Search results for: 'latch and key 1 cable horn 4 part'

Doromatic Complete 2090 and 1090 Active Case. Includes all of the interior hardware. Just unscrew or loosen the three set screws and remove your old case and install and tighten the three set screws. Housing measures 7-1/2" long by 1-3/16" wide.

4270902740 Left Hand Aluminum Stock
4270902742 Left Hand Dark Brown Stock
4270902743 Left Hand Black * One week lead time
4270902746 Right Hand Aluminum Stock
4270902748 Right Hand Dark Brown Stock
4270902749 Right Hand Black * One week lead time

Wayne Bleacher Spacer 5/16" x 1/2"dia.

Doromatic PS914x900-2RS Power Supply

Monarch 19-V Series Chassis Assembly Cover

This is the cover for the Monarch Falcon 19-V Rim Device. The cover measures 5-7/8" tall by 2-1/2" wide with a projection of 1-7/8".

Monarch/Falcon part # 650385
Old Part # 6134

Hussey Bleacher Wheel 5" x 1-3/16" x 3/8". Also known as 2011007. Load approx. 190 - 210 lbs.

Door Pull 15

This door handle features 7-1/2" centers on the mounting screws. With 2" diameter bases. The Grip has a 2-1/4" projection with a 1-5/8" clearance. Also known as a Door Handle or Door Grip. This handle ships with thru bolts and finish washers.

Finishes

Partition panel bracket kit for 1" thick panel, One eared bracket that is chrome plated. All bracket kits include security screws to mount the brackets. Also known as 615050. 

Standard duty brass 2-1/4" knob is pinned to swivel spindle for 1-3/4" door.
Outside spindle is 3/8" solid center and inside spindle is 9/32". Inside knob
threaded 3/8-20 with two case hardened set screws.

Von Duprin 55 Dog Screw-090053

3/8" diameter x 1/2" long
new style 14 threads per inch

Von Duprin part # 090053

1" Q-Ball Floor Protector with Felt Base

The 1" Q-Ball Floor Protector with Felt Base is for use on 1" outside diameter chair and table legs. The adaptor shown on the right fits over your existing glide, and then the Q-Ball slides over the adaptor. Constructed of Gray Plastic.

Kit includes: Adaptor for 1" Leg, and Q-Ball with Felt Base

aluminum bleacher clips 3-1/2".The grooves are 3" for the outer groove and 2" apart are the inner grooves. Includes bolt and nut which are zinc cadmium plated.

The Matte Black Hadrian Headrail is constructed of aluminum and designed to fit over the top of a 3/4" Pilaster. Comes in lengths of 60", 74" and 96" and are able to be cut down to size needed. Headrails help provide stability for partitions. Known as manufacturers part number 670060-BLK, 670074-BLK, and 670096-BLK.

Von Duprin Strike 1409

This Von Duprin Strike is used for the bottom latch of the 22, 33, 33A, 55, 88 and 99 Rim Devices.  Also known as a Blade Stop.

Trim Protector Bar

A great product for applications were your door knobs and levers are getting damaged due to hand carts and other items hitting door trim. Mount this product above or below existing items on walls and doors to protect and sheild them from damage.

Material: Brass, Bronze, Stainless Steel
Material Size: 3/8" x 1-1/2"
Base: 1-3/4" x 3-1/2"
Projection: 3-1/4"

Truth Awning Operator Guide Bar Clip

This plastic clip was used to hold the older version Guide Bar or Track. The piece measures 3/4" wide, by 5/8" high, with an 11/16" projection. The clip is made of plastic.

Part # Wi39947

This Coat Hook has a 2 inch diameter base, 1-3/4 inch projection and the hook has a diameter 1-1/4 inch. The hook is mounted with a 1/4-20 hanger bolt. Base material is brass or stainless steel depending on the finish.

The 590 is made of solid brass and ships with matching screws.  The faceplate measures 1 x 6-3/4 inches, the strike is 15/16 x 2-1/4 inches and comes standard with a 12 inch rod.  The mountng screws are 1 x 6-1/4 inches on centers.

LCN Sentronic Roller

This LCN Sentronic Roller is used on all of the LCN Track Closers, and Sentronic Closers. Nylon wheel is 1-1/16" diameter by 3/8" thick. The shaft is has a 1/2" diameter by 1-1/8" long. LCN part # 4040SE-3034.  

