Search results for: 'adhes base 2390 in catch base 1095 inc'

Chrome Plated Two Ear Urinal Bracket For 1-1/4" X 1-1/2" X 3-1/2

This bracket is constructed of zamac die cast material that is then polished chrome plated. The base is 1-1/2" wide x 4" long, with two screws 3" on center. The legs project out 3-1/2" with the thru screws at 3-1/8" and 2-1/8" from the base. The 6 holes are 1/4" diameter. This bracket is also known as a Toilet Partiton Bracket, Bathroom Stall Bracket, Two Ear Extra Long Bracket, Two Wing Bracket, Urinal Screen Bracket X-Long. The manufacturers part # are 1330, and 650-6449. The bracket includes all the fasteners.

This bracket is for a 1-1/4" thick panel

Chrome Plated Heavy Duty Partition Ada Throw Latch And Keeper

Polished chrome plated brass construction. Latch base is 2" x 2" and is 3/16" thick. The throw latch is 5-7/16" long by 1-1/4" by 7/32" thick. The keeper is 2" by 2" by 21-32" high. Meets ADA codes in most States. Also known as a Bathroom Stall Heavy Duty ADA Throw Latch and Keeper and Toilet Partition Locks. Manufacture part # 5701.

Shipped with mounting screws.

Partition Door Stop 2" High Cast Stainless Steel

Cast stainless steel construction. The door stop base is 2-1/8" diameter with a 1-19/32" hole spacing. The stop projects out 2" with a rubber insert on the end of the stop. Also known as Bathroom Stall Door Stop. Manufacture part # 4123.

Partition Door Stop 2" Projection

Chrome plated Zamac die cast construction. The door stop base is 2-1/8" diameter with a 1-19/32" hole spacing. The stop projects out 2" with a rubber insert on the end of the stop. Also known as Bathroom Stall Door Stop. Manufacture part # 4120.

Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.

The C Shaped Offset Pull has 12 inch centers and has a 13 inches overall lenght. The clearance is 1-1/2 inches with a 2-1/2 inch projections. The handle is constructed on 1 inch diameter stock, the offset is 7 inches. The base is 7/8 inch round stock. The handle is furnished with thru bolts and finish washers.

Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.

Chrome Plated Slide Bolt Latch 9/16" Bar To Door Clearance

Zamac die cast construction with polished chrome plating. Base is 3-3/8" high with 2-5/8" hole spacing. Latch bolt is 3-1/8" long by 7/8" wide by 3/16" thick with a 9/16" dimension from the door to the under side of the latch bolt. The latch projects out 1-1/2" when installed on the door. Also known as a Bathroom Toilet Stall Door Slide Latch and Toilet Partition Locks. Manufacture part # 6540.

Shipped with mounting screws.

Toilet Partition Urinal Screen Bracket Chrome Plated

Constructed of polished chrome plated zamac die cast. The wall mounted base is 7" across with 6" center to center screw holes. The bracket projects out 12" and the two thru holes are 7" on center. The bracket is designed for use on 1" thick panels or urinal screens. The 6 holes are 1/4" diameter. This bracket is sometimes called the 2700 Wing Bracket, 650-6440 Wing Bracket, Urinal Screen Bracket, Urinal Screen Wing Bracket, Bathroom Stall Wing Bracket, or Toilet Partitoin Screen Bracket

Von Duprin 360L Lever Trim

The Von Durpin 360L Lever Trim has a base measurement of 7-1/2" high by 1-11/16" wide and 7/8" thick. The lever is 4-1/2" and projects out 3". This lever Trim uses a 1-1/4" Mortise Straight Cam Cylinder.

Von Duprin Part # 360L

Chrome plated Zamac die casting construction. Coat hook bumper projects out 3" and has a rubber insert. The hook projects out 1-7/32". The coat hook bumper base is 1-7/16" wide by 2-1/4" high with a hole spacing of 7/8". Also known as a Bathroom Stall Hook. Manufacture part # 4000.

Push Bar Adjustable 451

Finishes:
US3/605 polished brass
US4/606 brushed brass
US10B/613 dark bronze
US26/625 polished chrome
US26D/626 brushed chrome

Material: Brass
Material Size 5/8" round tube adjustable to 36"
Base: 5/8" x 5-5/8"
Clearance: 1/2"
Projection: 1-1/8"

The Burns 617 Non-Locking Pocket Door Pull Set is 2-3/4 inches tall by 2-1/2 inches deep. The mortise dimensions are 2-5/16 inches tall by 1-7/8 inch deep. Base metal is Brass or Aluminum depending on the finish.

