Manufacturers
-
-
Cal Royal 2000 Alarmed Exit Device
Cal Royal 2000 Alarmed Exit Device
Alarm units has an internal horn. When the push rail is depressed, the horn sounds to provide an audible means of signaling that the door has been opened and violated. The unit has changeable 2 minute alarm cutoff or manual reset. Preset at factory for 2 minute alarm cut off. Jumper cable is provided to swich to continuous alarm. The key switch to turn the alarm off is a standard 1” cylinder with “C” keyway. The alarm operates on one standard 9 volt transistor battery. When battery is weak the horn will emit an intermittent signal. Alarmed units are supplied with two switches. One switch monitors the push rail and the other switch monitors the latch bolt for full proof security.
Unit includes “EMERGENCY EXIT ONLY. ALARM WILL SOUND” decal for application on door or unit.ALM2000 -
Sargent Exit Device Lever Return Spring
Sargent Exit Device Lever Return Spring
This spring is used on Sargent Lever Trims for there Exit Devices.
2-1/8" LONG
Sargent part # 97-0425
G970425 -
Sargent 20/30/60/80 Dogging Assembly
Sargent 20/30/60/80 Dogging Assembly
We only sell the dogging assembly parts as a complete set. This Dogging Assembly Kit is used on the Sargent 20, Sargent 30, Sargent 60, and Sargent 80 Series Exit Devices. This dogging assembly kit has been around since the 1980's.
Sargent part # 68-2596
G80200 -
Doromatic Exit Device 1990 Repair Kit PBX-2
Dor-o-Matic 1990 repair kit. The kit includes the following:
4 Mounting Studs
1 Hex Key 7/32"
1 Allen Key 1/8"
1 Pinion
1 Cylinder Bushing
2 Rod Bushings
1 Retractor
1 Traveller AssyDoromatic part # 4270902091 or PBX-2
GPBX2 -
Doromatic Exit Device 1690/1790/2390 Dogging Assembly Kit.1197
Doromatic 1690 1790 replacement dogging assy. The dogging assembly is used to dog the door in the open position, so people can enter the building without having to unlatch the door. The kit ships with form threading screws for installation.
Doromatic part # KIT.1197
Dor-o-Matic 1690 Repair Parts Breakdown
Dor-o-Matic 1790 Repair Parts Breakdown
Falcon / Dor-o-Matic 2390 Parts Break Down<GPBX16 -
Monarch 19-V Exit Device
Monarch 19-V Exit Device
Hand: Field reversible.
Functions: All functions built into “EO” device.
Finishes: Powder-coated aluminum–SP28; powder-coated duranodic–SP313;
Latchbolt: Top stainless steel 3⁄4" throw. Bottom square bolt 1⁄2" throw.
Deadlocking Latchbolt: Standard.
Dogging Feature: 1⁄2 turn hex dogging standard. No threaded parts to wear out.
Stock Sizes: 3'0" and 4'0"
Doors: 13⁄4" thick, wood or metal.
Narrow Stile Doors: To 1-3⁄4" N.S. aluminum. With control trim–2-1⁄4" min. stile.
Projection: 2-1⁄2" max., 1-7⁄8" dogged.G19VEO- -
Dor-O-Matic 2390 231CA Cylinder Kit
The Dor-O-Matic 2390 231CA Cylinder Kit converts your 2390 exit only to a Night Latch or Hold Back function key lock. All the hardware is included in the package to convert your device, except for the Mortise Cylinder. Housing measures 4-1/2" tall by 1-11/16" wide with a 1-1/8" projection. We send the 231CA which includes the Schlage B502-191 Cam. The 239CA is the same kit, but without the Schlage Cam.
231CA- -
Von Duprin Exit Device 990TP Trim
The Von Duprin 990TP Trim is the standard Thumb Piece Trim for the 99 and 98 Series devices. The plate is constructed of Bronze or Stainless Steel and then plated to the desired finish. The plate measures 3" wide by 14-3/16" tall, and includes the mounting screws. The stanchions coming off the back of the plate line up with the center case mounting screws. The key cylinder locks and unlocks the thumb piece. The Rim Cylinder shown in the picture is not included.
Von Duprin Part # 990TP-R&V
Cylinder not included.
99TP -
Von Duprin Exit Device 990NL Trim
The Von Duprin 990NL Trim is the standard NIght Latch Trim for the 99 and 98 Series devices. The plate is constructed of Bronze or Stainless Steel and then plated to the desired finish. The plate measures 3" wide by 14-3/16" tall, and includes the mounting screws. The stanchions coming off the back of the plate line up with the center case mounting screws. The Rim Cylinder shown in the picture is not included.
Von Duprin Part # 990NL-R&V
99NL -
Von Duprin Exit Device 99 Lever Trim
The Von Duprin 996L Lever Trim replaces the 992L, and 994L and is the latest generation of the 99 Lever Trim.
The escutcheon plate measures 2-3/4" wide by 10-3/4" high and projects out 27/32". The handle projection is 2-7/8". This lever handle is handed, but is field reversible. Key lock and unlocks lever.
ver.99L -
Von Duprin 990DT Trim
The Von Duprin 990DT Trim is the standard Dummy Trim for the 99 and 98 Series devices. The plate is constructed of Bronze or Stainless Steel and then plated to the desired finish. The plate measures 3" wide by 14-3/16" tall, and includes the mounting screws. The stanchions coming off the back of the plate line up with the center case mounting screws.
Von Duprin Part # 990DT-R&V
99DT- -
-
-
Adams Rite EX88 Rim Exit Device
The Adams Rite EX88 Interlocking Rim Exit Device is designed for heavy duty use on narrow stile aluminium door applications. The EX88 has a unique latch bolt design that interlocks with the frame of the door. This device is non handed, requires a minimum stile width of 2" and will work on aluminum, hollow metal or wood doors.The device is constructed of extruded aluminum with matching metal angled end caps. To order specify your door width, and the color.
EX88- -