Search results for: '3 8 x 1 2 hiny brook'

GSA11 ALUMINUM STAIR TREADS

Diamond hard aluminum oxide abrasives combined with "space-age" polymeric binders are bonded to a heat treated high strength aluminum square nose stair tread. Treads are available GSA75-7-1/2", GSA9-9" or GSA11-11" deep; in one or two contrasting colors per tread. Flat pieces, GSA35-3-1/2" or GSA55 5-1/2" deep, can be used for ramps and other non-step applications or as a filler behind the 7-1/2" treads. Select one color for front insert and the same or a different color for back insert from seven standard abrasive colors of black, brown, blue, gray, green, red or yellow. Maximum lenght is 10 foot. Nose drops 1-1/16".

Install outdoors or indoors on concrete, wood, treated lumber, slate or marble steps. Use for motels, schools, hotels, apartments, condos, hospitals, churches, cruise ships, amusement parks, etc. Offers anti-slip safety surface - protects new steps - renovate slippery, worn steps.

Purchase the 11" model here.

The 1010R Rubber Stair Tread features a Rib Design, with grooves all along the fall line.   The sqaure nose is not tapered or adjustable.  The nose is 1/8" thick and tapers to 3/32" at the very back. They are designed for interior use.

The 780R Rubber Stair Tread is a Raised Disc.  It features an adjustable nose that drops down 1-9/16".  The nose is 1/8" thick. They are designed for interior use.

775 EPOXY FLOORING ADHESIVE

The only recommended adhesive for use with Disc-O-Tile. May be used with other rubber stair treads, tile and flooring. Because of flame spread properties, other adhesives will not bond Disc-O-Tile to the floor. A two-part solvent-free adhesive; contains 1 can Part A 1 can Part B, and a stirring paddle. Covers approximately 150 square feet per unit. Enviromental Friendly!

Adhesive information

The 520S Rubber Stair Tread has a 1/4" nose thickness which tapers down to 1/8" at the back.  The nose drops down 1-9/16", and the nose is not adjustable and is not tapered. They are designed for interior use.

Standard narrow corrugated surface is completely tested through- out. Conforms to ANSI/ASTM D178 J6.7 Type II Class 2. Stays in place, is slip resistant. With care, lightweight carts can be used over this runner.

Meets Dielectric Test Volt, RMS AC 30,000; Proof Test Volt, RMS AC 20,000. Recommended maximum use Volt, RMS AC 17,000.

Fully meets ASTM specifications branded on back. Black color only. Available in standard rolls or cut to exact length desired.

Sold by the foot

The 782 Raised Disc Landing Tile is designed for use with the 780R Stair Treads.   The tiles measure 19-11/16" x 19-11/16".

Size:  19-11/16" x 19-11/16"
Overall Thickness:  5/32"

Adhesive specifically designed for the TT-12 Fluff Cord Tile.

1 gallon covers approximately 100 square feet

Adhesive information

Use adhesive where Grit Strip is applied to porous surfaces such as wood or concrete. Grit Strip adhesive is recommended as a sealer; will give a better, longer lasting bond. Recommended application temperature is 60 degrees and above. One quart covers approximately 50 square feet (single coat) of Grit Strip; available in quart and pint units.

Adhesive information

The 7520R is a smooth surface rubber stair tread.   These treads come in Square and Round Nose, this page is for the Round Nose, for Square Nose search 7520R. The treads are 1/8" thick along the entire depth of the treads, and have a nose that drops down 1-9/16".  The 7520R Round Nose is not available with the Grit Stripping. They are designed for interior use.

320 CARPET TILE ADHESVIE

A special latex emulsion pressure sensitive adhesive formulated for installation of modular carpet tiles or carpet matting. Adhesive is non-flammable, water resistant and has excellent resistance to vinyl plasticizer migration. Adhesive remains tacky for an extended period - allows tile to be picked up and replaced without affecting adhesive. Remove tiles from floor more easily than with conventional adhesives, simplifying reinstallation of tile sections or a complete area.

