-3/16" wide by 1-9/16" high. The long hook projects out 3" and the short hook projects out 1-1/2". Also known as Bathroom Stall Hook. Manufacture part # 4020.

Indoor Flag Stand - 1 1/8". These cast stands are designed to compliment any flag set. Easily movable, these are the most practical stands for general use. This flag pole base is 12" diameter, 6" high and weighs 14 pounds. Display your American Flags using this beautiful flag stand. 

Stamped SS One Ear Bracket 3/4" Panel 1-1/2" X 2-1/2"

14 gauge (.075" thick) stamped stainless steel construction. Base is 1-1/2" x 2-5/32" with the mounting screws are 1-11/32" on center. Leg project out 2-1/2" with the thru hole at 2-1/8" from the base. Also known as a Bathroom Stall Wall Bracket and One Wing Bracket. Manufacturer part # 1649.

Shipped with screws

Toilet Partition Two Ear Wall Bracket For 1 1/4" Panel Cast Stainless Steel

Cast stainless steel construction. Base is 1-1/2" x 4" with 3" hole spacing. Bracket walls are 1/8" thick. The legs project out 2-1/2" with the thru holes at 2-1/8" from the bottom of the base. Also known as a Bathroom Stall Two Ear Wall Bracket, or Two Ear 1". Manufacture part # 1833

Shipped with mounting screws.

Toilet Partition 'U' Wall Bracket For 1" Thick Panel Stamped Stainless Steel

14 gauge (.075" thick) stamped stainless steel construction. Base is 1-1/2" x 1-13/16" . Leg project out 1-1/2" with the thru hole at 1-1/8" from the base. The 4 thrue holes are 1/4" diameter, two of them are the mounting holes. Also known as a Bathroom Stall U Wall Bracket. Manufacturer part # 1919.

Shipped with screws

The offset door pull 44 is 5 inches by 12 inches.  It offers a 2 inch clearance with a 2-1/8 inch projection.  The mounting holes are 10 inches on centers.  The base block is 1 inch by 12 inches.

Hardware packets are based on 4' x 8' boards.

Package includes 4 plastic anchors, 4 of the #2LCLIPS, 4 drill and tap screws, and 4 of the #10 phillips screws.

HD-408-BB is used for boards with item # prefixes: AA, AB, AF, AM, AN, AP, CA, CB, CT, CW, LA, PR, WB, WF, WN, WP

LCN Sentronic Door Closer 4040SE-3436 On/Off Switch

The LCN 4040SE On/Off Switch measures 1" by 1/2" and the button projects up 1" from the base. This component is usually mounted by two way foam tape to isolate if for undesirable shock.

LCN Part # 4040SE-3436

Black Anodized Aluminum Kick Plate 355AN

Aluminum base material is then anodized to a Black Brushed finish
Custom sizes are available, they run about $0.25 per square inch

.040" thick
Ships with a Phillips type sheet metal screw

Please allow 7-10 days for delivery

Plunger Type Holder 582

Cast Aluminum with gray rubber shoe. 6-1/4" × 1-1/2" Base 1-5/8" Throw. Cast Aluminum finish only

Felt Pads 3/4" Diameter for a Chair Leg to prevent scratching and reduce noise.  Self adhesive so it installs in seconds. 3/16" thick. 

Ives Sweep Lock07

The Ives Sweep Lock are made of solid brass and plated to your desired finish.   The base is 15/16" x 2-9/16", and the Strike is 5/8" x 2-9/16".  The center to center distance on the screws 1-15/16".

Ives Part # 07

Toilet Partition One Ear Wall Bracket For 3/4" Panel Cast Stainless Steel

Cast stainless steel construction. Base of the bracket is 2" x 1-1/2", with 1-1/8" hole spacing. Bracket legs project out 2-1/2" with the screws at 2-1/8" on center from the base. The four holes are 1/4" diameter. Also known as a Bathroom Stall One Ear Wall Bracket or One Ear 3/4". Manufacture part # 1643.

Shipped with mounting screws.

Two Hole 1-1/2" Plastic Handle

Constructed of high density plastic with an 1-1/2" hole spacing. The lock up dimension is 3/8". The base measures 2-1/8" x 7/8". The handle measures 3-1/2" long.

The white is instock, the beige has a 1-3 week lead time.

Sanymetal Partitions Coat Hook Bumper

Chrome plated Zamac die casting construction. Coat hook bumper projects out 3" and has a rubber insert. The hook projects out 1-7/32". The coat hook bumper base is 1-7/16" wide by 2-1/4" high with a hole spacing of 7/8". Also known as a Bathroom Stall Hook. Manufacture part # 4000.