Search results for: 'closers latches taxable tips acrylic spic'

Truth Telescoping Pole

Telescoping Pole with Hex Ball or Hook Drive
Rigid anodized aluminum poles feature free-turning ABS hand grips.
6 foot pole extends to 10 feet.

Truth Part # 10637 Hex Drive
Truth Part # 10638 Hook Drive

5/32" Dog Key used on old Von Durpin, and Dor-o-Matic exit devices. This key has the longer shaft to fit into the deeper Von Duprin dogging slots.

5/32" hex key

3-1/16" overall length

Doromatic PS914x900-2RS Power Supply

Doromatic 2390 Fixed Cover

The Doromatic 2390 Fixed Cover also known as the center case cover. The cover is 1-1/2" wide by 3-7/16" high and projects out 2 inches. The mounting screws are 3" on center.

Doromatic / Falcon Part # COVER.127 or PB341

Truth Nylon Tie Bar Guide 41157

This nylon guide is used when you have multiple sash locks on your window.  Inside the window, or sometimes on the surface these  nylon guides keep the connecting rods in place, so you only have to actuate one lock to lock multiple locks.

Truth Nylon Tie Bar Guide 45141

This nylon guide is used when you have multiple sash locks on your window.  Inside the window, or sometimes on the surface these  nylon guides keep the connecting rods in place, so you only have to actuate one lock to lock multiple locks.

Monarch 25-R Series Center Case Cover Kit

Replacement cover for the Monarch Falcon 25-R Exit Device.   Kit includes cover and the mounting screws.

Falcon Part # 650255

The Dor-O-Matic Falcon Request to Exit Switch, SWITCH.1006 is for use on the 1690, 1790 and 2390 devices, produced after June 2002.  The Request to Exit Switch allows you to cut the current to various devices when the push bar in depressed.

Installation Instructions

Dorma 8400 Surface Vertical Rod Exit Device minimize forced entry while offering a low-cost solution to life safety requirements. Certified/listed to ANSI/BHMA 156.3 Grade 1 for exit devices. 5 year limited warranty.

Yale 7000 Series End Cap

Yale Part # ECK7

Newer impact resistant end cap. Replaces all of the older version end caps for the Yale 7000 series.

Shown in stainless steel.

Stainless Steel Torque Head Barrel Nut Shoulder Screw for 1-3/16" - 1-3/8" gripping. Use with torque driver bit T27 for toilet partition security screws. 10-24 thread stainless steel unplated and uses a 6 lobe head torque. Both pieces included.

The Truth 11577 is used on the Encore and Maxim Awning Operators, Models Wi5100 (51.00) and Wi5110 (51.10). The operator is attached to the track by the 11647 Slide Shoe. The track measures 16 inches long by 5/8 inches wide and 5/16 inches deep.

5/16" Spline Window Operator T Handle.

Replace regular crank handles with this compact T handle. Also known as a Butterfly Handle.

Application
Interior Doors
Weight to 250 lbs.*
Door Width up to 3'6"(1067mm)
Includes 180 Top Pivot
Handed

Handing diagram

Exterior or Interior Doors
Weight to 600 lbs.*
Exterior Door Width up to 3'0"(914mm)
Interior Door Width up to 3'6"(1067mm)
Includes 180 Top Pivot
Handed

Handing diagram

Sargent 3828 Series Exit Device

The 3828 is a rugged exit device in a rim design. The 3828 Non Configured Rim Exit Device has 7 functions, 4 available trims and is easy to mix and match the device and trim. Aluminum finish only.

Von Duprin Exit Device 992L Hex Stud

This is the Hex Stud used on the 992L Lever Trim and the 991K Knob Trim. The threads are 1/4-20. Overall length is 1-3/4".   Later versions of the 992L had a larger thread size.

Von Duprin Part # 971440

Truth 11.43 Awning Operator

Arms are 8-3/8" long, and measures 20-3/4" across when the arms are in the closed position.

Awing Operator, we usually find 31545 stamped on the arm, they used to be a cadmium plated steel, now they are powder coated. We also find 21221 on it.

Rixson 27 Series Bottom Arm Package 252050

This kit included the Arm Cap & Screw, Offset Arm, Arm Shim, Arm Bearing Washer, and Spindle Shouler Collar.

