Doors

Corbin Russwin ED4000/ED5000 Blue Lever Spring

Same part as the Corbin Russwin Lever Trim Spring. Used on Yale and Corbin Russwin RHR or LH Doors. The spring has an 1-1/4" OD and 1-1/8" ID.

Yale Part # 60-7000-1224-999
Corbin Russwin # 651F62

Corbin Russwin ED4000/ED5000 Lever Spring

Same part as the Corbin Russwin Lever Trim Spring. Used on Yale and Corbin Russwin LHR or RH Doors. The spring has an 1-1/4" OD and 1-1/8" ID.

Yale Part # 60-7000-1225-999
Corbin Russwin # 651F61

Yale Trim Spring Red

Same part as the Corbin Russwin Lever Trim Spring. Used on Yale and Corbin Russwin LHR or RH Doors. The spring has an 1-1/4" diameter.

Yale Part # 60-7000-1225-999
Corbin Russwin # 651F61

Yale Trim Spring Blue

Also used on Corbin Russwin and Yale Lever trims. The Blue Spring is for RHR or LH doors. The spring has an outside diameter of 1-1/4".

Yale Part # 60-7000-1224-999
Corbin Russwin # 651F62

Von Duprin 88 Hinge Case Spring

Used on all Von Duprin 88, 8847, 8827 and 8827 Exit Devices. 4-1/2" long x 5/16" diameter.

Von Duprin Part # 090080

LCN Arm Screw

This screw goes by the number 4040-159, 4110-159, 4020-159, 1260-159, 1260-159, 4040-159 and 4040SE-159.   The screw has a 3/4" diameter head, 1/2" high with a 1/4" diameter shaft with 20 threads per inch (1/4-20 screw).

Doromatic retractor. The pinion rides inside this bracket to raise and lower the internal rods. Parts used with the retractor are the Pinion (G199005), Traveller (G199028) and the Pinion Bushing (G199046). Retractor measures 1-7/8" long by 7/8" wide by 1/4" thick.

Doromatic part # PB35 or RETRACT.101

Dor-o-Matic 1790 Slider. This is one on the components used in the NL/HB Cylinder Assy

Doromatic part # SLIDER.101 or PB344

Dor-o-Matic 1790 Repair Parts Breakdown

The Dorma 4 Loop Torsion Spring is used on the 9000 Series Exit Device Escutheon Lever Trims. Spring measures 1 inch diameter by 5/16 thick.

Dorma Part # 780367270 or 6000-717-500

• For standard weight doors
• Low frequency usage
• Packed with wood and metal screws
Not for use with a door closer.

Sold in boxes of 3
Shown in brushed brass

Ives Dome Door Stop 1-3/8" FS438

Features:

• For doors with threshold or undercut doors.
• Heavy-Duty Cast Dome Stops constructed of brass, bronze or aluminum.
• Gray, non-marring rubber bumper.

Overall hgt 1-3/8"
Base Hgt 9/16"
Base Diameter 1-3/4" x 2" Oval

Von Duprin 992/994 Lever Lift Spring 971573

The spring measures 1-5/8" long with a 7/16" diameter. We find two of these springs per 992 and 994 series lever trims. These springs help support the lever handle and return it to the proper position.

Von Duprin Part # 971573-00

Schlage Mortise Spindle and Spring

The spindle measures 2" long by 5/16".

Schlage Part # L283-060

Detex Dogging Hex Key

The dog key has a 5/32" hex and the shaft length is 2-1/4" long.   The overall length is 3-1/8" long.

Detex part # 100450

4" Kickdown Door Holder / Stop Brass Deluxe

Popular priced crafted holder for interior doors.
Has 1/2" adjustment and replaceable steel re-inforced
shoe for long life. Made of steel with brass plated finish.

Made by Grand Specialties

American Sourced and Manufactured!

Von Duprin 88 Dog Screw. Newer style, after 1975 or so. If you have an older exit device you will want to order the D100 Panic Bar Retainer.  The Old Style Dog Screw are no longer made.

Von Duprin 88 dog screw 14 threads per inch

Von Duprin Part # 090083

Detex Advantex Series End Cap 100147. Bracket measures 3-1/2 x 2-1/2 inches.

The Detex 101844-1 is the Endcap Bracket without Battery Holder. Bracket measures 3-1/2 x 2-1/4 x 5/8 inches.

Replacement Roller For Roller Bumper

Replacement wheel for the Roller Bumpers and Gravity Type Coordinators.
15/16" diameter wheel
7/16" wide wheel
3/16" diameter hub
Comes with replacement axle

3" Kickdown Door Holder / Stop Zinc Plated Mickey

Zinc plated cold rolled steel,
Made in the USA
3" Arm Length

made by Grand Specialties

American Sourced and Manufactured!

5/32" Dog Key used on old Von Durpin, and Dor-o-Matic exit devices. This key has the longer shaft to fit into the deeper Von Duprin dogging slots.

5/32" hex key

3-1/16" overall length

Von Duprin 22, 33 and 99 dogging hook, 090044

#5 on diagram

Von Duprin part # 090044
Sold individually

LCN Hold Open Arm Wrench T-1157

This wrench is used to adjust LCN Friction Hold Open Arms,
one side if for the 1-1/2" nut and the other is 1-3/16"

LCN part # T-1157

Dome Door Stop 1-5/8" Height 521

Forged brass construction with a gray rubber bumper. 1-3/4" diameter x 1-5/8" High x 1/4" Base thickness, US26D-Brushed Chrome finish only.
Supplied with wood screws and machine screws with anchors

Hager Parallel Arm Bracket

Hager Closer Std. Pa Bracket-52/53/54 Series

Hager Door Closer Standard Parallel Arm Bracket - 52/53/54 Series

Hager part # 5900

The LCN Roller Set Screw is the allen screw that holds the Roller to the Arm.  The tread is 10-32.

Corbin Russwin 20 Straight Spindle

20 TPI, 9/32" square
4" Long Straight Spindle

Sargent 20/30/60/80 Connecting Arm Spring

Push Bar Return Spring

Sargent part # 68-0236

Yale 1500 Dogging Shaft

Used on the Yale 1500 Rim and Surface Vertical Rod Devices.   This is the peice that the Dogging Key goes in to actuate the Dogging Piece.   The Dogging Shaft measures 1-3/8" long and approximately 5/16" diameter.  The hex is 5/32"

Yale Part # 60-1500-1184

Swivel spindle, 4-3/4" long,
plain centers, 20 tpi

Swivel spindle, 20 tpi,
4-3/4" long, two 3/8"
removable centers

The Norton 7700PT Arm Stud connects the arm to the slider in the track.  The Stud measures 1" overall length, including the stud head.

The Von Duprin 22, 33, 33A, 98 and 99 dogging shaft is the current dogging shaft. And has been in production since 1998.   If your device is from before 1998, then you would use the 050709.   This is the piece that the dogging key would fit into. The shaft is for a 5/32" dog key. #4 on diagram

Von Duprin Part # 090040

The Von Duprin Exit Device Dogging Adaptor Spring 090042 locks the Dogging Adaptor 090043 into the dogging mounting bracket.

Von Duprin dogging assembly part 090042
sold individually

#2 on diagram

Push Plate 50-Most Common

.050" thick 4 bevel edge

Finishes

3 x 12" GPH312
3.5 x 15" GPH315
4 x 16" GPH416
6 x 16" GPH616
4 x 20" GPH420
8 x 16" GPH816

Detex Value Series End Cap

Made of black molded plastic.  End Cap is has the numbers 101822 cast on the inside.  The hole spacing is 1-1/2" on center.

Detex part # 101822