Covers 200 to 300 square feet per gallon
Sold in 1 or 4 Gallon Pails

For installing Rubber Floor Tiles or Rolls over suitable on-grade dry concrete floors, suspended concrete floors, or suspended wood floors. May also be used with sanded back molded rubber stair treads. Not recommended where excessive moisture exists; Non-Carcinogenic; Non-Toxic; safe for the environment and freeze thaw stable. See label for complete instructions. Ready to trowel in 1 gallon or 4 gallon cans. Covers 150 square feet per gallon.

Adhesive information

The 620D Rubber Stair Tread comes in two versions, Square Nose and Round Nose.  This page is for the Square Nose, Search 620DRN for the Round Nose Version.   This tread offers an 1/8" nose thickness, has an adjustable and tapered nose. They are designed for interior use.

The 630D Rubber Outdoor Tread is the only tread we recommend for exterior applications. The tread is only available in black and is ideal for ice rinks, sports arena and high traffic areas.  The tread is 12-1/16" deep with the last 3 inches being smooth for trimming in the field. 

405CR Vinyl Stair Tread Risers

Plain color cove risers match Koroseal vinyl stair treads; or use a contrasting riser with vinyl or rubber treads; easily trimmed in height and length; savings in installation are substantial; cove risers are same sizes as stair treads.

SPECIFICATIONS:

Furnish and install No 405CR Koroseal vinyl coved stair riser; 1/8” thick, 7” high with 5/8” toe; ribbed back. Select standard length of 18”, 24”, 30”, 36”, 42”, 48”, 54”, 60”, 72”, 84” or 96”. Select standard solid color of Brown, Sand, Gray or Black.

The 7020 is a smooth surface rubber stair tread.   These treads come in Square and Round Nose, this page is for the Square Nose, for Round Nose search 7020RD. The treads are 1/4" thick at the nose and taper to 3/16" at the rear.  For the Grit Stripped version you would order the 2020. They are designed for interior use.

KT18 Vinyl Landing Tiles

Landing tiles are .120" thick by 18" x 18" and designed to go with all the vinyl stair treads.  Available colors are Shale and Amber.  Shale is for use with the Black and Gray treads, and the Amber is for use with the Brown or Sand color treads.

The 7020 is a smooth surface rubber stair tread.   These treads come in Square and Round Nose, this page is for the Round Nose, for Square Nose search 7020. The treads are 1/4" thick at the nose and taper to 3/16" at the rear. For the Grit Stripped version is not available for the round nose treads. They are designed for interior use.

FLUFF-CORD STRIP TILE

A close-nap carpet-like surface of specially processed rubber-fabric strips made from recycled heavy-duty truck and bus tires; Natural Earthtone Gray Color. Strips are heat bonded to a woven flexible backing. This creates a "dry-back" adhesive back that reacts with our non-flammable adhesive to form a stronger bond to the floor. Install this permanent entry floor mat inside or outside; cord strips act as a wiper where dirt or moisture is a problem; are non-skid, non-absorbing, resist shrinkage, deaden sound. Ideal for heavy wear areas in shopping centers, lobbies, entryways, ramps, airports, etc. Produced in standard 12" x 12" tile size.

Tile must be installed using manufacturer's specific installation instructions and Musson No. TT-390 Non-Flammable Environmentally Safe Adhesive.

Order Fluff-Cord Strip Tiles here

Designed for use in apartments, urban renewal housing, housing for the elderly and housing projects. Lower initial cost, ease of installation and cleaning, and long service appeals to owner and builder. Extra thick at front; Meets Fed. Specs. RR-T-650E Type B. They are designed for interior use.