Rixson Part # 252050

Awning Operator Guide Bar 30568

The Truth Operator Guide Bar measures 26-3/4" long with the two mounting holes at 26-1/8" on centers. The bar is constructed of extruded aluminum. The Wi10005 is the component that slides in this track. This track is mounted to the sash.

Truth Part # 30568

The TH1300 YKK Offset Pivot Set is commonly found on YKK aluminum framed storefront doors. This is not the only one they use, but the only one we can get.

Marsh 24' Roll Cork Insert for 2" map rail. The cork insert measures 1-1/2" high by 1/4" thick by 24' long. Replacement cork only, specify Tan or Gray

Swivel Based Chair Glide for round tubing with measurements of 7/8" O.D. X 3/4" I.D. This chair glide does NOT feature a Ferrule, This glide has a clip that holds the glide on by going inside the chair leg. The Chair Glides Base diameter is 1 1/4". 

Surface Mounted Hinge Set Lh Out, Rh Inswing Chrome Plated

Also known as a Bathroom Stall Gravity Hinge Set.
Self closing hinge set.
Cast brass construction with a polished chrome finish.

1-1/2" hole spacing up and down 2-7/16" right to left hole spacing.

Lh Out, Rh Inswing

Shower Room Pedestal 8" x 16-1/4"ht Sold Individually. Heavy duty Bench Pedestals shall consist of steel tubing with 10 gauge steel flanges welded to each end. The overall height of pedestal shall be 16-1/4". Pedestals are to be finished to match the lockers in  Putty color.

This rectangular folding shower seat is 18 inches by 16 inches with a wood-grained phenolic one-piece top.  Tubular components are fabricated from stainless steel.  The shower seat has a self locking mechanism to secure the seat upright when not in use. When properly mounted seat will support up to 250 lbs.

Casement Window Handle-2-3/8"

The hole spacing is 2-3/8" between screws and has a 1/2" lock up (distance between inside of cup to back of handle). Cast white bronze with a brushed nickel finish.

Right hand shown

1714mkada Master Lock

• 5-Pin Tumble key
  
• Built in key locks, Bolt moves Horizontally.
  
• Comes with 2 user keys.
  
• Automatic locking springbolt.
  
• For box lockers
  
• Right or Left Hinged
  
• Master Keys extra, We will need your master key number if adding to your existing system.
• 1-2 week lead time

Toilet Partition Continuous 'L' Wall Bracket 2-3/4" X 57-1/2" Aluminum

Extruded aluminum construction. Base is 1-3/8" and the leg projects out 2-3/4". These are sold individually. It is also known as a Bathroom Stall Continuous L Wall Bracket. The manufacturers part # is 2684.

The Matte Black Hadrian Anchored Pilaster Shoe is constructed of stainless steel. Designed so that the shoe anchors directly to the ground and the pilaster sits inside. Is for 3/4" thick Pilasters and is 3" in height. Shoes come with fasteners to install and is available in different lengths.

Lyon Metal Tamper Guard Locker Handle Assembly for right handed lockers, facing the locker if the hinges are on the right side then they are a right handed locker. Assembly includes case, lift and 1 screw. Used in September 1981 to Current. Also known as 6781and 6782, 75011, ly2232, ll1741.

Global Top Hinge Pin For Laminate Partitions

Threaded steel construction. The top pin measures 3/8" diameter by 3-1/4" long with 5/16-18 threads. It has a screw driver flat slot on one end. Also known as a Bathroom Stall Door Top Hinge Pin. Manufacture part # 98584.

Bobrick Partitions Pintle 5/8" Diameter

Steel and white nylon construction. The Pintle is 5/8" diameter by 2-1/4" overall length with 5/16-18 threaded end. Also known as a Bathroom Stall Bottom Pintle 5/8" Medium Lift. Manufacture part # 98175.

Shipped with nut and lock washer.

Ives Roller Bumper Straight Arm 6" Ives RB472

Features:

• Constructed in heavy-duty cast brass.
• RB472 is ideal for use in situations where doors meet each

other at approximate right angles (back to back).

Exterior or Interior Doors
Weight to 450 lbs.*
Door Width up to 4'0"(1219mm)
Includes 180 top pivot
Handed

Handing diagram