Plastic Chair Tips for Square Tubing chair legs with a 7/8" Outside Diameter X 3/4" Inside Diameter Legs. This tip is a rocker type tip for slanted square legs and available in black. 

Used on chairs and table, so you can use an adjustable height gilde. Used with the LA10625 or SLA12525. 1/4-20 Thread, 1-1/4" outside diameter and 1-1/8" inside diameter. 

The 7020 is a smooth surface rubber stair tread.   These treads come in Square and Round Nose, this page is for the Round Nose, for Square Nose search 7020. The treads are 1/4" thick at the nose and taper to 3/16" at the rear. For the Grit Stripped version is not available for the round nose treads. They are designed for interior use.

The Aluminum Vinyl Door Shoe constructed of extruded aluminum and black vinyl.  This shoe is sold in 36 and 48 inch lengths and comes with #6 x 3/4 inch stainless steel sheet metal screws.

DORMA 9300 Series Exit Devices minimize forced entry while offering a low-cost solution to life safety requirements. Certified/listed to ANSI/BHMA 156.3 Grade 1 for exit devices. Package includes all the mounting screws and brackets, and the surface strike.  5 year limited warranty.

Swivel Glide Square tubing Leg with a  13/16" O.D. X 11/16" I.D. The base on this chair glide is 15/16" in diameter. This swivel based chair glide features a ferrule. 

Used on chairs and table, so you can use an adjustable height gilde. Used with the LA10625 or SLA12525. 1/4-20 Thread, 1-1/8" outside diameter and 1" inside diameter.

Metal Swivel Based Chair Glide with a round tubing leg measurements of  3/4" O.D. X 5/8" I.D. This chair glide does NOT feature a Ferrule, This glide has a clip that holds the glide on by going inside the chair leg. The Chair Glides Base diameter is 1 1/4". 

The same as the Falcon / Dor-o-Matic 1690 with Mechanical Electric Latch Retraction. Some of the features are listed below. A power supply is required.

Hand: Field reversible, non-handed.
Centercase and end cap are powder-coated black only.
Strikes: PB48 top.
Latches: Hex bottom latch (standard), RL - rod bottom latch, PL - Pullman bottom latch
Cylinder: Rim, key entry (NL) or hold back (HB) feature available.
Field selectable.
Sizes: 30", 36", 42", and 48".
Doors: 1-3/4" thick metal doors, specify if other.
Projections: 3-3/8" in neutral position, 23/8" in dogged position.
Pushbar height is 2-1/2.
Stile: 1-3/4" minimum.

Replacement parts are also available

Shipped with all screws and strikes.

The 7520R is a smooth surface rubber stair tread.   These treads come in Square and Round Nose, this page is for the Square Nose, for Round Nose search 7520RRD. The treads are 1/8" thick along the entire depth of the treads, and have a nose that drops down 1-9/16".  For the Grit Stripped version you would order the 220 or the 2520.  The 220 comes with two 3/4" grit strips, the 2520 would be the visually impaired version with one 2" wide strip. They are designed for interior use.

Door Pull Offset 1" Diameter PH-4000

1" Diameter Solid Aluminum Round 3-1/4" Offset Door Pull, usually used on aluminum frame glass doors. This handle offers three different mounting options, one is surface mounted, where the handle is mounted over a mounting stud and then you tighten the set screw to hold the handle in place. The second method is thru bolted, the bolt goes all the way thru the door. And the third is back to were you have two handles mounted back to back.

Projection 3 -1/4"
Door Clearance 2 -1/4"
Center To Center 9". 10' and 12"
Anodized Finishes Aluminum or Dark Brown
Mounting Hardware Included

Square Leg Metal Swivel Glide with a 1-1/16" base diameter. This Chair Glide does not have ferrule. This swivel glide is for a square tubing chair leg with a 7/8" outer diameter and a 3/4" innner diameter. 

Black Round Plastic Chair Tips for Round Tubing Chair Legs with a 1-1/2" Outside Diameter X 1-3/8" Inside Diameter. 

Rubber Chair Tips For Legs With An Outside Diameter Of 1". Chair tip is for Hampden, Krueger and Samsonite Chairs. Available in Black or Gray.

Plastic Chair Tips Square Tubing for 7/8" Outside Diameter X 3/4" Inside Diameter Leg. Fits square tubing legs with an outside diameter of 7/8" and an inside diameter of 3/4". Available in Black only. 

Metal Swivel Chair Glide with a 11/16" O.D. X 9/16" I.D. W/O Ferrule. Measurement is the chair leg diameters.  Used as a replacement for the American Seating glide, used on the Alert Line chairs. This chair glide has a 1 1/4"  metal base diameter. The clip at the top holds the glide on by going inside the leg.  

Sargent 3828 Series Exit Device

The 3828 is a rugged exit device in a rim design. The 3828 Non Configured Rim Exit Device has 7 functions, 4 available trims and is easy to mix and match the device and trim. Aluminum finish only.

Square Plastic Chair Tips for Square Tubing chair leg with a 3/4" Outside Diameter X 5/8" Inside Diameter Legs. Square tips for a slanted leg chair. Available in Black. 