Anodized Duranodic Aluminum Kick Plate 313AN
Aluminum base material is then anodized to a dark brown duranodic finish
Custom sizes are available, they run about $0.25 per square inch

.040" thick
Ships with matching phillips head sheet metal screws.

Please allow 7-10 days for delivery

Felt Pads 1" Diameter, self adhesive for easy installation in seconds. Prevents scratching on floors and reduces noise made by chairs. 3/16" thick, NO LONGER AVAILABLE IN GRAY, THEY ARE NOW A TAN COLOR. 

Aluminum Diamond Plate Kick Plate

Aluminum base material that has a polished chrome look with the diamond plate pattern. Diamonds are 1-1/8" long.
Custom sizes are available, they run about $0.39 per square inch

.125" thick

Please allow 7-10 days for delivery

Fiat Partitions Coat Hook Bumper

Chrome plated Zamac die casting construction. Coat hook bumper projects out 3" and has a rubber insert. The hook projects out 1-7/32". The coat hook bumper base is 1-7/16" wide by 2-1/4" high with a hole spacing of 7/8". Also known as a Bathroom Stall Hook. Manufacture part # 4000.

Floor Mounted Door Stop Heavy Duty 540

This Floor Mounted Door Stop is a personal favorite. It is extremely heavy duty, and is ideal for areas of high vandalism. Includes the 4-1/2" lag bolt & lag shield. The rubber base is 3" in diameter and is 2-5/8" high.  Uses a 3/4" diameter hole for the lag sheild.

Handicap Door Pull 19

With this handle you are able to get a closed fist behind the pull, which makes it a great ADA Door Pull. Shipped with screws. Also known as a Handicap Grip, ADA Door Pull or Handle.

Finishes

A tough mineral-coated waterproof non-slip surfacing with a pressure sensitive adhesive back. Helps grip foot traffic, preventing slipping, easy to apply; use inside or outside. Rectangular sizes with rounded corners or in rolls cut to any length. We suggest priming surfaces with Musson Grit Strip Adhesive before applying. Ideal for entranceways, ramps and walkways, stairways, heavy traffic areas, work areas, loading docks, recreational vehicles, boats & docks, cafeterias, kitchens, coolers, around drinking fountains and ice machines.

Black Rolls only on this page, see Grit Strip Colored Rolls or Grit Strip Precut

Doromatic Surface Strike STK45

This strike is used when we have a double door application without a center post. By using this strike we can have one door with a surface vertical rod and one door a rim device, which will save money because vertical rods are usually expensive. This strike can be used with the 1590, 1790 and 2090 Rim Devices. The strike base measures 1-5/16" wide by 3-1/4" high, and 1/4" thick. The three slots are 1-1/4" on center. This strike ships with the mounting screws.

US19-Black finish

Sanymetal Partition Keeper 2" Between Screws Inswing Flat

Polished chrome plated Zamac construction. Keeper base is 3" high by 1-1/16" wide with a 2" hole spacing. Strike is 3" tall by 7/8" deep. The material 1/8" thick. The slot is 1-1/8" high by 1/4". Also known as a Bathroom Stall Keeper Inswing Flat. Manufacture part # 5130.

Shipped with mounting screws.

This Glass Patch is sold in rolls of 18 inches by 120 inches.  It is a polyester film with an adhesive back with "Warning" on it to prevent accidental injury. This is a temporary transparent patch until the Glass can be replaced.

Republic Steel Locker Handle #11 Assembly Right Hand. Comes with lift,case and screws.Our replacement Republic Storage Handles are based on the version they produced in the 1970″s, which means more material on the legs (lugs). The extra material makes them much more heavy duty then the ones they are producing today. We sell the Republic Storage #11 Locker Handle three ways, just the lift, just the case or the complete assembly. The case and the assembly come with the mounting screws. The Republic Storage #11 handle, also goes by Republic Steel #11 handle, and Berger #11 handle. The #11 handle has been produced since the 1962-1965. Also known as 70107, 2040, 70035, rs1107, lr306.

For bonding to all Disc-O-Treds, Rubber Stair Treads or Koroseal Vinyl Stair Treads to concrete, pan filled, wood, metal, marble and terrazzo steps. A rapid drying, long range contact cement; specially formulated for Musson stair coverings. Brush on application; use on back of treads and back of nosing. Contains solvents, extremely flammable. 1 gallon covers 75 lineal feet of stair treads (brush on back of tread and step). Ready to use in 1 quart, 1 gallon and 5 gallon containers.

If ordering the gallon or 4 gallon pail, it will ship via freight truck. If you would prefer something that ships Fed Ex Ground, please order the 300 Stair Tread Adhesive.

