Doors
-
Jackson 1085 Lever Arms
Jackson 1085 Lever Arms
Replacement Lever Arm for the Jackson 1085 Housings, both sides. And the Jackson 1095 Inactive (hinge side) Housings. Handing is determined by standing inside and looking out, if the arm in on the right hand side of the door, it is a right hand lever that you would order.
Jackson Part # RH 30-1242/LH 30-1243
G10852x -
Jackson 1095 Lever Arms
Jackson 1085 Lever Arms
Replacement Lever Arm for the Jackson 1095 Active Housings. This arm will only work on the 1095 Active Case! Handing is determined by standing inside and looking out, if the arm in on the right hand side of the door, it is a right hand lever that you would order.
Jackson Part # RH 30-1247/LH 30-1248
G10955X -
Yale 1500 Dogging Shaft
Yale 1500 Dogging Shaft
Used on the Yale 1500 Rim and Surface Vertical Rod Devices. This is the peice that the Dogging Key goes in to actuate the Dogging Piece. The Dogging Shaft measures 1-3/8" long and approximately 5/16" diameter. The hex is 5/32"
Yale Part # 60-1500-1184
G6015001184 -
Ives Roller Latch RL30
Ives Roller Latch RL30
The Ives Roller Latch RL30 is constructed of Forged Brass and Plated to your finish. Furnished with a Nylon Roller. Body measures 1" wide by 3-3/8" high by 1-11/16" deep. The roller has a maximum projection of 3/8" and is easily adjustable.
RL30- -
Ives Roller Latch RL32
Ives Roller Latch RL32
The Ives Roller Latch RL32 is constructed of Brass and Plated to your desired finish. The body measures 1-1/8" wide by 2-1/4" high and 2-1/4" deep. The roller is constructed of Nylon, and has an adjustable projection up to 1/2". Fits a standard heavy-duty cylindrical lock cutout.
RL32- -
Sargent 2828 / 2838 Center Case Cam
Sargent 2828 / 2838 Center Case Cam
The Sargent 2828 / 2838 Center Case Cam is the Cam that the key cylinder actuates to open the door. The Cam is located in the middle of the Center Case. We can no longer get the retaining ring to hold it in place.
Sargent Part # 28-0109
G280109 -
International Door Closer 300 Series Adjustable Power
International Door Closer 300 Series Adjustable Power
UL Listed, Barrier Free Operation to Comply with Federal Accessibility Standards (ADA) ANSI A117.1. Spring Power adjustable for a range of sizes from 8-1/2 lbs t Medium Spring Tension, fully adjustable after installation.
Hydraulic Cylinder only
3000-B-310 105 with Hold Open
3000-B-311 105 with No Hold Open
3000-B-312 90 with Hold Open
3000-B-313 90 with No Hold Open3000-B -
Von Duprin 9975 Exit Only
Von Duprin 9875/9975 mortise lock device for all types of single or double doors, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1. Fits stock hollow metal doors with 86 cutout and door stiles as narrow as 4-3/4" (121mm). The Von Duprin 9875 device has a smooth mechanism case and the Von Duprin 9975 device has a grooved case. The mortise lock device is non-handed
9975EO -
Von Duprin 99 Exit Device Only
The Von Duprin 99 rim exit devices for all types of single and double doors with mullion, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1. The Von Duprin 98 device has a smooth mechanism case and the Von Duprin 99 device has a grooved case. The rim device is non-handed.
Ships with all the mounting screws and the 299 Strike.
99EO -
Von Duprin 88 Active Case
Replacement Von Duprin 88 Rim Device Center Case
Includes all of the internal parts and hardware. This case works with all Exit Only, Dummy and Night Latch Trims. Call or email us if you have a Lever, Knob or Thumb Piece Trim.
Von Duprin Part # 050409
Old Part # 10166288R10 -
Von Duprin Exit Device Keyed Mullion Retrofit Kit
Von Duprin Exit Device Keyed Mullion Retrofit Kit
Keyed Removable Steel Mullions makes removal faster and easier by a single operation of the mortise cylinder. Once mullion is removed, large equipment or furniture can freely pass through the opening. The unit will self lock when re-installed, without use of the cylinder key. Uses a 1-1/4´´mortise cylinder with a
straight cam (Schlage cam reference B502-191). Cylinders are sold separately. Prefix mullion model with “KR”.Von Duprin Part # 050168
KR54 -
Von Duprin 2670 Guard-X Exit Device
Heavy Duty Design
The new Series 2670 Exit Alarm Lock provides secure protection through a large stainless steel deadbolt, which is 2" x 1/2" (51mm x 13mm) and has over a 3/4" (19mm) throw. The engagement area into the strike is over 1 1/4" (32mm) square inches. The cast aluminum latch case protects the internal mechanism and resists tampering or vandalism from inside the door. This unit has been tested to withstand up to 1600 pounds of static load force against the door.Fits 36" to 48" doors.
Uses 9 volt battery
Ships with all mounting hardware and strike.2670EO- -
Von Duprin Exit Device 99 Lever Trim
The Von Duprin 996L Lever Trim replaces the 992L, and 994L and is the latest generation of the 99 Lever Trim.
The escutcheon plate measures 2-3/4" wide by 10-3/4" high and projects out 27/32". The handle projection is 2-7/8". This lever handle is handed, but is field reversible. Key lock and unlocks lever.
ver.99L -
Von Duprin Exit Device 990TP Trim
The Von Duprin 990TP Trim is the standard Thumb Piece Trim for the 99 and 98 Series devices. The plate is constructed of Bronze or Stainless Steel and then plated to the desired finish. The plate measures 3" wide by 14-3/16" tall, and includes the mounting screws. The stanchions coming off the back of the plate line up with the center case mounting screws. The key cylinder locks and unlocks the thumb piece. The Rim Cylinder shown in the picture is not included.
Von Duprin Part # 990TP-R&V
Cylinder not included.
99TP -
Von Duprin 99 Push Bar Retrofit Kit-Pbkit
Von Duprin 99 Push Bar Retrofit Kit-Pbkit
Von Duprin's 98/99 Push Bar Retrofit Kit updates your current version touch pad, to the newest version. Used on all the Von Durpin 33A, 35A, 99 and 98's.
Von Duprin part # PBKIT
For doors 30" to 36" order the 36" size. If your door is 36" to 48" order the 48" size
G99R35 -
Von Duprin Exit Device 990NL Trim
The Von Duprin 990NL Trim is the standard NIght Latch Trim for the 99 and 98 Series devices. The plate is constructed of Bronze or Stainless Steel and then plated to the desired finish. The plate measures 3" wide by 14-3/16" tall, and includes the mounting screws. The stanchions coming off the back of the plate line up with the center case mounting screws. The Rim Cylinder shown in the picture is not included.
Von Duprin Part # 990NL-R&V
99NL