Doors

Von Duprin 22, 33 and 99 dogging hook, 090044

#5 on diagram

Von Duprin part # 090044
Sold individually

LCN Hold Open Arm Wrench T-1157

This wrench is used to adjust LCN Friction Hold Open Arms,
one side if for the 1-1/2" nut and the other is 1-3/16"

LCN part # T-1157

Dome Door Stop 1-5/8" Height 521

Forged brass construction with a gray rubber bumper. 1-3/4" diameter x 1-5/8" High x 1/4" Base thickness, US26D-Brushed Chrome finish only.
Supplied with wood screws and machine screws with anchors

Detex Value Series End Cap

Made of black molded plastic.  End Cap is has the numbers 101822 cast on the inside.  The hole spacing is 1-1/2" on center.

Detex part # 101822

Hager Parallel Arm Bracket

Hager Closer Std. Pa Bracket-52/53/54 Series

Hager Door Closer Standard Parallel Arm Bracket - 52/53/54 Series

Hager part # 5900

Corbin Russwin 20 Straight Spindle

20 TPI, 9/32" square
4" Long Straight Spindle

Sargent 20/30/60/80 Connecting Arm Spring

Push Bar Return Spring

Sargent part # 68-0236

Yale 1500 Dogging Shaft

Used on the Yale 1500 Rim and Surface Vertical Rod Devices.   This is the peice that the Dogging Key goes in to actuate the Dogging Piece.   The Dogging Shaft measures 1-3/8" long and approximately 5/16" diameter.  The hex is 5/32"

Yale Part # 60-1500-1184

Swivel spindle, 20 tpi,
4-3/4" long, two 3/8"
removable centers

Swivel spindle, 4-3/4" long,
plain centers, 20 tpi

The Norton 7700PT Arm Stud connects the arm to the slider in the track.  The Stud measures 1" overall length, including the stud head.

The Von Duprin 22, 33, 33A, 98 and 99 dogging shaft is the current dogging shaft. And has been in production since 1998.   If your device is from before 1998, then you would use the 050709.   This is the piece that the dogging key would fit into. The shaft is for a 5/32" dog key. #4 on diagram

Von Duprin Part # 090040

The Von Duprin Exit Device Dogging Adaptor Spring 090042 locks the Dogging Adaptor 090043 into the dogging mounting bracket.

Von Duprin dogging assembly part 090042
sold individually

#2 on diagram

Push Plate 50-Most Common

.050" thick 4 bevel edge

Finishes

3 x 12" GPH312
3.5 x 15" GPH315
4 x 16" GPH416
6 x 16" GPH616
4 x 20" GPH420
8 x 16" GPH816

Von Duprin Exit Device 88 Tube Attaching Ring

Von Duprin 55 and 88 Tube Attaching Ring.

Used as a sleeve the wedge tite screw and wedge use to apply pressure to the crossbar. Measures 15/16" long by 13/16" diameter.

Von Duprin Part #090021
Old Part # 965676

Schlage Mortise Spring Cage

Spring cage measures 1-1/2" x 1-1/2" x 1/4" thick. Screw spacing is 1-1/16" on center.

Schlage Part # L283-040

Monarch Trim Spring 4841

2-1/2" long x 3/16" diameter

Monarch part # 4841

International Door Closer 520 Main Arm

International Door Closer part # 520

International 521 Forearm

Arm measures 9-1/2" loop to loop in the shortest position, and 14" when it is the fully extended . The loop on the left side is 3/8" diameter. The hole spacing on the right hand side of the picture shoe is 1-3/4".

International part # 521

4" Kickdown Door Holder / Stop FS455

Features:

• Units provide simple hold and release, activated with a touch of the foot.
• Cast brass or aluminum construction.
• Non-marring rubber shoes have corrugated bottoms to provide secure grip and a shank which forms its own thread when screwed into threaded cavity of holder.
• When worn, shoes are easily replaced.
• Door-to-floor clearances of 2" or less.