Features:

• Extra thick at front
• Easy installation
• Easy clean
• Meets Fed. Specs. RR-T-650E Type B
• Contains no asbestos fiber
• Made of first quality homogeneous vinyl
• Color throughout thickness
• Free from imperfections which might lessen serviceability

Specifications:

• 375 Koroseal vinyl rib design stair treads by R.C. Musson
• Thickness: 3/16"
• Depth: 12"
• Nose: 1-1/4" square or curved
• Sizes available: 18", 24", 30", 36", 42", 48", 54", 60", 72", 84", 96"
• Colors available: Brown, Sand, Gray, Black

FLUFF-CORD STRIP TILE-CONTINUOUS STRIP

A close-nap carpet-like surface of specially processed rubber-fabric strips made from recycled heavy-duty truck and bus tires; Natural Earthtone Gray Color. Strips are heat bonded to a woven flexible backing. This creates a "dry-back" adhesive back that reacts with our non-flammable adhesive to form a stronger bond to the floor. Install this permanent entry floor mat inside or outside; cord strips act as a wiper where dirt or moisture is a problem; are non-skid, non-absorbing, resist shrinkage, deaden sound. Ideal for heavy wear areas in shopping centers, lobbies, entryways, ramps, airports, etc. Produced in longitudinal rolls 12" wide x 25' long.

Tile must be installed using manufacturer's specific installation instructions and Musson No. TT-390 Non-Flammable Environmentally Safe Adhesive.

Order Fluff-Cord Strip Rolls here

The 605CR Rubber Coved Riser goes in the back of the step and acts as a kick plate in the matching color of your stair treads.  The Riser is 7" tall and features a 5/8" cove to aid in cleaning of the back of the step.

Vinyl Stair Treads GS365 with Grit Strip

This is one our highest volume vinyl stair treads. Heavy duty to stand up to most applications with the safety of inlaid grit strips. Made in the USA

SPECIFICATIONS:

Furnish and install No. GS365 Koroseal Vinyl Stair Treads
Grit-Strip rib design stair treads; 7/32" thick, 12" deep; 1-1/4" square nose; two black* 1" wide abrasive Grit-Strips inlaid in tread, 1" from front edge, spaced 1-1/4" apart; contains no asbestos fiber; made of first quality homogenous vinyl, color throughout thickness; free from imperfections which might lessen serviceability. Meets Federal Specs. RR-T-650E Type B. Select standard length of 36", 42", 48", 54", 60", 72", 84" or 96". Select standard solid color of Brown or Gray.

The 920R One-Piece Rubber Stair Tread has a 3/16" thick nose and tapers to 5-16" at the back.  The nose is adjustable and tapered for a perfect fit.  The benefit of a one piece tread is the ease of cleanng, there is not a groove at the back of the step to collect debris. They are designed for interior use.

A non-solvent based alternative to install rubber and vinyl stair treads and cove risers to concrete, wood, terrazzo, metal or marble. One gallon covers 75 lineal feet of stair treads (brush on back of tread and step). Ready to use in 1 quart, 1 gallon and 4 gallon containers.

Adhesive information

400 Vinyl Stair Treads

Heavy gauge sharp-rib design Koroseal vinyl treads for heaviest traffic; 1/4" thick at wear area, easily trimmed to cover and fit any stair step. Install over concrete, metal, wood, terrazzo. Extra heavy thickness at the front "wear area". Meets Fed. Specs. RR-T-650E Type B. They are designed for interior use.

SPECIFICATIONS:

No. 400 Koroseal vinyl rib design stair treads 1/4" thick 12" deep; 1-1/4" square nose; contains no asbestos fiber; made of first quality homogeneous vinyl, color throughout thickness; free from imperfections which might lesson serviceability. Select standard length of 24", 30", 36", 42", 48", 54", 60", 72", 84" or 96". Select standard solid colors of Brown, Sand, Gray or Black.

For bonding to all Disc-O-Treds, Rubber Stair Treads or Koroseal Vinyl Stair Treads to concrete, pan filled, wood, metal, marble and terrazzo steps. A rapid drying, long range contact cement; specially formulated for Musson stair coverings. Brush on application; use on back of treads and back of nosing. Contains solvents, extremely flammable. 1 gallon covers 75 lineal feet of stair treads (brush on back of tread and step). Ready to use in 1 quart, 1 gallon and 5 gallon containers.

If ordering the gallon or 4 gallon pail, it will ship via freight truck. If you would prefer something that ships Fed Ex Ground, please order the 300 Stair Tread Adhesive.

Adhesive information