Retractable Wood Grain Phenolic Seat lh,This L-shaped reversible shower seat is ADA compliant and comes with a one-piece, one-half inch thick wood-grain phenolic top.  The reversible L-shaped component allows the handing of the seat to be determined in the field.  The seat is 32 inches by 23 inches and includes a self-locking mechanism to secure the seat in the upright position when it is not in use.  The tubular components are fabricated from stainless steel.

Plastic Chair Tips for Square Tubing Chair Legs with a 1-1/2" Outside Diameter X 1-3/8" Inside Diameter Legs. Available in Black only. 

1" Diameter Solid Aluminum Round

Anodized Finishes, Aluminum or Dark Brown

Cross bar has a 33-1/16" Center to Center screw spacing

Mounting Hardware Included

This is the same trusted Von Duprin 99 with Electric Latch Retraction, also known as EL.

The EL feature allows for the remote unlatching of exit devices. A control station operator can flip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. A powerful, continuous duty solenoid retracts the latch bolt, either for momentary unlatching, or for extended periods of time. The EL feature is an alternative to manual dogging.

The rim device is non-handed.
A power supply is required for operation, see related products.
Ships with all the mounting screws and the 299 Strike.

This L-shaped reversible shower seat is ADA compliant and comes with a one-piece, one-half inch thick ivory phenolic top.  The reversible L-shaped component allows the handing of the seat to be determined in the field.  The seat is 32 inches by 23 inches and includes a self-locking mechanism to secure the seat in the upright position when it is not in use.  The tubular components are fabricated from stainless steel.

Saddle Threshold 426 - 6" Wide By 1/2" High

Extruded aluminum construction. The thresholds are shipped with mounting screws (#10 x 1-1/2" FH zinc plated wood screws), Milled aluminum finish. This is considered a Handicap Saddle Threshold.

Other sizes and finishes are available, call for more information.

Air shipment is not available on this product. Please allow 7-10 days for delivery.

Square Plastic Chair Tips for Square Tubing chair legs with a 1" Outside Diameter X 15/16" Inside Diameter chair Leg. This tip is a rocker style tip for use with slanted square chair legs and comes in black only. 

Toilet partition round edge pilaster shoe, stamped stainless steel construction. Pilaster Shoe measures 2" to 24" wide by -1-1/4" thick by 3" high. This size pilaster post shoes are split on one end for easy installation. Also known as a Bathroom Stall Pilaster Post Shoe Round Edge. Used for the base of the support system with pilaster mounting.

Swivel Based Chair Glide for round tubing with measurements of 7/8" O.D. X 3/4" I.D. This chair glide does NOT feature a Ferrule, This glide has a clip that holds the glide on by going inside the chair leg. The Chair Glides Base diameter is 1 1/4". 

Bobrick stainless steel straight grab bars for 1-1/2" diameter with a snap on flange to conceal the screws. Type 304 stainless steel tubing. Maximum weight capacity is 250lbs Known as B-6806x18, B-6806x36 and B-6806x42.

Aluminum Store Front Door Flush Bolt FB-1202

15/16" x 4-1/4" radius face, 5-7/32" hole spacing, 1/8" offset, 5/8" throw, 12" rod length, with a square nylon tip with beveled corners fits in a 1/2" square hole.

Non swivel glides for round tubing

1" outside diameter
7/8" inside diameter
1-1/16" base diameter
Nickel plated metal base

Chair Glide for a square leg chair with tubing outer diameter 3/4" and inner diameter of 5/8". 1 1/16" Base diameter. This glide does not have a ferrule.  

Rubber Crutch Chair Tips for 5/8" Round Chair Legs. 5/8" is the outisde diameter of your chair leg. Rubber Crutch tips help protect your floors from expensive damage. A variety of sizes available in both tan and black color. 

CRT62B BLACK

CRT62 TAN

Cal Royal A2200V Surface Vertical Rod

Grade 1
Non handed-field reversible
Heavy gauge steel, painted
4-1/2" minimum stile width

24" wide x 84" high, and 32" wide and 84" high also available in aluminum only.

International 7100 Concealed Vertical Rod Device

Modern flat touch bar Concealed Vertical Rod Device Panic exit device. This series offers durability, safety and meets the security demand and access control needs of today. Series 7300 Rim Panic exit devices are used with Narrow, Medium and Wide aluminum door and Hollow Metal and Wood Door applications. Series 7300 is non-handed, Field Reversible for LHRB or RHRB doors. Outside Unlatching and Dogging by Cylinder Key or Dogging by Hex Key in Touch Bar. Standard Units for 36” and 48” in widths (cut bar to fit). Can be used on 30” wide doors.

Black Round Plastic Chair Tips for Round Tubing chair legs with a 3/4" Oustside Diameter X 5/8" Inside Diameter. Available in black only. 

ADA Sliding and Barn Door Push/Pull Set. Pull handle is 3/4" round stock with 6" center to centers and 2-1/2 inch clearance.  The flush pull is 4" x 7" x 1-1/8 inch ADA.