Search results for: 'case extens mountjackson exit device model 1095 top caps'

Von Duprin 8827 replacement latch covers

Latch covers come with matching screws

Von Duprin Part # 050464
Old Part # 960548

Von Duprin 050536 HD-EL Solenoid

Electric Latch Retraction for Von Duprin Exit Devices with Hex Key Dogging.  #4 on the diagram below large picture.

Von Duprin part # 050536
Old Part # was 110740

No longer available, the only solution we have at this time is to upgrade to the HD-QEL Base Plate.

Von Duprin 33/3547 99/9947 Ratchet Lever Spring (2)

One of two springs located in the 33/3547 and 98/9947 Top Latch 050492.  Sold in packages of 2.

Von Duprin Part # 090069

Von Duprin 9927 Latch Covers.

This cover is used on the 2227, 3327A, 3427A, 9827 and 9927 Exit Devices. Replace old bent and worn covers with brand new ones.

Includes mounting screws

Von Duprin Part # 050566

Other finishes are available

Von Duprin 9927 Bottom latch

Replaces and updates all 9827 and 9927 bottom latches to the new style, if your device was installed before October 1998. If your device is newer then October 1998, then use the G050401. Mounting screws are included.

Includes screws and bracket

Von Duprin Part # 050090

Von Duprin 8827-F Bottom Latch Kit 050463

This is the Bottom Latch Kit for the Von Duprin 8827-F. The 8827-F is the Fire Rated Surface Vertical Rod device usually used on interior doors to contain a fire. The Fire Rated version would not have dog screws to lock the device in the retracted postion.

Von Durpin Part # 050463
Old Part # 102681

Von Duprin 1606 Rim Device Strike for Panic Devices only.  Strike measure 1-3/8 x 2-7/8 with a 3/8 inch projection. The hole spacing is 2-1/8 inches.

Von Duprin 8827 Chassis Tie Rod Pkg 050328

The 8827 Chassis Tie Rod Package is the rod that goes through the top and bottom latches. The Tie Rod is held in place by the Special Chassis Nut. The Tie Rod measures 1-3/8" long by 3/16" diameter.

Von Duprin Part # 050328
Old Von Duprin Part # 967616

Von Duprin 55 Rim Latch Bolt Spring

Von Duprin 55 Rim Device Latch Bolt Spring

1-1/2" long x 3/8" diameter

Von Duprin part # 967502

Von Duprin 88 Latch Tail Springs

This is the spring that pushes the latch bolt out. Used on all Von Duprin 88 Rim Devices. The spring measures 2-5/8" long by 3/16" diameter.

Sold in packages of 2.

Von Duprin Part #050393

The Von Duprin 900581 Cylinder Cup and Tail Piece Assembly is used on just about everyone of their devices outside tirm.

Von Duprin Strike 499F

The Von Duprin 499F is used on the 22, 98 and 99 Series Fire Rated Rim Devices when used with the 9954 Mullion.

The Von Duprin 338 Strike measures 1-5/8" by 1-7/8" with a 5/8" projection.   The screw mounting is 1-7/8".   This strike is used as a bottom strike on the Von Duprin surface and concealed vertical rod devices.

The Von Duprin Old Style Dogging Shaft was used on devices manufactured before July 1997.  The Shaft measures roughly 1-1/2" long with a 1/2" diameter.  The hex is 5/32".

Von Duprin Part # 968112

Von Duprin Strike 1409

This Von Duprin Strike is used for the bottom latch of the 22, 33, 33A, 55, 88 and 99 Rim Devices.  Also known as a Blade Stop.

The Von Duprin 090039 is used in the push bar assembly to return the latch. It is known as the Base Plate Latch Return Spring or Latch Return Spring. It is used on the 22, 33A, 35A, 98 and 99 Devices. The spring is 2-1/4 inch long with a 3/8 inch diameter.

The Von Duprin 33/99 Cylinder Dogging Conversion Kit 050155

Converts the Hex Key Dogging 33A and 99 Devices to Cylinder Dogging.  The kit does not include the key cylinder, which is a Mortise Cylinder.

Von Duprin Part # 050155

Von Duprin Strike 299F

The Von Duprin 299F Strike is used on the 22, 88, 98, and 99 Fire Rated Rim Devices (no hex or cylinder dogging). The 299F strike measures 1-1/4" wide by 2-7/8" high with a slotted hole spacing of 2-1/8". The roller projects out 13/16". The non fire rated version would be the Von Duprin Strike 299.

Ships with shim and mounting screws

Von Duprin Strike 1609

This strike is used when we have a double door application without a center post. By using this strike we can have one door with a surface vertical rod and one door a rim device, which will save money because vertical rods are usually expensive. This strike can be used with the Von Duprin 22/2227, 88/8827, 98/9827 and 99/9927 combinations, but not with the Fire Rated Versions. The strike base measures 1-1/16" wide by 3-1/4" high, the lip projects out 7/8". The three slots are 1-1/4" on center. This strike ships with the mounting screws.