Adhesive information

Toilet Partition Angle Bracket Chrome Plated 1 3/4" X 1 3/4"

Constructed of stainless polished finish with chrome plated zamac die casting. Base is 1-3/4" x 1-3/8", projects out 1-3/4". Two screw holes are 1/4" diameter, and are located 1-1/4" from opposing face. Sometimes called Bathroom Stall Angle Bracket. Sold individually, and shipped with required screws. Manufacturer part number 2015.

Coat Hook & Bumper 3-1/2" Projection x 2-3/4" High Chrome Plated

Chrome plated Zamac construction. Coat hook base is 1-1/2" wide by 2-3/4" high, with screw spacing of 7/8" at the top. Hook projects out 1". Bumper projects out 3-1/2" with a rubber insert. Also known as a Bathroom Stall Coat Hook and Bumper. Manufacture part # 4260.

Same as 9OT285, 9HA426

Republic Steel Locker Handle #11 Assembly Left Hand. Comes with lift,case and screws.Our replacement Republic Storage Handles are based on the version they produced in the 1970″s, which means more material on the legs (lugs). The extra material makes them much more heavy duty then the ones they are producing today. We sell the Republic Storage #11 Locker Handle three ways, just the lift, just the case or the complete assembly. The case and the assembly come with the mounting screws. The Republic Storage #11 handle, also goes by Republic Steel #11 handle, and Berger #11 handle. The #11 handle has been produced since the 1962-1965. Also known as 70108, 2045, 70036, rs11108, lr307.

Occupancy Indicator Handle Set, European Design, Stainless Steel Construction. This product offers the European style with a sleek and modern feel. Features the capability of being installed on partitions with thickness of either 3/4" or 1", Built-In Handle, and Emergency unlatching access on front face of indicator, make this an extremely versatile option for restroom partitions. Traditionally these are designed for partitions that have routed edges to create a no-sightline system but can be used with non-routed edge partitions with addition hardware under related products.

Republic Steel Locker Handle Lift #11 Right Hand (Lift Only). Our replacement Republic Storage Handles are based on the version they produced in the 1970″s, which means more material on the legs (lugs). And our handles are made in the U.S.A. in Wisconsin. The extra material makes them much more heavy duty then the ones they are producing today. We sell the Republic Storage #11 Locker Handle three ways, just the lift, just the case or the complete assembly. The case and the assembly come with the mounting screws. The Republic Storage #11 handle, also goes by Republic Steel #11 handle, and Berger #11 handle. The #11 handle has been produced since the 1962-1965.

The 1 inch diameter Decorative Cap comes in two different tread sizes 1/4-20 and 5/16-18.  The Cap measures 1 inch diameter by 3/8 inch thick. Stainless Steel base material.

Anodized Gold Aluminum Kick Plate
Aluminum base material is then anodized to a polished brass finish. These plates are a great alternative to the Solid Polished Brass and Lifetime Brass kick plates. Custom sizes are available, they run about $0.24 per square inch or less.

.040" thick
Ships with matching Phillips type sheet metal screws

Please allow 7-10 days for delivery

Cast Stainless Steel Partition Keeper 1-1/2" Between Screws

Cast stainless steel construction. Keeper base is 2-1/2" high by 1-3/16" wide with a 1-1/2" hole spacing. Strike is 2-1/2" tall by 7/8" deep. The material 1/8" thick. The slot is 13/16" high by 1/4". Also known as a Bathroom Stall Keeper Inswing Flat. Manufacture part # 5183.

Shipped with mounting screws.

Door Stop, Pilaster Mounted, 2-1/2" X 4-1/4", Stainless Steel.

Cast Stainless Steel construction. The door stop base is 3" wide by 1-1/4" high with a 2-5/16" hole spacing. The stop projects out 2-1/2" and has a rubber insert in it. This door stop is usually mounted on the pilaster or post. Also known as a Bathroom Stall Door Stop. Manufacture part # 4153.

The reinforcing pivot hinge is a good way to solve door sag issues. And also be a preventative solutions for future isses with extra heavy or wide doors. The hinges comes in two sizes 4 or 4.5 inches, and two finishes, prime coat and satin chrome. The hinge uses a heavy duty ball-bearing to add extra life.  The base metal is steel.

Our replacement Republic Storage Handles are based on the version they produced in the 1970′s, which means more material on the legs (lugs) and housings. The extra material makes them much more heavy duty then the ones they are producing today. We used to sell the Republic Storage #12 Locker Handle three ways, just the lift, just the case or the complete assembly, however we are no longer able to procure the components individually. The case and the assembly come with the mounting screws. The Republic Storage #12 handle, also goes by Republic Steel #12 handle, and Berger #12 handle. The #12 handle has been produced since the 1965 and is still produced today. Also known as 70102, 2030, 70001, rs1106, lr302.