LCN Started using this Roller Assembly in December 2018.

WingIt Grab Bar Fastener for extra strength mounting grab bars. The wingit 251-4 is designed to work for a hole 2-1/2" and 3-1/2" or deeper hollow walls with finished wall surfaces 1/4" to 1-1/2" thick. Material used is a corrosion resistant stainless steel. One require for each flange. Fasteners will support up to 300 lbs load. Also known as 251-4.

The LCN Fusible Link melts at 165 degrees to release the hold open mechanism.   Link measures 1-3/8 long by a 1/2" wide, the center to center distance on the holes is 15/16".

LCN Part Numbers:
4010-28
4110-30
4020-31

Door Pull 30

10" centers
11" overall
2-7/8" projection
1-3/4" offset

Finishes

Indoor Flag Stand - 1". These cast stands are designed to compliment any flag set. Easily movable, these are the most practical stands for general use. This flag base weighs 15 pounds. The flag stand is 12" diameter and 6" high. 

LCN Arm Screw

This screw goes by the number 4040-159, 4110-159, 4020-159, 1260-159, 1260-159, 4040-159 and 4040SE-159.   The screw has a 3/4" diameter head, 1/2" high with a 1/4" diameter shaft with 20 threads per inch (1/4-20 screw).

Republic Steel 60" st Lock Bar -47-7/8" Length, Latch finger 701730 included, uses 700308-700309 handle assembly. Also known as 7134360, 75160, 2860, 70060, rs6048, lr160.

Universal Bleacher Spring 2-1/2" long.

Von Duprin 210NL Trim

5-3/8" x 4-25/32" x 3/32"
1-31-32" projection

Global Partitions Top Hinge For Flat Surface Mounting. Stainless Steel die cast construction. Used with powder coated steel and stainless steel partition doors. Pivot hinge is 2-3/16" tall by 1-1/2" wide. The hole spacing is 1-1/2" on center. The lug projects out 1-1/2" and is 1/2" thick. The bushing on the lug is 3/8" diameter. Manufacturer part # 135580, 111723. Same part for Flush Metal and General Partitions. Shipped with mounting screws. A=1-7/6". Also used with Accurate Partition doors after January 2013.

Tubing is 1″ diameter x 20 gauge with a satin finish. 42" Length will be as specified. Rod is held captive by flanges when installed properly. Rod may rotate in flanges if turned by hand. Correctly installed rod and flanges will support specified shower curtain(s) hung on hooks 1200-SHU or others. Rod will bend and pull from flanges if significant body weight is suspended.

Tubing is 1″ diameter x 20 gauge with a satin finish. 72" Length will be as specified. Rod is held captive by flanges when installed properly. Rod may rotate in flanges if turned by hand. Correctly installed rod and flanges will support specified shower curtain(s) hung on hooks 1200-SHU or others. Rod will bend and pull from flanges if significant body weight is suspended.

Pull Plate 5010

The plate is .050" wought solid aluminum, stainless steel, or brass depending on the finish. The Door Pull GHE10, handles come with thru bolts. The plate has counter sunk holes and sheet metal screws in matching finish.

Finishes

3" x 12" GPL312
3.5" x 15" GPL315
4" x 16" GPL416

projects 2", ht 1-3/4"

3/4" Center to Center Hole Spacing

Glynn-Johnson 410 Series Overhead Door Holder/Stop Concealed Mounting

The perfect combination of form and function, Glynn-Johnson 410 series holders and stops offer effective door control and a low-profile design. Each model is constructed so that the channel is encased in the door and the jamb bracket is mortised in the frame. When the door is open, the arm and jamb bracket are visible. Conversely, when the door is in the closed position, the entire holder is completely concealed.

The 410 fits in a mortised channel on top of the door, if your doors are not mortised on the top of the door, you would have to mortise them out.  Replaces the older version GJ310, GJ320 and GJ330 series.

GJ410 Catalogue

The Truth Entrygard 10584 Right Hand Bracket measures 2-3/4" x 1-3/8" x 1/2".  The mounting holes are 1-5/8" on center.

Project In Handless Window Lock 1-3/8"

Cast white bronze with a brushed nickel finish