Door Pull Offset 1" Diameter PH-4000

1" Diameter Solid Aluminum Round 3-1/4" Offset Door Pull, usually used on aluminum frame glass doors. This handle offers three different mounting options, one is surface mounted, where the handle is mounted over a mounting stud and then you tighten the set screw to hold the handle in place. The second method is thru bolted, the bolt goes all the way thru the door. And the third is back to were you have two handles mounted back to back.

Projection 3 -1/4"
Door Clearance 2 -1/4"
Center To Center 9". 10' and 12"
Anodized Finishes Aluminum or Dark Brown
Mounting Hardware Included

Krueger Swivel Glide for 5/8" Inside Diameter and 3/4" Outside Diameter Tubing

Plastic swivel glide for use on Krueger Chairs and Desks.

International Door Closer 200 Series Overhead Door Closer

UL Listed
Built in positive back stop and hold open positions.
Two speed control valves: Closing and latching speeds controlled by separate regulating valves, fully adjustable after installation.
Positive centering for alignment and to hold door closed against any normal wind or draft.
Stable hydraulic door check fluid for any climatic operation and constant lubrication.

Hydraulic Cylinder only

2000-B-230 105 with Hold Open
2000-B-231 105 with No Hold Open
2000-B-232 90 with Hold Open
2000-B-233 90 with No Hold Open

Doromatic 1590 Latch Bolt Assembly

Replacement Latch Bolt Assembly for the Falcon Doromatic 1590.   In the old days you could just replace the PB355 (SPRING.127) spring, but as of November 2015 you have to replace the complete latch head assembly.

Doromatic Part # 4270107603

Non-Swivel Leveler Threaded Stem Glide with metal base. Thread is 3/8-16, Base Diameter is 1 1/4" and the stem length is 1 1/2". This glide screws into a 3/8" threaded leg hole to put a selected height. Use this product to stop wobbling on an uneven floor. 

LCN Door Closer Hold Open Arm

Adjustable nut allows door closer arm to lock when the preselect position is reached.

Specify your current closers model number when ordering.
Not all of the LCN closers have the same shape spindle on the door closer
cylinder. The LCN Part #'s on this Regular Arm is: 1260-3049, 1460-3049, 4010-3049, 4020-3049, 4040-3049

Provides hold-open function with templated stop/hold-open points.
Handle controls hold-open function.

Specify your current closers model number when ordering. Not all
of the LCN closers have the same shape spindle on the door closer
cylinder. This LCN Arm is known as these part numbers: 1260-3049CNS, 1460-3049CNS, 4040-3049CNS, 4110-3049CNS

Handing diagram

LCN Door Closer Spring Cush Hold Open Arm 3049SC

Optional, parallel arm for abusive applications features solid forged steel main arm and forearm with spring loaded stop in the soffit shoe. Handle controls hold-open function.

7/8" diameter Nylon based Nail On furniture glide. Protect hardwood, ceramic tile, linoleum & hard surfaces from mars & scratches by using this nail on glide.

The ALREX hinge is a full function hydraulic door closer hinge. It contains all the features of a door closer, closing and latching speed control, power adjustment, and optional hold open feature. They are available in 4, 4.5 and 5 inch (leaf height), and are currently available in Stainless and Black finishes.

Package includes 2 hydraulic closer hinges and one dummy, for a standard 3 x 7 foot door, 100 pound door.

Door Handing:

Glynn-Johnson 81 Series Overhead Door Holder Surface Mounted

Glynn-Johnson 81 series holders and stops provide rugged, heavy-duty door control. The jointed-arm design provides the most effective stop mechanism available. The shock absorber bracket is surface mounted, usually with sex bolts. The jamb bracket is mounted to the stop of the frame, so a minimum of door and frame preparation is required.

