Doors

Pull Plate 5010

The plate is .050" wought solid aluminum, stainless steel, or brass depending on the finish. The Door Pull GHE10, handles come with thru bolts. The plate has counter sunk holes and sheet metal screws in matching finish.

Finishes

3" x 12" GPL312
3.5" x 15" GPL315
4" x 16" GPL416

Pull Plate 5012

The pull plate is a .050" wought plate with Door Pull #12-6" center. The handle and plate are solid aluminum, brass or stainless steel depending on the finish ordered. Handles come with thru bolts and plate steel metal screws.

Finishes

Pull Plate 5020

The plate is constructed of .050" wrought metal, in either solid aluminum, brass or stainless steel, with Door Pull GHE20 in either 6 or 8 inch centers. Handles come with thru bolts, finish washers and the plates come with sheet metal screws that fit the countersunk holes.

Finishes

Pull Plate 5021

The plate is a .050" solid wought plate in either aluminum, brass or stainless steel depending on the finish. The Door Pull GHE21 is a half round and has 6 or 8 inch centers, handles come with thru bolts. The plates are pre drilled with counter sunk holes and come with sheet metal screws.

Finishes

Pull Plate 5025

The plate is a solid .050" wought plate of solid aluminum, brass or stainless steel depending on the finish. The Door Pull GHE25 has 6, 8 or 10 inch centers and is constructed of solid aluminum, brass or stainless steel, and is 3/4" in diameter, handles come with thru bolts. The plate come predrilled with counter sunk holes and sheet metal screws in matching finiish.

Finishes

Pull Plate 5026

The plate is a solid .050" wought plate of solid aluminum, brass or stainless steel depending on the finish. The Door Pull GHE26 has 8, 10, or 12 inch centers and is constructed of solid aluminum, brass or stainless steel, and is 1" in diameter, handles come with thru bolts. The plate come predrilled with counter sunk holes and sheet metal screws in matching finiish.

Finishes

Pull Plate 5810

7/32" thick forged plate made of solid aluminum, brass or stainless steel depending on the finish. The Door Pull GHE10, handles come with thru bolts and finish washers. The plate has counter sunk holes and sheet metal screws for mounting. 3-1/2 x 15 inch Plate only.

Finishes

Push Bar 1' Diameter 422
Bar is made of solid aluminum, Stainless Steel or Bronze. The bar comes with thru bolts for mounting

Material Size 1 " round
Base 1" Round
Clearance 1-1/8"
Projection 2-1/8"

Please allow 4 weeks on Aluminum, Polished Brass, and Oil Rubbed Bronze. Stainless Steel and Polished Stainless Steel take about 2 weeks.

One inch diameter solid push bar, 2-1/4 inch projection with 1-1/4 inch clearance and 33-1/16 inch centers.  One side is thru bolted the other is mounted on a surface mounted stud.

The 418/418S is constructed of 3/8 x 1-1/2 inch of aluminum, brass, bronze or stainless steel bar stock. It projects out 2 inches and has a clearance of 1-1/2 inches. It is available with and without a mounting pad. The mounting pad would measure 1 x 3 x 1/8 inch. The bars are shipped with mounting fasteners.

Push Bar Adjustable 450

Finishes:
US3/605 Polished brass
US4/606 Brushed brass
US10B/613 Dark bronze
US26/625 polished chrome
US26D/626 brushed chrome

Material: Brass
Material Size: 5/8" Rd Tube Adjustable up to 36"
Clearance: 1/2"
Projection: 1-1/8"
Fasteners: Surface Mount only

Push Bar Adjustable 451

Finishes:
US3/605 polished brass
US4/606 brushed brass
US10B/613 dark bronze
US26/625 polished chrome
US26D/626 brushed chrome

Material: Brass
Material Size 5/8" round tube adjustable to 36"
Base: 5/8" x 5-5/8"
Clearance: 1/2"
Projection: 1-1/8"

Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.

Push Bar Adjustable 454

Finishes:
US26/625 polished chrome
US26D/626 brushed chrome
US3/605 polished brass
US4/606 brushed brass

Material: Brass
Material Size: 1" round tube adjustable up to 36"
Base: 2" round x 2-1/2"
Clearance: 1-1/2"
Projection: 2-1/2"

Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.

1" diameter material
Establish the center to center dimension by subtracting the width of one stile from the width of the door. On solid doors, subtract 5" from the width of the door.

Please specify either wood or metal door, and its thickness; we'll supply
appropriate fasteners.