US19-Black finish

Von Duprin Strike 248L-4

The Von Duprin 248L-4 Strike is used as a Bottom Strike on the 2227, 8827, 9927, and 9827 Surface Vertical Rod Panic Devices. The 248L-4 strike measures 9/16" wide by 2-1/2" high with a hole spacing of 1-7/8. The strike projects out 3/8".

Ships with shim and mounting screws

Von Duprin Strike 248L-4

Burnished steel construction

Von Duprin Electric Strike 6112 24VDC

Von Duprin 6100 Series electric strikes are designed for use with Rim devices.  The 6112 has a 3/4” latch bolt throw, 9” face plate length, 1-5/8” width, and an 1-3/4” backbone depth.  The lock retrofits the Folger Adams FA 310-4.  Other voltages and replacement parts are available. 

FSE - Fail-secure.  Requires power to be applied to unlock the strike lip.  On loss of power, the strike lip is locked-Fire Rated

FS - Fail-safe.  Requires power to be applied to lock the strike lip.  On loss of power, the strike lip is unlocked.  Non Fire-Rated.

Von Duprin Electric Strike 6113 24VDC

Von Duprin 6100 Series electric strikes are designed for use with Rim devices.  The 6113 has a 3/4” latch bolt throw, 6” face plate length, 1-5/8” width, and an 1-15/16” backbone depth.  The lock retrofits the VD 3011 and VD 3021.  Other voltages and replacement parts are available. 

FSE - Fail-secure.  Requires power to be applied to unlock the strike lip.  On loss of power, the strike lip is locked-Fire Rated

FS - Fail-safe.  Requires power to be applied to lock the strike lip.  On loss of power, the strike lip is unlocked.  Non Fire-Rated.

Von Duprin 5547 Bottom Rod Kit

Von Duprin 050036 5547 Bottom Rod Kit

Von Duprin Part #050036
Old Von Duprin Part #102551

Von Duprin Electric Strike 6114 24VDC

Von Duprin 6100 Series electric strikes are designed for use with Rim devices.  The 6114 has a 3/4” latch bolt throw, 7” face plate length, 1-7/8” width, and projects1-9/16”.  The lock retrofits the Folger Adams FD 310-5.  Other voltages and replacement parts are available. 

FSE - Fail-secure.  Requires power to be applied to unlock the strike lip.  On loss of power, the strike lip is locked-Fire Rated

FS - Fail-safe.  Requires power to be applied to lock the strike lip.  On loss of power, the strike lip is unlocked.  Non Fire-Rated.

Von Duprin 9927 Latch Cover Screws 

Von Duprin 050538 EL Dogging Rod Retainer

This fitting threads into the 050536 HD Solenoid and connects to the Dogging Rod

#5 On Diagram

Von Duprin 55 Dog Screw-090053

3/8" diameter x 1/2" long
new style 14 threads per inch

Von Duprin part # 090053

Von Duprin 88 NL Cylinder Cam

Von Duprin part # 951970 and 050502

Von Duprin Aluminum Mullion 5654 7'2"

The Von Duprin Aluminum Mullion 5654 comes prepped for two of the 299 Strikes.  Everything is included, except the the 299 strikes.

Von Duprin 230L Tailpiece Auxiliary Kit

The Von Duprin 230L Tailpiece Auxiliary Kit includes the Tailpiece, Tailpiece Guide, and the Pine Tree Clip.

Von Duprin Part # 900894

The Von Duprin Latch Mounting Bracket 050546 is used on the 2227, 3327 and 9927.   It is for use with the 050400, 050401, 050091 and 050090 Surface Vertical Latches.

Von Duprin Part # 050546
Old Von Duprin Part # 971567

Von Duprin 88 Latch Tail, Spring and Rivet Kit

The Von Duprin Part # 050500 includes the 1 Latch Tail, 2 Latch Tail Rivets, and 2 Latch Tail Springs.

Von Duprin 55 Arm Brushing

Von Duprin 55 Arm Bushing fits in the 55 housing

13/16" outside diameter x 5/16" high

Von Duprin Part #  050333
Old Von Duprin Part # 959986 

Von Duprin 1654/4754/4854/4954 Bottom Fitting

This is the Bottom Fitting for the 1654, 4754, 4854, and 4954 Von Duprin Mullions. Mounting Screws included.

Von Duprin Part # 050390

Von Duprin 98/9947 Adjustable Bottom Rod

This rod is used on the 9847, 9847-F, 9947 and 9947-F

Von Dupin Part # 050575
Old Part #112342