GJ80 Catalogue

Metal Swivel Glide with 3/4" chair leg O.D. X 9/16" I.D. chair leg  With Ferrule. American Seating and Griggs Metal Base Swivel glide with internal holding clip. Base is 1 1/4" in diameter. Metal base glides are very popular in schools and institutions and move easily across smooth or carpeted floors.  Metal base glides are nickel plated and are extremely durable, but when they do wear out, they will scratch the floor.  The glide freely swivels beyond 30 degree angle. Glide grips leg with outside holding clip, meaning it grabs the outside of the leg, see more views for picture of outside holding clip. 

Metal based glide that nails into wooden furniture, 1 1/8" diameter base glide. .

Partition Surface Mounted Stainless Steel Slide Bolt Latch 1-7/8" Screws. Stamped stainless steel construction. Base is 2-7/8" high by 1-3/8" wide by 5/32" thick. Latch bolt is 2-1/4" long x 13/16" wide x 1/8" thick, and the slide distance is 25/32". Also known as a Bathroom Stall Stainless Steel Slide Latch and Toilet Partition Locks. Manufacture part # 6309. Shipped with mounting screws.

• Available (NHO) non-hold open,
(SHO) selective
hold open. Specify degree (90, or
105°)
• Standard top pivot: 180 included
• Cycolac cement case
• Separate independent valves for closing,
latch and backcheck adjustments
• Built-in positive dead stop prevents door
from swinging beyond the desired
opening degree
• Vertical door adjustment

Less all parts means, only the Cylinder!

Norton / Yale Door Closer Hold Open Parallel Bracket

Replacement bracket works with the Norton 1600, 9300, 7500, and 8000 series, along with the Yale 50, 3000, and 4400 series hold open closers.

Norton Part # 1628H
Yale Part # 588

Swivel Glide 9/16" O.D. X 7/16" I.D. W Ferrule-Nylon Base. Measurements are for the chair leg. Heywood Wakefield replacement chair feet with nylon base. Base is 1 1/4" in diameter. Metal base glides are very popular in schools and institutions and move easily across smooth or carpeted floors.  Metal base glides are nickel plated and are extremely durable, but when they do wear out, they will scratch the floor.  The glide freely swivels beyond 30 degree angle. Glide grips leg with outside holding clip, meaning it grabs the outside of the leg, see more views for picture of outside holding clip. 

Center Hung Door Closer

• Available (NHO) non-hold open, or (SHO) selective
  hold open. Specify degree (90 or 105°)
• Standard top pivot: 340 included
• Cycolac cement case
• Separate independent valves for closing,
  latch and backcheck adjustments
• Built-in positive dead stop prevents door
  from swinging beyond desired opening
  degree
• Vertical and horizontal door adjustment
• Arm centering adjustment

Square Leg Metal Swivel Glide with a 1-1/16" base diameter. This Chair Glide does not have ferrule. This swivel glide is for a square tubing chair leg with a 7/8" outer diameter and a 3/4" innner diameter. 

Metal Swivel Chair Glide with a 11/16" O.D. X 9/16" I.D. W/O Ferrule. Measurement is the chair leg diameters.  Used as a replacement for the American Seating glide, used on the Alert Line chairs. This chair glide has a 1 1/4"  metal base diameter. The clip at the top holds the glide on by going inside the leg.  

Swivel Glide for a Square tubing Leg  chair with a 1" O.D. X 7/8" I.D. 1 1/16" base diameter. This glide does not have a ferrule. 

Dorma RTS88 Series overhead concealed door closer for both
single and double-acting doors. The RTS88 will consist of a steel
cam, rollers, and springs housed in a compact cast iron body.
Closers will be capable of being installed in minimum 1-3/4" x 4"
headers. RTS88 will have maximum door opening to 90º or 105º,
trim conditions permitting. Sweep and latch speed will be
controlled by two noncritical adjustment valves from 90º or 105º
to closed. Built-in pressure relief valve will protect the closer from
abuse caused by forced closing. A mechanical backcheck
combined with a positive stop at 90º or 105º will be provided to
protect the door and frame. The RTS88 closer will be available
with hold open at 90º or 105º, or without hold open. The product
shown here is just the replacement cylinder.

