Search results for: 'ghost 8 down braced door hider'

Full Mortise Double Acting Spring Hinge

Used mainly for commercial kitchen doors,  or any commercial double swinging door.   Sold in sets of 2 hinges, they will handle doors up to 75 lbs that are 1-3/4" thick.   If you door weighs between 75 and 107 lbs, you should use 3 hinges.  The door flange is designed for a standard 4-1/2" x 4-1/2" template mortise.   Hinges ship with wood and metal mounting screws. They come in a standard Painted Primed Finish Gray.

Exterior or Interior Doors
Weight to 500 lbs.
Door Sizes up to 3'8"x 8'6"
Includes 340 top pivot
Non-handed

Concealed Latch Fix it Kits for Plastic Laminate Doors

For 1" Thick Doors- Square Edge for Plastic Laminate
All Hardware included

Roval Recessed Paper Towel Dispenser, 20452 Dispenses 600 C-fold or 800 multi-fold paper towels. Door fabricated of 18 gauge type 304 drawn one piece stainless steel with satin finish. Door secured with 3/16" staked piano hinge and flush tumbler lock. Wall Opening: 11 3/16" W x 26 1/4" H x 4" D

ASI Matte Black Horizontal liquid soap dispenser is surface mounted and holds 40 oz of soap. Unit offers tamper resistant refill indicator and bush buton dispensing. Refill manually using hinged door at top with special key(included). The product is stainless steel with a matte black powder coated finish. With a matte black finish this product offers a more sophisticated and bold look while being aesthetically appealing to the eye.

Dimensions

The Jackson 1095P Paddle Exit Device is designed for use on narrow style aluminum storefront doors.  It features the same housing as the Jackson 1095, but with a paddle instead of a cross bar.  This peice is designed for aluminum or steel doors, it will not work on wood doors.   The device mounts on surface studs that need to be drilled and tapped on the door, if the door is wood, the threads will simply pull out.

The Von Duprin 100316 is used on the 5547 on the top of the door.   The top rod goes through the square hole on the plate.  The plate shown in the Picture has both sides or LHR and RHR doors.  One side of the strike is usually broken off depending on the hand of the door.

Push Plate 70

.125" thick with 4 beveled edges. Base material is either aluminum, brass, bronze or stainless steel depending on the finish. This would be considered a premium push plate.

Finishes

Toilet Partition Continuous Hinge 54" With Cam Close Stainless Steel. The hinges must be mounted flat when door is shut. For inside swing the hinges are mounted on the inside of the stall. For the outside they must be mounted on the outside.

Stainless Steel Construction, 14 gauge (.075" thick). Hinge is 3" wide when laid flat, by 54" long. Holes are spaced every 13" and are 9/32" diameter and 5 sets of holes. The hinge is self closing by a cam action, which is made possible by angle cuts on the continuous hinge leafs. Cam features Zero Degree Closing. Can be raised up 3/8" for emergency entry. This hinge is also known as a Bathroom Stall Full Length Continuous Hinge. This hinge is non handed. Manufacture part # 130209, 7599, 125319, 650-9402. This hinge is known as 7599.

The Aluminum Bleacher End Cap is also known as Part #P7002N.

Note: We offer 7½" (P7002na), 9½" (P7002nb), and 11½" (P7002nc) width for Aluminum Bleacher End Caps. They are 1¾" thick and feature 2 bends of 1⅛" & ⁹⁄₁₆". The Aluminum Bleacher End Cap includes self taping screws. Please select the appropriate size from the dropdown menu below.

This aesthetically-pleasing Aluminum Bleacher End Cap is designed to provide a clean and finished look to your aluminum bleacher system. Made from high-quality materials, these Aluminum Bleacher Ends ensure longevity and resistance to wear and tear, making them an ideal choice for schools, sports facilities, and outdoor events.

The Aluminum Bleacher End Cap is easy to install, fitting securely onto the ends of your bleacher rows. Its sleek design not only enhances the overall appearance of your seating but also helps to prevent debris from entering the bleacher structure, maintaining a tidy environment.
Whether you're upgrading existing bleachers or installing new ones, the P7002N End Cap is a reliable solution that combines functionality with aesthetic appeal.

Consider implementing a cleaning and maintenance schedule to keep your bleachers looking their best. A clean and well-maintained environment not only enhances the aesthetic appeal but also contributes to the longevity of the materials. Simple tasks like wiping down surfaces and removing debris from the Aluminum Bleacher End Caps can make a significant difference. Whether it's comfort, accessibility, or safety concerns, replacing worn-out Aluminum Bleacher End Caps with new ones can help you prepare for future upgrades or changes involving your bleacher systems. By prioritizing maintenance, safety, and user experience by installing new Aluminum Bleacher Ends, you can ensure that your bleacher system remains a dependable and welcoming space for all events.

Please feel free to contact us for assistance with ordering the correct replacement Aluminum Bleacher End Caps for your specific needs. We are always glad to help you choose the best options for your bleacher systems. Order yours today!

Yale 7100 Exit Device

Door Opening Width:
-36 for 30" - 36" (762 - 914mm) doors
-48 for 36-1/2" - 48" (927 - 1219mm) doors
Door Thickness: 1-3/4" (44mm) standard.
Minimum Stile Width: 4-1/2" (114mm)
Projection: 3-1/4" (83mm) active, 2-3/4" (70mm) dogged
Latchbolt: 3/4" (19mm) deadlocking stainless steel Pullman-type
Strike: 757 (panic),

Automatic Floor Type Holder and Stop

Cast brass construction, and then chrome plated. Measures 3-11/16" high by 3" wide with a 1-15/16" projection. The strike is 1-3/16" high. Spring loaded brass roller, rolls over the the strike to lock the door in the open position. To release, just give the door a tug.

