Search results for: 'groov 8 delux base door hold'

For Hussey Bleacher 5" Wheel Axle. Overall dimensions are 3/8" axle x 2-5/16" length. 2-1/16" between grooves. This axle is also used with Folding bleacher Company. Includes clips. Also known as 1001133.

Partition Slide Latch 3/8" Bar To Door, 2-3/4" Between Screws Stainless Steel

Cast stainless steel construction. Latch base is 4" high with 2-3/4" hole spacing. Latch bolt is 3-3/4" long by 3/4" wide by 3/16" thick. The latch bolt clearance is 3/8" from the back of the base to the under side of the latch bolt and projects out 15/16". The latch projects out 1-9/16" from the face of the door when installed. Also known as a Bathroom Stall Surface Mounted Slide Bolt Latch and Toilet Partition Locks. Manufacture part # 5033.

Shipped with mounting screws.

Sled Base Felt Stem Glide with a 1/4" insert diameter. The base diameter is 7/8" and the Stem Length is 1/2". This glide works on any diameter sled base chair. This glide gently taps into 1/4" hole on the bottom side of a sled leg. Felt bottom to help protect floors. 

LCN 4040XP-CUSH Door Closer

The same 4040XP Door Closer with the CUSH (Non Hold Open Cush) arm or 3077CNS arm.

• • Strongest Pinion Ever - At 3/4”, It’s The Super Hero Of Pinions
• Taller Bearings - 5/8”, Real Muscle Against Forced Openings And Closings
• An Overall 44% Increase In Maximum Load Capacity
• Tougher Teeth - Fight Wear And Tear
• V-Shield Seal With 20% Longer Life
• Better Wear Resistance From Sagging Doors And Warped Frames
• XP = eXtra Protection In Real-World Applications

We ship the 4041XP-CUSH

1/4-20 thread Leveler swivel nylon base glide. Stop wobbling of uneven floors with this Metal Furniture Foot.  1 1/8" base diameter and 1 1/8" stem length. Screw into a thread leg hole to reach your desired height. Combine with a tnut to install in wooden furniture legs. 

Norton Door Closer Rod and Shoe

The Norton Rod and Shoe 7701-11 and 7701-11A come in two different lengths, 8-7/8" anc 12-1/2".  The length is measured from the end of the bar to the center of the eyelet.

Norton Part #'s:
8-7/8" Long  7701-11
12-1/2" Long 7701-11A

Leveler Glide with Metal Swivel Base. 1/4-20 thread metal base swivel glide. Stops the wobble of an uneven floor. 1 1/4" base diameter and 1 1/8" stem length. Can also be used with a t-nut to install in wooden legs. Use a spring clip to install in hollow legs. 

LCN Door Closer Head and Tube

The LCN Door Closer Head and Tube comes in two versions.  One is 5-3/4" long and the other is 8-5/8".  The square hole is 5/8",   This part usually goes by the part number 4040-78H, 4040-78HL, 1260-78H, 1260-78HL, ect.,.

The 4040SE Sentronic® is a heavy duty, non-handed, nonsized closer/holder designed to provide single point hold-open for fire and smoke barrier doors. The door is held open until current interruption releases the
holding mechanism and the door closes. Single lever (track) arm closer is specifically designed for interior doors. Choice of finishes, track functions, and installation accessories meet virtually all life safety requirements.

Glynn-Johnson 79 Series Overhead Door Holder Surface Mounted

Glynn-Johnson 70 and 79 series models are constructed primarily of Brass and 300 series Stainless Steel substrates, with several components fabricated of Steel treated to resist corrosion. Models in the 70 series utilize a 1/2"-diameter stainless steel bar, while the 79 series uses a 3/4" stainless steel bar. The bar is always provided in US32D. The spring, washer and nut are provided in a clear zinc finish.