Adjustable Height Swivel Glide, Nickel Based for chair legs with a 5/8" outer diameter and a 1/2" inside diameter. The base of this glide is 1 1/4" in diameter. This glide helps level uneven chairs. 

Norton and Yale Hold Open Loop Assembly

This part is the part that always breaks on the Norton and Yale Friction Hold Open Arms. Cast Iron Construction, powder coated to the desired color.

Norton Part # 7701-13
Old Norton Part # 1620-13
Yale Part # 400-13

Norton CloserPlus Non Hold Open Arm

This heavy duty Parallel Arm can be used with the Norton 1600, 9300, 8000 and 7500 door closers.

Aluminum is in stock, Dark Bronze is 2-3 week lead time.
Norton Part # 6770-5

Corbin Russwin Hold Open Arm

Friction hold open arm.

Corbin Russwin part # 688F77

Nylon based Metal Swivel Glide for a round chair leg with a 1-1/8" O.D. X 1" I.D. This glide does not have a ferrule. This glides base is 1 1/4" in diameter. Metal Furniture Feet for school and institution applications. Nylon base protects your floor as long as the bottom does not have grit and grime on it. 

Metal Swivel based Chair Glides for Heywood Wakefield Chairs. This Chair glide is used on a round tubing chair leg with a  9/16" O.D. x 7/16" I.D. This glide is With Out a Ferrule. The base of this glide is 1 1/4". This glide has a clip that holds the glide on by going inside the chair leg. 

Chrome Plated Slide Bolt Latch 9/16" Bar To Door Clearance

Zamac die cast construction with polished chrome plating. Base is 3-3/8" high with 2-5/8" hole spacing. Latch bolt is 3-1/8" long by 7/8" wide by 3/16" thick with a 9/16" dimension from the door to the under side of the latch bolt. The latch projects out 1-1/2" when installed on the door. Also known as a Bathroom Toilet Stall Door Slide Latch and Toilet Partition Locks. Manufacture part # 6540.

Shipped with mounting screws.

• Surface Bolt has 1-3/16" throw for maximum security.
• Strong tension springs prevent creep.
• Ideal for all types of doors.
• Available 8"
• Units packed with standard screws for added security.
• Units packed with both a universal top strike (US) and
a mortise bottom strike (MS).
• Constructed of heavy duty steel.

Sargent Hold Open Arm

Sargent part # 25-H

Metal Based Swivel Glide for round tubing.  9/16" O.D. X 7/16" I.D. With Ferrule. Heywood Wakefield replacement chair feet. Metal chair foot with a 1 1/4" diameter base. Metal base glides are very popular in schools and institutions and move easily across smooth or carpeted floors.  Metal base glides are nickel plated and are extremely durable, but when they do wear out, they will scratch the floor.  The glide freely swivels beyond 30 degree angle. Glide grips the inside of hollow legs with a holding clip, meaning it grabs the inside of the leg.

Norton 8301 Door Closer, Sometimes called the Norton 8301 Omni Door Closer

• Adjustable spring sizes 1 thru 6
• Rack-and-pinion design
• 1-1/4" (32mm) diameter piston
• 5/8" (16mm) diameter pinion journals
• Cast aluminum body
• Standard, separate and independent, latch,
  sweep and backcheck intensity valves
• Staked valves
• Molded plastic cover standard

This closer replaces the 8301BF Norton Door Closer. The standard 8301 now meets the Barrier Free Requirements.

Glynn-Johnson 90 Series Overhead Door Holder Surface Mounted

Glynn-Johnson 90 series holders and stops are the most rugged models available for heavy-duty applications. The channel is surface-mounted to the door, most often with barrel nuts, and the jamb bracket is surface mounted to the jamb, requiring minimal door and frame preparation.

GJ90 Catalogue