Made by H.B. Ives

Von Duprin 55 Dog Screw-090053

3/8" diameter x 1/2" long
new style 14 threads per inch

Von Duprin part # 090053

Von Duprin 55 Hinge Case Spring

Von Duprin 55 hinge case spring, spring lifts arm.

1-5/8" long x 5/8" diameter

Von Duprin part # 090052

4" Kickdown Door Holder / Stop FS544

This is one of our most popular Kickdown Door Holder/Stop for the past 35 years.

Features:

• Units provide an economical method to hold open doors.
• Cast of durable iron.
• Non-marring rubber shoes have corrugated bottoms to provide secure grip. Rubber shoe is securely fastened with screw. When worn, shoes are easily replaced.
• FS544 for door-to-floor clearances of 2" or less.

The Monarch / Dor-O-Matic / Falcon 600339 NL Spring Package converts the 179L , 712L, 712K, 912l and 911K to an NL function.   The NL function is  one were the Lever Handle can not be unlocked and left in the unlocked position when the key is removed.   Spring has a 5/8" diameter.  See attached instructions.

Doromatic Exit Device 1690/1790 Pushbar Anchor Bracket

Doromatic Part # PB321 or BRKT.128

The Monarch 4326 Spring Clip is used with the 4841 Spring in the older Monarch Lever Trims

The Yale 7000 Cylinder Dogging Sub Assembly is used on non Fire Rated Yale and Corbin Russwin panic devices.   Like the Hex Key Sub Assembly, this one is for use with a Key Cylinder.

Yale Part # 60-7000-0407-999
Corbin Russwin Part # 650F968

Dor-o-Matic 1690 Pinion Support Bracket. Bracket holds pinion tip so that it will not slip

Doromatic part # BRKT.478, BRKT.133 or PB312

Dor-o-Matic 1690 Repair Parts Breakdown

4" Kickdown Door Holder / Stop Grand Standard

No roll pin at pivot point
Mallable with a pair of pliers
Rubber shoe held on by a screw
American Made

Made by Grand Specialties

Zinc plated steel or Brass plated

Another feature is their well constructed shoe can be adjusted down as the rubber wears making the holder last way longer than their competitors. Another use for them is as a door floor lock if mounted on the other side of the door. Once kicked down there's no entry possible unless you slide a flat item under the door to lift the door holder leg out of the way and push the door open. It can be opened from the inside as normal with your foot or hand. A very inexpensive security lock.

Doromatic 1690/1790/2390 replacement dogging hex shaft. Replaces the allen wrench fitting for the Doromatic exit devices

A tough mineral-coated waterproof non-slip surfacing with a pressure sensitive adhesive back. Helps grip foot traffic, preventing slipping, easy to apply; use inside or outside. Rectangular sizes with rounded corners or in rolls cut to any length. We suggest priming surfaces with Musson Grit Strip Adhesive before applying. Ideal for entranceways, ramps and walkways, stairways, heavy traffic areas, work areas, loading docks, recreational vehicles, boats & docks, cafeterias, kitchens, coolers, around drinking fountains and ice machines.

Black Rolls only on this page, see Grit Strip Colored Rolls or Grit Strip Precut

Dor-o-Matic 1490/1590 Dogging Compression Spring

Doromatic part # 4299101020 or PB224

Falcon Monarch Bottom Bolt Guide Assembly

The Falcon Monarch Bottom Bolt Guide Assembly 650387 is used the 19-V, 24-V, 25-V and the XX-V Bottom Rod.  The Guide Assembly measures 1-7/8" tall by 1" wide and projects 1-9/16" at the widest projection.   The Bottom Bolt Guide is made of zinc plated steel.

Falcon Monarch Part # 650387

The Von Duprin Dogging Adaptor is the female part that holds the dogging shaft in place.

Von Duprin dogging assebly part

#1 on diagram

Von Duprin part # 090043

Sold individually

The Adams Rite 31-0964 is used on the 3500, 8600, 8675 and 4781 Devices. The assembly comes with the nylon bushing.