GJ70-79 Catalogue

Partition Surface Mounted Stainless Steel Slide Bolt Latch 1-7/8" Screws. Stamped stainless steel construction. Base is 2-7/8" high by 1-3/8" wide by 5/32" thick. Latch bolt is 2-1/4" long x 13/16" wide x 1/8" thick, and the slide distance is 25/32". Also known as a Bathroom Stall Stainless Steel Slide Latch and Toilet Partition Locks. Manufacture part # 6309. Shipped with mounting screws.

Glynn-Johnson 70 Series Overhead Door Holder Surface Mounted

Glynn-Johnson 70 and 79 series models are constructed primarily of Brass and 300 series Stainless Steel substrates, with several components fabricated of Steel treated to resist corrosion. Models in the 70 series utilize a 1/2"-diameter stainless steel bar, while the 79 series uses a 3/4" stainless steel bar. The bar is always provided in US32D. The spring, washer and nut are provided in a clear zinc finish.

GJ70-79 Catalogue

Door Pull 11

This door pull has 8" center to center screw spacing. The base is 3/4" diameter, the overall lenght is 9-1/4". The projection is 2-1/8" and the clearance is 1-1/2". Also known as a 8" Center Door Grip or Door Handle. This handle is shipped with thru bolts and finish washers.

Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.

Finishes

LCN SEM7850 Magnetic Door Holder

Floor Mounted Door Stop 535

Cast Brass or Bronze construction
2-1/2" diameter base x 3-1/8" high
Fasteners included

Door Holder / Stop Rubber Shoe

Replacement Rubber Shoe
5/8" insert diameter
1" base diameter
7/8" overall height

Ives Part # HRT or FSPART.1075

Non swivel chair glides for round tubing

3/4" outside diameter
9/16" and 5/8" inside diameter
1-1/16" base diameter
Nickel plated metal base

LCN SEM7820 Magnetic Door Holder

LCN SEM7840 Magnetic Door Holder

Ives Floor Mounted Door Holder FS446

Features:

• Manual type floor holder ideal for interior or exterior use.
• Cast brass or aluminum construction.
• Accommodates door undercut up to 2-1/2".
• Non-marring rubber tip.
• Unit functions as a stop but serves as a Hold-Open device when hook is manually engaged instrike. Unit requires manual disengagement to release Hold-Open.
• Packed with expansion shield and lead shield.

Overall Height 3-3/4"
Height to Stop Center Line 2-5/8"
Diameter 2-1/2"

Door Pull 24

This door handle features a 6" center to center screw spacing. It ships with thru bolts and finish washers. Also known as a Door Handle or Door Grip.

1" diameter material
6" centers
8" overall
3/4" base diameter
2" projection

Finishes

Ives Wall Mounted Door Stop WS65

• Burnished cast aluminum.
• Replaceable non-marring white rubber bumper.
• Packed with sheet metal screws.

Base Diameter: 1-5/8"
Overall Projection: 3-3/4"

Heavy Duty Non-Swivel Leveler with nylon base table glide.   Has a thread of 1/4-20, base diameter of 1 5/8" and a stem length of 1 1/2". This heavy duty glide screws into a threaded hole in the leg or table to selected height. Use with a Tnut to install on a wooden leg. 

Rubber Shoe For GJ1154M and GJL444-555 Kickdown Door Stop / Holder

Replacement rubber shoe
5/8" insert diameter
1" base diameter
8-32 threaded screw

Plunger Type Door Holder / Stop 583

Solid Cast Brass with black rubber shoe. 5-3/8 × 2-1/4" Base 1-1/4" Projection 1-1/4" Throw.

aluminum bleacher clips 3-1/2".The grooves are 3" for the outer groove and 2" apart are the inner grooves. Includes bolt and nut which are zinc cadmium plated.

Bleacher 1st row riser board holding arm assembly for wood bleachers.

The 2½" Aluminum Bleacher Clip is also known as Part #P2041U.

The 2½" Aluminum Bleacher Clips feature grooves 2-1/8" for the outer groove and 1" apart are the inner grooves. This clip replaces the 2-1/8" smaller version clip. You would use the outer and inner groove to make 1-3/4" between grooves. The 2½" Aluminum Bleacher Clip package includes a bolt and nut which are zinc cadmium plated.