Interior Doors
Weight to 200 lbs.
Door Sizes up to 3'6"x 8'6"
Includes 320 top pivot
Non-handed

• For 1-3/4" (44mm) doors standard
• Through-bolted with 3 mortise nuts
• Pulls project 1-1/2" (38mm) from door face
• GTB Design trim will cover a 161 cutout

Interior Doors
Weight to 250 lbs.
Door Sizes up to 3'6"x 8'6"
Includes 320 top pivot
Non-handed

Lyon Metal Locker Two Person Latch Bar, lh. Used for upper latching doors.

1975 to present 17" length.

Replacement LCN 4640 (4642) Door Closer Arm. Arm is Non handed and ships with screws.

LCN Part # 4640-3077

Ives Roller Bumper Offset Ives RB470

RB471
Features:

• Constructed in heavy-duty cast brass.
• RB470 used where two doors open against each other to prevent damage

to the doors or hardware.

• For automatic closing of doors
• Packed with wood and metal screws

This hinge is not recommended for doors that have a sweep larger than 110 degrees.

Sold in Boxes of 3 Hinges
Shown in brushed brass

Occupancy Indicator Latch Handle is constructed of cast stainless steel with a satin finish. Latch handle is designed for 3/4" Doors and is through mounted to the occupancy indicator. Features a 4-1/2" length handle that is tapered at one end to engage with keeper for locking. Features emergency unlatching access on front of indicator. Shipped with fasteners for mounting occupancy indicator to door and pilaster. Known as manufacturer part number 4993. 

Application
includes 180 top pivot
Interior Doors
Weight to 300 lbs.*
Door Width up to 3'6"(1067mm)
Handed

Handing diagram

• For 1-3/4" (44mm) doors standard
• Through-bolted with 3 mortise nuts
• Pulls project 1-1/2" (38mm) from door face
• GTB Design trim will cover a 161 cutout

ASI Matte Black Vertical liquid soap dispenser is surface mounted and holds 40 oz of soap. Unit offers tamper resistant refill indicator and bush buton dispensing. Refill manually using hinged door at top with special key(included). The product is stainless steel with a matte black powder coated finish. With a matte black finish this product offers a more sophisticated and bold look while being aesthetically appealing to the eye.

Dimensions

Concealed Latch Fix it Kits for Powder Coated Steel

For 1" Thick Doors- Round Edge for Powder Coated Steel
All Hardware included

Concealed Latch Fix it Kits for Powder Coated Steel

For 1" Thick Doors- Round Edge for Powder Coated Steel
All Hardware included

C-Fold, Multi Fold Towel Dispenser and Waste Receptacle
22 gauge Type 304 Stainless Steel
Heavy duty door and piano hinge
Tumble lock on doors and waste receptacle
600 C-fold or 800 Multi-fold towel capacity
12 gallon waste receptacle
h15"w x 54" x 4"d hole opening
17-1/4"x56"ht x 4" overall dimension.

Ordering Online All Plastic Laminate Floor Mounted Screen Manufactured by Global Partitions, see color chart below. For other factory colors please call for pricing. All toilet partitions ship in 1 week, 3-4 days travel. 6"x70" pilaster, _ _ x 58"ht panel and all standard hardware included. 16", 18", 22", 28", 34", 40", 46", 52", 55", 58", 60", 65", 70" and 76" panels available, note panels are 1/2" less than width size.

Global Plastic Laminate color chart

Hold Open Cushion Arm for the CRL PR90, Cal-Royal CR441 and International 44CI door closers.  For use in parallel arm applications only, T Handle locks the door in the open position.

Bobrick slide latch for surface mounting on doors. Most common with Bobrick's doors. Also known as 1040-42 or 1001492 includes latch track, latch cover, set screw that uses a 5/64" allen wrench and flathead latch screw.

• For standard weight doors
• Low frequency usage
• Packed with wood and metal screws
Not for use with a door closer.

Sold in boxes of 3
Shown in brushed brass

Von Duprin 9827/9927 surface mounted vertical rod device for all types of single or double doors, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1. Covers stock hollow metal doors with 86 or 161 cutouts. The Von Duprin 9827 device has a smooth mechanism case and the Von Duprin 9927 device has a grooved case. The surface vertical rod device is non-handed.

Cal Royal 2000 Series Exit Device Lever Trim

Non-handed Grade 1 (Clutch Style)
Cylindrical body hardened steel heavy duty tailpiece. For
1¾” and 2 ¼” doors. Prefix THI before part # for 2 ¼” door
thickness. Available for fire and non fire rated rim and
vertical rod exit devices.
Rose diameter 3 ½”, lever length 4 ¾”.

The Adams Rite EX88 Interlocking Rim Exit Device is designed for heavy duty use on narrow stile aluminium door applications. The EX88 has a unique latch bolt design that interlocks with the frame of the door. This device is non handed, requires a minimum stile width of 2" and will work on aluminum, hollow metal or wood doors.The device is constructed of extruded aluminum with matching metal angled end caps. To order specify your door width, and the color.

Concealed Latch Fix it Kits for Plastic Laminate Doors

For 1" Square edge for Plastic Laminate
All Hardware included

Penco Locker Bottom Cam Assembly for double door lockers.

Stainless Steel global slide latch with indicator and emergency access. Overall dimension 2-3/4" x 1-1/2" with 2-1/4" hole spacing. Used with new style doors 10/1/21 to current. Used with a 1 inch door. Security screws included. Manufactures part number 40-8263010.