Please allow 3-4 weeks on Aluminum and Dark Bronze, and 2 weeks on the other finishes

Finishes

1" diameter materal
Offset Door Handle
Establish the center to center dimension by subtracting the width of one stile from the width of the door. On solid doors, subtract 5" from the width of the door.

Please specify either wood or metal door, and its thickness; we'll supply
appropriate fasteners.

Please allow 3-4 weeks on the Dark Bronze and Aluminum, and 2 weeks on the other finishes

Finishes

1" Diameter Solid Aluminum Round

Anodized Finishes, Aluminum or Dark Brown

Cross bar has a 33-1/16" Center to Center screw spacing

Mounting Hardware Included

1-1/4" diameter materal
Offset Door Handle
Establish the center to center dimension by subtracting the width of one stile from the width of the door. On solid doors, subtract 5" from the width of the door.

Please specify either wood or metal door, and its thickness; we'll supply
appropriate fasteners.

Please allow 3-4 weeks on the Dark Bronze and Aluminum, and 2 weeks on the other finishes

Finishes

The 422 with 49D are constructed of 1 inch solid stock, with the material determined by the finish (color). The push bar has a clearance of 1-1/8 and the handle has a clearance of 1-1/2 inches. The projection is 2-1/8 on the push bar and 2-1/2 inches on the handle. The pull handle is 12 inches on center, with a 7 inch offset. The set comes with two 5/16-18 thru bolts and one 5/16 back to back conehead.

The M422 with M49D are constructed of 1-1/4 inch solid stock, with the material determined by the finish (color). The push bar has a clearance of 1-1/2 and the handle has a clearance of 1-1/2 inches. The projection is 2-3/4 on the push bar and 2-3/4 inches on the handle. The pull handle is 12 inches on center, with a 7 inch offset. The set comes with two 5/16-18 thru bolts and one 5/16 back to back conehead.

Push Bar with Posts has a 1 inch diameter push bar and the mounting posts are 7/8 inch round. The bar has a clearance of 1-1/2 inches and a projection of 2-1/2 inches. Base material is either aluminum, brass, bronze or stainless steel depending on the finish. To order specify the Color (finish), Mounting Center to Centers, Bar overall length, and Door Thickness.

Push Bar with Posts has a 1-1/4 inches diameter push bar and the mounting posts are 1 inch round. The bar has a clearance of 1-1/2 inches and a projection of 2-3/4 inches. Base material is either aluminum, brass, bronze or stainless steel depending on the finish. To order specify the Color (finish), Mounting Center to Centers, Bar overall length, and Door Thickness.

Push Plate 50-Most Common

.050" thick 4 bevel edge

Finishes

3 x 12" GPH312
3.5 x 15" GPH315
4 x 16" GPH416
6 x 16" GPH616
4 x 20" GPH420
8 x 16" GPH816

Push Plate 58

3-1/2" x 15" x 7/32"

Finishes

Push Plate 59

The push plate measures 7-1/2" wide x 15" tall x .050" thick. This plate is shipped with the mounting screws.

Finishes

Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.

Push Plate 60

8" x 16" x .050

Finishes

Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.

Push Plate 61

7-1/2" x 15" x .050
Handed
LH Shown

Finishes

Push Plate 62

7-1/2" x 15" x .050
Handed
LH shown

Finishes

Push Plate 65

3" x 15" x .050

Finishes

Push Plate 70

.125" thick with 4 beveled edges. Base material is either aluminum, brass, bronze or stainless steel depending on the finish. This would be considered a premium push plate.

Finishes

The 80 Series Push Plate is similar to the 70 series, but has a round bevel on the top and bottom of the plate. There is no bevel on the sides. These plates are  an 1/8 inch thick and are available many different finishes and size.  Custom sizes are available, and they ship with the matching finish mounting screws.

Push Plate 89

.125" thickness
3-1/2" x 15-3/4" Forged

Finishes

Push Plate Plastic 90

1/8" thickness plastic

The Burns Manufacturing 455 Adjustable Push/Push units consists of 2 454 push bars and and 1 453 pull bar. They are adustable up to 36". The tubes are 1 inch round and the bases are 2 inch diameter by 2-1/2 inch projection. The base metal is brass.

Reinforcing Pivot Hinge 4" - for use with a 4" wide butt hinge

1/2" to center line of 4" hinge.
Used to strengthen and reduce vibration
to your current full mortise butt hinges.
Made of Zinc Plated Steel

These hinges are not longer handed. Please select hand when checking out, until our system is updated.