Make your bleachers safe and secure with the reputable 2½" Aluminum Bleacher Clips. The durable 2½" Aluminum Bleacher Clips are designed to securely fasten bleacher seats to the supporting structure, ensuring safety and stability for spectators. Installation involves a quick setup and adjustments as needed. Each 2½" Aluminum Bleacher Clip is engineered to withstand heavy use, providing peace of mind during events. Made from high-quality aluminum, 2½" Aluminum Bleacher Clips hold up against rust and corrosion, making them ideal for both indoor and outdoor use. Whether you are managing a sports facility, school auditorium, or community center, the Aluminum Bleacher Clips 2½" are an essential component for maintaining the integrity of your bleacher system.

In addition to regular inspections, it is important to stay educated about the proper use and maintenance of the bleachers with information and/or training to help ensure that all staff understands how to operate the bleachers safely and effectively. Encourage your team to report immediately any replacements needed—whether it's loose 2½" Aluminum Bleacher Clips or damaged boards—so that repairs can be made promptly. We recommend keeping a maintenance log to track inspections and repairs for your bleachers. This can help you stay organized and ensure that nothing is overlooked. Regular maintenance not only enhances safety but also improves the overall appearance of your bleachers, making them more inviting for spectators.

For more information on specifications of the Aluminum Bleacher Clips 2½", please feel free to contact our customer service team. We can help you choose the best replacement part for your bleachers, whether it be the 2½" Aluminum Bleacher Clip or another product.

Handicap Door Pull 18

With this handle you are able to get a closed fist behind the pull, which makes it a great ADA Door Pull. Shipped with screws. Also known as a Handicap Grip, ADA Door Pull or Handle.

Finishes

Angle Base Window Handle

Cast white bronze with a brushed nickel finish

Metpar Partitions Bottom Door Insert For 7/8" Door

Chrome plated Zamac die cast construction. The door insert measures 2-5/16" wide by 1" wide by 1-3/16" high. The hex shaped hole is 5/8" and the round hole is 7/32" diameter. The material or rim is 5/16" high. Also known as a Bathroom Stall Door Insert Bottom 7/8". Manufacture part # 1530.

Ribbed Koroseal Vinyl butt-type nosing for front edge of stages, bowling lane steps, platform-like floors and bar foot rests. Grooved cutting guides provide “cut-offs” to match flooring thickness. Standard 8’ lengths; easily cut to size. Install with #400 Neoprene Contact Cement or #300 Water-based Contact Adhesive.

SPECIFICATIONS:

Furnish and install No.101 Heavy Duty Koroseal Vinyl Ribbed Butt-Type Nosing; 3-1/2” deep; 1-5/16” nose depth; square adjusta-nose. Cut nosing at proper guide to butt against 1/8” (or 3/16” or 1/4”) flooring. Select from standard colors of black or brown.

Shipping - Due to shipping restrictions, this product ships in two 48" long pieces.

4" Kickdown Door Holder / Stop FS544

This is one of our most popular Kickdown Door Holder/Stop for the past 35 years.

Features:

• Units provide an economical method to hold open doors.
• Cast of durable iron.
• Non-marring rubber shoes have corrugated bottoms to provide secure grip. Rubber shoe is securely fastened with screw. When worn, shoes are easily replaced.
• FS544 for door-to-floor clearances of 2" or less.

Flush Metal Partitions Bottom Door Insert For 7/8" Door

Chrome plated Zamac die cast construction. The door insert measures 2-5/16" wide by 1" wide by 1-3/16" high. The hex shaped hole is 5/8" and the round hole is 7/32" diameter. The material or rim is 5/16" high. Also known as a Bathroom Stall Door Insert Bottom 7/8". Manufacture part # 1530.

The Burns 618 Locking Pocket Door Latch is 2-3/4 inches tall by 2-1/2 inches deep. The mortise dimensions are 2-5/16 inches tall by 1-7/8 inch deep. Base metal is Brass or Aluminum depending on the finish.