Search results for: 'brush changing strip'
-
International 8730S Narrow Design Surface Vertical Rod
The International Door Closer 8730S is designed for narrow stiles. The minimum stile width is 2-19/32 inches. It will not work on a true narrow stile door witch is usually 1-3/4 inch. The 36 inch version is 33-15/32 inches and the 48 inch version is 44-3/4 inches. The device is rated Grade 1, which is the highest rating. Rods are 1/2 inch diameter tubular with rod guides. The exit ships will all screws and strikes need for instillation.
8730S- -
A.W. Anderberg 201ST 4 Bar Window Hinge
A.W. Anderberg 201ST 4 bar window hinge, cadmium plated steel construction.
Usually found on light commercial or residential buildings with hopper windows. This hinge is being discontinued, and replaced by the 201SS Hinge, which has the same hole spacing, length, and stack height.
23/32" track width x 1/2" stack height.
If you have a casement window with a 16" track length, please see 222SS Egress Window Hinge.
Sold individually, these hinges are non handed, we recommend that you change both hinges when you are replacing them.
201ST-XX -
Rixson 147 Pivot Set
Exterior or Interior Doors
Weight to 600 lbs.*
Exterior Door Width up to 3'0"(914mm)
Interior Door Width up to 3'6"(1067mm)
Includes 180 Top Pivot
Handed147 -
Aluminum Nosing 2 inch with Grit Surface
This 2-1/2" deep nosing is made from the same material as our Grit-Surface Aluminum Treads. The front edge is 1-3/4" deep (inside nose dimension is 1-1/4"). The nose has a 1-3/4" wide abrasive finish with a 3/4" tapered aluminum back edge. Both the nose and tapered edge have a 1/4" wide reflective yellow safety tape strip for additional safety. The nosing is available in abrasive colors of Black, Brown, Blue, Gray, Green, Red or Yellow. Nosing is available solid (for glue-down applications) or with countersunk holes (for screw-down applications) every 12". Nose drops 1-1/16".
SPECIFICATIONS:
Furnish and install Musson Grit-Surface Aluminum Nosings, 3/16" thick X 2-1/2" deep; cut lengths up to 10 foot long. Tread surface shall have aluminum oxide abrasives permanently bonded to a heat treated aluminum nosing with 1/4" wide reflective yellow safety strip on both the top surface (between the grit surface and aluminum) and the nose. Grit surface shall be in one of the following standard colors: Black, Brown, Blue, Gray, Green, Red or Yellow. Nosings can be supplied with two countersunk holes every 12" for screw down installation or without holes for installation with our #400 Neoprene Contact Cement.
Custom sizes are available up to 10' long
GSA2N- -
Reinforcing Pivot Hinge
The reinforcing pivot hinge is a good way to solve door sag issues. And also be a preventative solutions for future isses with extra heavy or wide doors. The hinges comes in two sizes 4 or 4.5 inches, and two finishes, prime coat and satin chrome. The hinge uses a heavy duty ball-bearing to add extra life. The base metal is steel.
GBB85 -
Rixson 195 Pivot Set
Exterior or Interior Doors
Weight to 450 lbs.*
Door Width up to 4'0"(1219mm)
Includes 180 top pivot
Handed195 -
Wood Door Automatic Flush Bolt FB41
Wood Door Automatic Flush Bolt FB41
H.B. Ives FB41 Series are sold has Top, Bottom or in Pairs (top and bottom). Fully automatic, inactive door is latched when active door closes, bolts retract when active door is opened. Top Bolt has no spring tension. They are non handed, but the top and bottom bolts are different. The body size is 1" wide, 8-1/2" tall and 2" deep, the bolts have a 3/4" throw with a 7/8" vertical adjustment.
Ives Part #'s
FB41P - Pairs
FB41T - Top
FB41B - BottomFB41- -
Door Pull 11
Door Pull 11
This door pull has 8" center to center screw spacing. The base is 3/4" diameter, the overall lenght is 9-1/4". The projection is 2-1/8" and the clearance is 1-1/2". Also known as a 8" Center Door Grip or Door Handle. This handle is shipped with thru bolts and finish washers.
Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.
GHE11- -
Von Duprin Exit Devices 608/696/880/990 Trim Grip
Von Duprin Exit Devices 608/696/880/990 Trim Grip
Replacement Grip/Handle only, screws not included. Cast bronze construction, and then plated to the selected finish. The Grip measures 15/16" wide by 6" long. The center to center hole spacing is 5-1/2". This handle works on the Von Duprin 608, 696, 880, and 990 outside trim plates.
Von Duprin Part # 972466 and 972467
Old Part # 969925 and 959122G972466- -
A.W. Anderberg 201SS 4 Bar Window Hinge
A.W. Anderberg 201SS 4 bar window hinge, stainless steel construction.
Usually found on light commercial or residential buildings with hopper windows.
23/32" track width x 1/2" stack height.
If you have a casement window with a 16" track length, please see 222SS Egress Window Hinge.
Sold individually, these hinges are non handed, we recommend that you change both hinges when you are replacing them.
201SS-XX -
International 8710S Narrow Design Rim Device
The International Door Closer (IDC) 8710S is a narrow design rim device. The minimum stile width has to be 2-19/32 inches. The device features a 3/4 inch throw deadlocking latchbolt, hex key dogging, and ships with machine screws and strike. The device is Grade 1 Rated, which is the highest rating possible. The 36 inch device is 33-15/32 long and the 48 is 44-3/4 inches.
8710S- -
A. W. Anderberg 301ST Window Hinge
A.W. Anderberg 301ST Cadnium Plated Steel HInge
Usually used on commercial hopper windows. If you have a Casement Window, please see the 222SS or the 333SS Egress Window Hinges. This hinge has been discontinued, and is replaced by the 301SS hinge, which has the same hole spacing, length, and stack height.
29/32" wide x 5/8" stack height
Sold Individually, these hinges are non-handed. We recommend that you change both hinges when replacing.
301ST-XX -
ALREX Door Closer Hinge
The ALREX hinge is a full function hydraulic door closer hinge. It contains all the features of a door closer, closing and latching speed control, power adjustment, and optional hold open feature. They are available in 4, 4.5 and 5 inch (leaf height), and are currently available in Stainless and Black finishes.
Package includes 2 hydraulic closer hinges and one dummy, for a standard 3 x 7 foot door, 100 pound door.
Door Handing:
AX21 -
Von Duprin 55 End Case
The Von Duprin 55 End Case is the housing on the hinge side of the door. The function of this housing is to lift the cross bar, and support the function of the Active Case. If your housing is on the right side when standing inside looking out, then you would order the Right Hand Case. The package includes the housing, springs and back plate, the arm is not included. The current part number on this part is 050196 and 050197, the old part number is 111931 and 111932.
55R30
